Livall BH6X Series User manual

www.livall.com
Quick Start Guide

1
I.Introduction
Welcome to the User Guide for LIVALL smart cycling helmets. This Guide will help you better use this product. With
continuous improvements of our products, this Guide will be updated from time to time. You can access the latest
versionand learn more about the helmet on www.livall.com.
same function.
" > "Button " > "Button
Microphone
Indicator Light
""Button
" <"Button " < "Button
Charging port
Speaker
Speaker
Tail light
Front
Main control
Front chinstrap Rear chinstrap
Adjustment knob
Buckle
Back
II. Packing List
Helmet x1 Quick Start Guide x 1 Bling remote controller x 1
MagnetUSB charging cable x 1 Important Information and Warranty Card x 1

2
III. Wearing Instructions
IncorrectIncorrect Correct
Adjust the length of
the chinstrap Leave a gap asthick Correctly position the helmetCheck whether the buckle is properly
fastened

3
IV. Operating Instructions(Please charge the battery before use.Some models of helmets are not equipped with
Bluetooth speakers. The helmets without Bluetooth speakers could not take &make calls, listen to music and hear voice prompts.)
Start-Up
POWER ON" " function button
Press the " " button for
3-to-5 seconds
You will hear a voice saying
"POWER ON".
This device is successfully
powered up when the rear lights
come on.
remote controller keys.)
One helmet can be connected to up to two LIVALL-authorized devices at the same time. After the handlebar remote
control is connected, press the "left" or "right" button to control the helmet’s corresponding indicator light.

4
Two "beeps"
"" function button
Turn onthe device, which should
be within 5 meters of the helmet.
It will automatically connect the
helmet.
Place a device that is already ON
nearthe helmet's main control.
After the connection is established, it
(The helmets without Bluetooth
speakers could not hear such voice
prompts. Please check the taillight to see
if the helmet is connected successfully.)
When the warming light ashes
and the helmet speakers emit two
"beeps", it indicates that there is a
device nearby requiring connection
to the helmet.(The helmets without
Bluetooth speakers could not hear
such voice prompts.)
≤5m
2. Replacing device
Pressthe "" button on the helmet
within 10 seconds after you hear
to the device.When pressing the
arrow left or right key on the bling
jet remote, the right or left turning
signal appears.
Two "beeps"

5
Connect to the phone (Tip: Once connected, it can control the music player as well as make and receive calls. To ensure
the stability of the connection, please try to position your mobile phone in front of you.)
Helmet Headset
"Click to
connect"
"Pairing..."
"" function
button
hold the " " button until you
hear the "Pairing..." sound.
After the connection is completed, you can play music as well as make and answer calls as follows
To Play/Pause Music: Press the " " button on the helmetor the handlebar remote control to play/pause music.
Adjust Volume: When calls are made or music is played, press the "up/down" buttons on the handlebar remote
control or press the "</>" buttons on the helmet to adjust the speaker volume .
Previous Song/Next Song: Press the "up/down" buttons on the handlebar remote control or press and hold "</>" buttons on
the helmet to cycle through the music.
Answer/Reject Calls: When there's an incoming call, press the "" button to answer the call or press and hold to
hang up.
Dial Back: Two quick presses of the "" button on the handlebar remote control or helmet to redial
the last outgoing call.
Swith on the Bluetooth on your
phone and scan for the "Helmet
Phone" device.
Click to connect. The speakers
on both sides will make the
"Connected" sound when the
connection is completed.
"Connected"

6
"POWER OFF"
"" function button
Press and hold the " " function
button for 3 seconds.
You will hear "POWER OFF".(The
helmets without Bluetooth speakers
could not hear such voice prompts.)
This device is successfully
powered down when the rear
Charging
To charge
Plug the USB charging cable into the USB
port on the helmet. The tail charging
light is illuminated in red, indicating that
the helmet is being charged.
to indicate the full charge status.
Charging time
It is recommended that the power
of the charger is no less than 0.5A.
Charging time takes about 3hours.
Charging complete
When the charging indicator light
complete.
USB port
Indicator Light
Red light
0.5A3 HRS

7
Tip:
To ensure signal stability for connection, please try not to place your mobile phone right against your body.
Instructions for Bling remote controller
Photo-shooting
Direction-Left
Confirm
Intercom
Direction-up
Direction-Right
Direction-bottom
Press photo-shooting button one time to pull up camera mode on your
smartphone. You will see the camera mode pop up. Press photo-shooting
button again to snap a photo. (Make sure to be connected to LIVALL App)
Press direction-up key one time to increase volume. Hold down direction-up
key to play previous song.
Press the direction-right key to signal turn right.
Press the conÞrmation key (middle key) to play/pause music and answer/
end incoming calls. Hold down the conÞrmation key to reject incoming calls.
Double click the conÞrmation key to make a phone call from the last dialing out
number on your smartphone.
Press direction-down key one time to decrease volume. Hold down direction-
down key to play next song.
Hold down the intercom key to communicate your message with team riders.
(Make sure to be connected to LIVALL App to enter the Grouping mode)
Press the direction-left key to signal turn left.
Connect LIVALL Riding phone App
(for use the Walkie-Talkie function and take photos) For Android: Start LIVALL Riding. The App
will automatically connect to the helmet;
For IOS: Follow LIVALL Riding guide to connect
to the helmet.
Only if the helmet is successfully connected
to LIVALL App, SOS alert feature and LED light
indicators can work.

