Linear DXS-32 User manual

INSTR,INSTL,DXS-32
LINEAR P/N: 216314 B
MATERIAL: 20 LB. MEAD BOND
SIZE: 8.500" X 11.000"
INK: BLACK
SCALE: 1-1
SIDE 1 OF 2
DXS-32
MINIATURE
SUPERVISED
DOOR/WINDOW
TRANSMITTER
Installation Instructions
PRODUCT DESCRIPTION
The DXS-32 is a battery powered stationary transmitter designed for use with Linear’s DXS and DX
format receivers. This transmitter can be used in a variety of wireless remote control applications.
Triggering the transmitter with its built-in magnetic switch sends a digitally coded wireless signal to
its companion receiver.
The digital DXS code format features over a million possible codes. The DXS transmitters are
precoded at the factory to unique codes, so no field coding is required. The DXS-32 can send four
different codes: alarm, restore, low battery and status.
Receivers must be programmed to the transmitter’s code before system testing and operation. Refer
to the receiver’s instructions for details on programming.
In a typical installation, the magnet is mounted on a door or window and the transmitter is mounted
on the frame. When the magnet moves more than 1/2" away from the transmitter, an alarm signal is
sent. When the magnet returns next to the unit, a restore signal is sent. The magnet is adjustable
with four height positions. A 1/4" high magnet spacer is also supplied to snap on to the base of the
magnet.
The transmitter is powered from two 3-Volt #2032 lithium batteries with an expected battery life of
up to 4 years. Every hour, the DXS-32 will send a status transmission to the receiver. The hourly
signal updates the receiver to the transmitter’s condition. By monitoring status transmissions, the
receiver can determine if a transmitter has a low battery or has been removed from the system. DXS
format receivers can monitor status signals, DX format receivers cannot.
Normally, the transmitter sends an exit/entry delay transmission code. Cutting an internal jumper
selects an instant transmission code. Cutting this jumper doesn’t change the time of the actual
transmissions, but changes the code of the signal sent so the receiver can determine the transmitter’s
function.
[phone] • FAX [phone]
USA & Canada [phone] & [phone]
Toll Free FAX [phone]
www.linearcorp.com
BY
DXS-32 FEATURES & ACCESSORIES OPENING CASE
REMOVE BATTERY PROTECTION STRIP COMPONENT LOCATIONS
MAGNET
SCREWS AND
DOUBLE STICK TAPE
ADJUSTABLE
MAGNET
SQUEEZE MAGNET TABS TO
ADJUST MAGNET HEIGHT (4 POSITIONS)
MAGNET
ADJUSTMENT
TAB (EACH SIDE)
TRANSMITTER
SCREWS AND
DOUBLE STICK TAPE
MAGNET CAN BE MOUNTED UP TO
1/2" FROM LEFT SIDE OF
TRANSMITTER
MAGNET
SIDE
MARK
TRANSMITTER
MAGNET
ALIGNMENT
MARKS
MAGNET
ALIGNMENT
MARKS
REMOVE THE CASE TOP BY TWISTING A
SMALL FLAT BLADE SCREWDRIVER IN
THE SLOT ON EITHER END OF THE TRANSMITTER
TWIST
PULL OUT & DISCARD
BATTERY PROTECTION
STRIP TO ACTIVATE
TRANSMITTER
TWO TYPE 2032
BATTERIES
ANTENNA
DELAY/INSTANT JUMPER
(CUT JUMPER FOR INSTANT)

INSTR,INSTL,DXS-32
LINEAR P/N: 216314 B
MATERIAL: 20 LB. MEAD BOND
SIZE: 8.500" X 11.000"
INK: BLACK
SCALE: 1-1
SIDE 2 OF 2
EXAMPLE INSTALLATIONS TRANSMITTER MOUNTING
ADJUSTING MAGNET HEIGHT PROGRAMMING RECEIVER
CHANGING BATTERIES LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty
Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct
from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to
consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any.
There are no obligations or liabilities on the part of Linear corporation for consequential damages arising out
of or in connection with use or performance of this product or other indirect damages with respect to loss of
property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including
implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date
as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear
Technical Services at 1-800-421-1587 for an RPA# and other important details.
FCC NOTE:
This device complies with FCC Part 15 and IC Canada Rules and Regulations. Operation is subject the following
two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless
signalling. However, there are some limitations which must be observed.
✶
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15
devices. As such, they have limited transmitter power and therefore limited range.
✶
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio
signals that occur on or near their operating frequencies, regardless of code settings.
✶
Changes or modifications to the device may void FCC compliance.
✶
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
✶
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
dealer, and these facts should be communicated to the ultimate users.
Copyright © 2000 Linear Corporation 216314 B
TRANSMITTER
MOUNTED ON
DOOR JAMB
(NOTE: SMALL END
OF TRANSMITTER UP)
(NOTE: SMALL END
OF TRANSMITTER DOWN)
MAGNET
MOUNTED
ON DOOR
MAGNET MOUNTED
ON DOOR
TRANSMITTER
MOUNTED ON
WINDOW SILL
MAGNET MOUNTED
ON WINDOW FRAME
SLIDING WINDOW
LEFT OPENING DOOR
RIGHT OPENING DOOR
TRANSMITTER
MOUNTED ON
DOOR JAMB
TRANSMITTER
MOUNTED ON
WINDOW FRAME
MAGNET
MOUNTED
ON WINDOW
SASH STILE
DOUBLE-HUNG WINDOW
ATTACH BOTTOM CASE
USING THE SCREWS OR
DOUBLE-STICK TAPE PROVIDED
NOTE: ATTACHING THE TRANSMITTER WITH DOUBLE-STICK
TAPE IS NOT ALLOWED IN UL INSTALLATIONS
ADJUST MAGNET
HEIGHT UNTIL
CASE LEVELS
ARE ABOUT EQUAL
TRANSMITTER
MAGNET
THE SNAP-ON MAGNET SPACER
CAN BE USED TO ADD 1/4" HEIGHT
TO THE MAGNET (SPACERS CAN ALSO
BE SNAPPED TOGETHER FOR MORE LIFT)
PROGRAMMING:
1. PLACE RECEIVER INTO PROGRAM
OR "LEARNING" MODE
2. ACTIVATE TRANSMITTER BY
OPENING DOOR OR WINDOW
3. VERIFY THAT THE RECEIVER
ACCEPTED THE SIGNAL
TESTING:
1. PLACE RECEIVER INTO TEST MODE
2. OPEN DOOR, VERIFY THAT THE
RECEIVER INDICATES AN OPEN DOOR
3. CLOSE DOOR, VERIFY THAT THE
RECEIVER RECOGNIZED THAT THE
DOOR IS CLOSED
OPEN
DOOR
1
SLIDE OLD BATTERIES
OUT OF BATTERY
HOLDERS
2
3 4
DISCARD OLD
BATTERIES
PROPERLY
INSERT TWO DURACELL DL2032
BATTERIES
PLUS (+) SIDE UP
INTO BATTERY HOLDERS
SEAT BATTERIES COMPLETELY
INTO HOLDERS
BE SURE BATTERIES ARE
NOT TOUCHING EACH
OTHER