Lincat Silverlink 600 CS4 Owner's manual

IS 304 ECN 3607 Page 1 of 7
Installation, Operating and Servicing
Instructions
Silverlink 600 Electric Chip Scuttles
CS4, CS4/G, CS6
Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________

IS 304 ECN 3607 Page 2 of 7
CONTENTS
Important Information
2
Warnings and Precautions
3
Technical Data
3
Checklist of Enclosures
3
Installation and Commissioning
3-4
Operating Instructions
5
Cleaning
5
Servicing, Maintenance and Component Replacement
5
Fault Finding
5
Spare Parts List
6
Service Information and Guarantee
7
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and notices.
Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE

IS 304 ECN 3607 Page 3 of 7
WARNINGS AND PRECAUTIONS
This appliance must be installed, commissioned and serviced by a qualified person
in accordance with national and local regulations in force in the country of
installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot - avoid accidental contact.
Disconnect this appliance before servicing, maintenance or cleaning.
TECHNICAL DATA
Model
Height (mm)
Width (mm)
Depth (mm)
Weight (kg)
CS4
265
450
600
17
CS4/G
645
450
600
17
CS6
265
600
600
20
CHECK LIST OF ENCLOSURES
Warranty Card
I
Instructions Manual
Lid knob kit (CS4, CS6)
INSTALLATION AND COMMISSIONING
This appliance must be earthed.
An equipotential bonding terminal is provided to allow cross bonding with other
equipment.

IS 304 ECN 3607 Page 4 of 7
If replacing the plug connect the terminals as follows:
Green and Yellow wire Earth E
Blue wire Neutral N
Brown wire Live L
Model
Power Rating (kW)
CS4
0.5
CS4/G
1.0
CS6
0.75
This appliance is fitted with a moulded plug and lead ready to be connected to an
earthed socket.
Install this appliance on a level surface ensuring all vents are unobstructed.
Install this appliance on a level surface ensuring all vents are unobstructed. Any
partitions, walls or furniture must be of non-combustible material. Minimum
distances a 100mm B 500mm –see Fig 1.
Fig 1
Fit lid knob to lid (CS4, CS6).

IS 304 ECN 3607 Page 5 of 7
OPERATING INSTRUCTIONS
Only qualified or trained personnel should use this appliance.
Connect to the power supply and switch on –the green neon illuminates.
Select the desired setting on the control knob and allow the appliance to heat up.
The overhead gantry lamp on the CS4/G will operate in conjunction with the control
knob.
CLEANING
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent do not use abrasive
materials. Dry with a soft cloth.
SERVICING, MAINTENANCE AND
COMPONENT REPLACEMENT
Overhead lamp replacement
Turn power off and allow appliance to cool.
The bulb holders are sprung loaded - carefully push old lamp against either end
terminal until opposite end is free.
Remove lamp and reverse procedure to insert replacement. Handle the
replacement lamp by the ceramic end caps and avoid touching the glass.
Please refer to the Service Help Desk number on the final page of this manual.
FAULT FINDING