8
New Features (only available for BH60SE Neo, MT1 Neo, BH62 Neo, BH61S Neo)
1.Battery Status
the number of "V-shaped" LEDs (BH62 Neo), that are displayed when a helmet is initially turned on. Full battery is
indicated when all of the LEDs are on.
2. Brake Warning Light
trigger the brake warning lights.
After the helmetpowers on and stays stationary for a while, it will automatically begin saving power by going into
Note: If the helmet does not wake up, make sure the battery levels are adequate.
4. Anti-Loss Alarm
Prompted whena user’s helmet is connected to the LIVALL riding app and the distance betweenthe helmet and
smartphone exceeds 15m, both the helmet and smartphone will trigger an alarm to alert the user.
5. One-Click Voice Command
After both connections are successful (the remote control is connected to the smart helmet and the helmet
is connected to asmartphone via Bluetooth), click the intercom button on the remote control to activate the
smartphone’s voice assistant service.

9
V. Considerations
1. The helmet contains electronic parts inside. Please do not take a long ride in the rain although the helmet can
prevent the rainfrom splashing.
2. After the helmet gets wet in the rain, the water droplets might occur in the chimney of tail LED lights. The water
droplets will disappear when you put the helmet under the ventilation environment for 1-2 days.
Functions BH6X MT1 MTL BH6XNeo MT1 Neo
Smart Warning Lightings ●●●●●
LED Turn Signals●●●●●
Make a Call Via Bluetooth ● ● ● ●
Listen to Music Via Bluetooth ● ● ● ●
PTT Walkie-Talkie ● ● ● ●
SOS Alert ●●●●●
Battery Status ● ●
Brake warning lights ● ●
● ●
Anti-loss alarm ● ●
One-Click Voice Command● ●
Kind Reminder: Please refer to the Quick Start Guide for more details about the functions.

10
Charging port : Magnet USB Charging cable Electricity parameter : DC 5V/0.5A
Charging time : 3-4 hours Waterproof class: IPX4
Battery life : The max. battery life of the light is 10 hours. Listening time for music is 3-to-6 hours.
Temperature: Storage Temperature: -20°C ~45°C. Temperature for use: 0°C~40°C. Temperature while charging: 0°C~40°C.
Notes: The above data is measured by LIVALL in a controlled environment, with room temperature at 25°C,
1. Problems such as network anomalies, may result in the failure to successfullysendor receive SOS messages.
storage (six months to one year).
3. The helmet contains the battery. The battery capacity varies with temperature change. The battery life can decay
when the helmet is used at low temperatures orbelow Zero degrees Celsius.
4. Trying to clean the golden colour contacts of the charging plug sheet with metal or hard tools such as bladesor
tweezers is strictly forbidden. Please use cotton swabs with clean water or alcohol in case of cleaning. Please make sure
the charging plug is clean and try while charging the helmet.
5. If the electronic functions do not work, please charge the helmet for 3 hours and then check if it works normally.
6. The helmet contains impact detection devices. Only if you connect your helmet with LIVALL App, start ride mode
contacts set on LIVALL App can accordingly receive your SOS messages.
Note:
Performance standards:
• USA: 16 CFR 1203
• Europe: EN 1078:2012+A1:2012
• Australia: AS/NZS 2063:2008

11
LIVALL Riding App
LIVALL ON FACEBOOK
LIVALL's website : www.livall.com
• which feels secure and comfortable on the head.
• the buckle positioned away from the jawbone and the straps and buckle adjusted to be both comfortable
• How the helmet should be position on the head to ensure the intended protection isprovided (e.g. that it
should be placed so as to protect the forehead and not be pushed too far over the back of the head.
• That a helmet cannot always protect against injury.
• That a helmet subjected to a severe impact should be discarded and destroyed.
• A statement of the dangerof modifying or removing any of the original component parts of the helmet other
than as recommended by the manufacturer, and that helmets should not be adapted for the purpose of
During the usage, if the following troubles occur, please charge the product according to
quick guide of the model(the helmet can be reset during the charging). If the problems still
can not be solved, please contact the after-sales service center. (After-sales email: riding@
livall.com)
Faults:
2. The helmet is turn on, but the lights, micphone, speakers etc can not work normally;
VII. Electronic functions troubleshooting

Designed and Manufactured in Shenzhen, China
BH6X&MT Neo-QO-V1.2
LIVALL HELP CENTER