Linkskey LDV-302ARC User manual

Quick Installation Guide Applicable model: LDV-302ARC 2-port DVI USB KVM w/ Audio&Mic Plus QuickSwitch Button for wired remote control
Rev. 1.0 Copyright© All rights reserved.
DVI Single Link Video up to 1920 x 1200 (digital only)
QuickSwitch button for easy switching by a mere flip!
Switching Software Client for Windows & Mac included!!
Software Hotkeys & Universal Hotkeys both available!!!
2 x USB 2.0 Hub Ports for keyboard, mouse or high-
speed USB devices!!!!
LDV-302ARC
2-port DVI USB Audio&Mic KVM
w/ Integrated Cable
Quick Installation Guide
Thank you for purchasing the LDV-302ARC DVI USB Audio &
Mic KVM Switch! With our highly reliable and quality product,
user can enjoy countless benefits from using it.
LDV-302ARC
Introduction
The LDV-302ARC is a 2-port DVI USB Audio & Mic KVM
Switch with 2 x fixed KVM cables and 1 x QuickSwitch button for
wired remote control. It also provides audio and microphone
switching function for uninterrupted multimedia experience. It
allows you to access, control, boot, and reboot multiple
multimedia computers using only one USB keyboard, mouse,
DVI monitor and a speaker set and microphone.
For computers running Windows/Mac operating systems, it also
provides an innovative and easy-to-use KVM Switcher Software
-- small Windows/Mac client application to facilitate your KVM
switching operations such as computer selection and hotkey
sequence programming, autoscanning, autoscan delay time
programming, independent/simultaneous audio & computer
Switching, etc.
The LDV-302ARC DVI USB Audio & Mic KVM Switch offers
USB 2.0 interface technology for Plug-and-Play and hot-
pluggability. In addition to connect to mouse or keyboard, those
two USB 2.0 ports can also be connected to other high-speed
USB devices. Users can enjoy maximum flexibility and
convenience with its compact and one-piece design.
Out-of-Box Installation
Take the Support CD-ROM and KVM Switch out of the box and
follow the steps below for installation….
Step 1. Insert the Support CD-ROM into your CD-ROM drive,
and the installation interface will pop up (If the Autorun
feature has not been enabled on your computer. Just
find the Autorun.exe on the CD-ROM and double-click it
to start.).
Step 2. For Windows/Mac: Just click the “Software Installation
for Windows” to start Windows switcher software
installation. To install Mac version, please copy the file
(*.pkg format) to the local hard disk and install it from
there. Follow the instructions to completion. If the
installation is complete, you will see a KVM Switcher
icon on the system tray of your desktop. Right-click to
evoke the operation menu and double-click to evoke
configuration box. For operation details of the KVM
Switcher software, please refer to the following sections.
Windows Mac OS
No live connection detected
Current active computer channel is on port 1
Current active computer channel is on port 2
The Mac version of the KVM Switcher software supports only Mac
OS 10.4 (Tiger) and later. Earlier version of the Mac OS might
or might not work well with it.
The KVM Switcher Software supports both the Windows and Mac OS
operating systems. For other OS platforms such as Linux , you
can still use the universal keyboard hotkey - ScrLk + ScrLK - to
switch computer. However, this switching hotkey is not
available on non-computer platform such as Mac OS.
Step 3. Connect a set of the fixed KVM/Audio&Mic cables to a
computer’s connectors. Connect another set of cables
to another computer. Now you can operate the KVM
Switch immediately.
Some older computers with USB interface might need to manually
enable the USB option in the system BIOS settings before you can
use any USB devices. If your USB interface does not work, please
check the USB option status in the system BIOS.
If you has not yet installed a USB mouse on your computer, there
might be an error message telling you that mouse is not detected and
prompting you to decide whether to ignore the same message in the
future, and yet you found there is no mouse movement to disable
this message….So it is suggested that you should installed your USB
mouse on your computer first, before connecting it to this KVM
Switch.
Ways for KVM Switch Operation
There are three methods to control your KVM Switch for
computer and audio/mic channel selection: using (1) the

Quick Installation Guide Applicable model: LDV-302ARC 2-port DVI USB KVM w/ Audio&Mic Plus QuickSwitch Button for wired remote control
Rev. 1.0 Copyright© All rights reserved.
QuickSwitch Button (a wired remote control), (2) a hotkey
sequence or (3) the KVM Switcher Software.
