Lincat PO425 Owner's manual

IS 395 ECN 3607 Page 1 of 9
Installation, Operating and Servicing
Instructions
Electric Pizza Ovens
PO425, PO425-2, PO430, PO430-2,
PO630, PO630-2
Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________

IS 395 ECN 3607 Page 2 of 9
CONTENTS
Important Information
2
Warnings and Precautions
3
Technical Data
3
Checklist of Enclosures
3
Installation and Commissioning
4-5
Operating Instructions
5-7
Cleaning
7
Servicing, Maintenance and Component Replacement
7
Fault Finding
8
Spare Parts List
8
Accessories
8
Service Information and Guarantee
9
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE

IS 395 ECN 3607 Page 3 of 9
WARNINGS AND PRECAUTIONS
This appliance must be installed, commissioned and serviced by a qualified person
in accordance with national and local regulations in force in the country of
installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot - avoid accidental contact.
Disconnect this appliance before servicing, maintenance or cleaning.
The thermostats within this unit contain Potassium-Sodium alloy that react with
water and can cause burns. Under no circumstances should the capillary/bulb be
cut open.
TECHNICAL DATA
Model
Height (mm)
Width (mm)
Depth (mm)
Weight (kg)
PO425
375
886
902
58.0
PO425-2
675
101.0
PO430
375
966
1002
77.0
PO430-2
675
135.0
PO460
375
1286
104.0
PO460-2
675
181.0
CHECK LIST OF ENCLOSURES
Warranty card
Instructions manual
Kiln Bats –1,2 or 4 dependant on model

IS 395 ECN 3607 Page 4 of 9
INSTALLATION AND COMMISSIONING
This appliance must be earthed.
An equipotential bonding terminal is provided to allow cross bonding with other
equipment.
Install this appliance on a level surface ensuring all vents are unobstructed. Do not
site on wooden or Formica surfaces. Keep a gap of 25mm below the base and the
surface on which it is situated. See Fig 1 for minimum distances –A 100mm B
1000mm.
Fig 1

IS 395 ECN 3607 Page 5 of 9
If replacing the plug connect the terminals as follows:
Green and Yellow wire Earth E
Blue wire Neutral N
Brown wire Live L
Means of isolation with at least 3mm contact separation in all poles must be
incorporated into the fixed wiring of this appliance.
The fixed wiring insulation must be protected by insulated sleeving having a
temperature rating of 60 Deg C.
Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary
polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)
Power Ratings and wiring options
Model
kW
Supply 1N~+E 230V
50-60Hz (A)
Supply 3N~+E 400V
50-60Hz (A)
PO425
3.0
13
N/A
PO425-2
6.0
26
8.7, 8.7, 8.7
PO430
4.2
18.3
6.1, 6.1, 6.1
PO430-2
8.4
36.6
12.2, 12.2, 12.2
PO630
7.2
31.3
10.4, 10.4, 10.4
PO630-2
14.4
N/A
20.8, 20.8, 20.8
The PO425 is fitted with a 13 amp plug. All other units are fitted with a terminal
connection labelled as follows:
1 Live 1 Brown
2 Live 2 Black
3 Live 3 Grey
N Neutral Blue
N Neutral Blue (connect to the other N terminal with the supplied link)
E Earth Green/Yellow
OPERATING INSTRUCTIONS
Only qualified or trained personnel should use this appliance.
Refer to Fig 2 for control functions.

IS 395 ECN 3607 Page 6 of 9
Fig 2
Connect the appliance to the electricity supply. With all the control knobs in the ‘Off’
position, turn on at the isolator. The green neon (C) will illuminate.
Turn the top element control knob (B) to the desired setting. The amber neon (A) will
illuminate.
Turn the bottom element control knob (E) to 3 to pre-heat the appliance. The amber
neon (F) will illuminate.
The top control knob controls a thermostat, and the amber neon (A) will go off when
the oven has reached the desired temperature. The lower control knob controls an
energy regulator –the setting of 3 is a recommendation - adjust to suit individual
requirements. The lower amber neon (F) will cycle on and off as the energy regulator
controls the power to the bottom element. The energy regulator should not be left on
maximum.
The oven temperature is indicated by the dial (D). There is an audible timer (G).
To turn the appliance off, turn knob B to ‘0’ and isolated at the supply.
Safety Thermostat
All models are fitted with a safety thermostat to protect the appliance in the event of
control thermostat failure. Twin models are fitted with two safety thermostat, one per
oven.
If necessary, re-set the safety thermostat by pressing the red button (A) in Fig 3. The
re-set cannot be activated until the oven has cooled.

IS 395 ECN 3607 Page 7 of 9
Fig 3
CLEANING
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent, do not use abrasive materials.
Dry with a soft cloth.
Occasionally remove the kiln bats and sweep out any debris from the base of the
appliance.
SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT
All servicing, maintenance and component replacement on this appliance should be
carried out by one of our recommended service engineers.

IS 395 ECN 3607 Page 8 of 9
Please refer to the Service Help Desk number on the final page of this manual.
Part Number
Description
Used on
DT5
Dial thermometer
All
EL258
Element 1000W
PO425, PO425-2
EL259
Element 950W
EL260
Element 1400W
PO430, PO430-2
EL261
Element 1350W
EL262
Element 2400W
PO630, PO630-2
EL263
Element 2350W
EN10
Energy regulator
All
FE10
Foot
HA05
Door handle
KB21
Kiln bat
PO425, PO425-2
KB02
Kiln bat
PO430, PO430-2
KB03
Kiln bat
PO630, PO630-2
KN260
Control knob thermostat
All
KN261
Control knob energy regulator
KN274
Control knob timer
LA10
Lamp
NE37
Amber neon
NE38
Green neon
PL144
Mains cable
PO425
SW71
Rotary switch
All
TH101
Control thermostat
TH102
Safety thermostat
TI38
Timer
Part Number
Description
Used on
PO425/FS, PO430/FS, PO630/FS
Floor stand
PO425, PO430, PO630
PO425/SK, PO430/SK, PO630/SK
Stacking kit
PO425-2, PO430-2, PO630-2
FAULT FINDING
SPARE PARTS LIST
ACCESSORIES

IS 395 ECN 3607 Page 9 of 9
For help with the installation, maintenance and use of your Lincat equipment,
please contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out by
other persons.
To ensure your service enquiry is handled as efficiently as possible, please tell us:
Brief details of the problem
Product code
All available on serial plate
Type number
Serial number
Lincat reserve the right to carry out any work under warranty, given reasonable
access to the appliance, during normal working hours, Monday to Friday, 08:30 to
17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is
in addition to, and does not diminish your statutory or legal rights.
The guarantee does not cover:
Accidental damage, misuse or use not in accordance with the manufacturer’s
instructions
Consumable items (such as filters, glass, bulbs, slot toaster elements and door
seals.)
Damage due to incorrect installation, modification, unauthorised service work or
damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential damages.
Attendance is based on reasonable access to the appliance to allow the authorised
technician to carry out the warranty work.
Service calls to equipment under warranty will be carried out in accordance with the
conditions of sale. Unless otherwise specified, a maximum of 15 minutes of
administrative time, not spent directly carrying out servicing work, is provided for
within the warranty. Any requirement for staff attending the call to spend greater time
than 15 minutes due to administrative requirements, such as on health and safety risk
assessments, will be chargeable at the prevailing rate.
SERVICE INFORMATION