QuickSwitch button (a wired remote control)
The QuickSwitch button is a wired remote control that allows
you a direct switching control. Simply press the button to
toggle between the two computers.
You can use the QuickSwitch button to switch to an empty port that
is not connected with any computer. Normally, if you use keyboard
hotkey or the KVM Switcher software, you will not be able to switch to an
empty port (and audio/mic channel, if binding is enabled). By default, PC
port switching and audio/mic port switching are bound together, unless
you specify the audio to be fixed a specific port.
Keyboard hotkeys
User-definable hotkeys for computer selection:
Hotkey sequence = Ctrl + Alt + [command key]*
* Please refer to next section for keys that are qualified to
be used as a command key
Universal hotkey for computer toggle-switching:
Both the universal hotkey, ScrLk + ScrLk and the user-definable
hotkey, Ctrl + Alt + [command key] WILL NOT allow you to switch to an
empty port that is not connected with any computer. To force your KVM
to switch to an empty port, just press the QuickSwitch button to switch.
Universal Hotkey sequence = ScrLk + ScrLk
* For other operating systems on computer such as Linux, you
can still use this special hotkey to facilitate computer
switching. This special hotkey is not available for Mac.
HOWEVER, you can press QuickSwitch button to switch in any
case.
Each keystroke within a hotkey sequence should be pressed within 2
seconds. Otherwise, the hotkey sequence will not be validated.
After port switching, you have to wait till the KVM Switch icon
shows forth the target port before you can perform next switching again.
The KVM Switcher icon could be found on the system tray/task bar of
your Windows/ Mac OS desktop after its installation.
All the hotkeys are only functional after your computers are booting
into the OS. If you want to switch computer in the BIOS/preboot stage,
press the QuickSwitch button to switch.
KVM Switcher Software (Windows & Mac platform)
In addition to computer switching, the KVM Switcher
Software also allows you more advanced functions such as
described in the next section….
KVM Switcher Operation Reference
Switch to Computer x by Operation Menu
Right-click the KVM Switcher icon to evoke the operation
menu, then select whichever computer that is available for
switching. Once you select a computer channel, it will
immediately switch to that computer. Note that the
unconnected port(s) or the active port will be grayed-out and
non-selectable.
Windows : Operation Menu Configuration Dialog Box
Mac OS: Operation Menu Configuration Dialog Box
The Mac version of KVM switcher user: if you want the KVM
switcher open at login or kept in Doc, just select the option in the
Operation Menu accordingly.
Switch to computer x by Keyboard Hotkeys
Hit the hotkey according to your current hotkey definition:
Hotkey sequence = Ctrl + Alt + [command key]*
* The factory default hotkey setting is Ctrl + Alt + 1/2/3/4
for computer 1/2/3/4. You can also use ScrLk + ScrLk to switch
COMPUTER.
Start Auto-scan
Right-click the KVM Switcher icon to evoke the operation
menu, then select Start Auto-Scan to activate autoscanning.
Stop Auto-scan
(While autoscanning) right-click the KVM Switcher icon to
evoke the operation menu, then select Stop Auto-Scan to de-
activate autoscanning.
KVM Switcher configuration
Right-click the KVM Switcher icon and select Settings or
double-click the icon to bring up the configuration dialog box.
Define Hotkey commands
You can specify the command key as you like by typing it in.
For example, you can specify the hotkey for switching to
COMPUTER 1 as CTRL + ALT + A by typing an A (not case-
sensitive) in the editable field.
Hotkey = Ctrl+ Alt + [Command key]*
* The command key is user-definable via the configuration
dialog box
Except those control keys such as Alt, Ctrl, Shift, CAPS, Tab, Esc and
those functions keys and edit keys, all other keys on the keyboard,
including those number keys on the number pad are all qualified to be
used a hotkey command key. In addition to the software KVM Switching
by the operation menu and the user-defined hotkeys, you can always use
the universal hotkey for COMPUTER switching – ScrLk + ScrLk
Fix Audio Port at Computer x
Check this option and then select the computer to fix the
audio/mic channel to the selected computer. Once this option
is checked, the audio/mic channel will be fixed and become
non-switchable.
Auto Scan Period
Select the Autoscan period from 10 ~ 60 seconds with an
increment of 5 seconds. The Autoscan period is the time your
KVM Switch will wait to switch to next computer.
RoHS C
o
m
p
l
Technical Support
E-mail: [email protected]
Website: www.linkskey.com