Logitech Zone Vibe 125 User manual

ZONE VIBE 125
Setup Guide

CONTENTS
English
3
Česká verze
138
Deutsch
12
Slovenčina
147
Français
21
Українська
156
Italiano
30
Eesti
165
Español
39
Latviski
174
Português
48
Lietuvių
183
Nederlands
57
Български
192
Svenska
66
Hrvatski
201
Dansk
75
Srpski
210
Norsk
84
Slovenščina
219
Suomi
93
Română
228
Ελληνικά
102
Trkçe
237
По- русски
111
246
 
Po polsku
120
255

Magyar
129

KNOW YOUR PRODUCT
Front view:
Microphone boom
USB-A receiver
Back view:
Callbutton
(answer/end/reject calls)
Music control button
(play/pause/
next track)
Volume up/down
3
English

Bottom view:
3-positionswitch
(power/ Bluetooth
®
pairing)
USB-C port
LED light
Mute button
4
English

BOX CONTENT
1
2
3
Zone Vibe 125 wireless headphones
Charging cable
USB-A receiver
USB- A
USB- C
USB- A
USB- C
4 USB-Cadapter
5 Travel bag
6 User documentation
POWER ON/OFF
1Slide the switch in the arrow’s direction
to the middle to power on the headphones
1
2
2 Once powered on,the LED light will slightly
turn white
3 There will be a voice promptthat tells you
the battery status
5
English

CONNECT YOUR HEADPHONES
a. Connect via USB-A receiver
1
Insert the receiver into the computer USB-Aport
Or insert the USB-A receiver with the USB-C
adapter to the USB-C port
Zone Vibe125is alreadypaired to thereceiver
it ships with
Once successfully paired, the LED light on
the receiver will turn solid white
2
USB- A
3
USB- C
b. Connect via BLUETOOTH®
1 Slide the switch tothe bottom in the arrow’s
direction for 2 seconds to initiate pairing
2 The LED light will flash white rapidly
3 Open Bluetooth® settings onyour device
4 SelectLogi ZoneVibe125in discoverabledevices
5 Once successfully paired, the LED light will turn
solid white
LOGI Zone
Vibe125
2 sec.
ADJUSTING HEADPHONES
1 Adjust the headphones by sliding earcups up
and down the extended part of the headband
2 It may be easier to adjust the headphones on
your head Slide the earcups up and down the
headband until they sit comfortablyon your ears
6
English

HEADPHONES CONTROLS
Note:
- Media control functionality depends on the type of application
- Call activities are always the first priority When two devices are connected, the Bluetooth®
connection will be prioritized over the receiver
Tip: Music EQ controls available on Logi Tune
MUTE
There are2 ways to muteyour microphone
L
L
L
"Muteon"
"Mute off"
Mute
Press the button to mute
Flip up or down the mic
boom to mute or unmute
Voice notifications indicate
when the microphone is on/
off mute
7
English
UC version:
Usage
Button
Action
Call controls
Answer / End call
Call
button
Short press
Reject call
2sec press
Music controls
Play / Pause
Music control button
Short press
Track forward
Double press
Volume
Volume up
"+"
Short press
Volume down
"- "
Connectivity
Bluetooth® pairing
Power button
2sec press

HEADPHONES LIGHT INDICATOR
Note:
- User-triggered behaviors, such as Bluetooth® pairing or link lost, will be prioritized then revert back to its previous status
once the behavior is completed
RECEIVER LIGHT INDICATOR
Pairing mode
Paired
Incoming call
Mute on
8
English
Category
Status
Light
White
Connectivity
Pairing
Fast blinking
Receiver connecting
Off
Receiver connected
Solid
Receiver disconnected
Off
Calls
Active call
Solid
Incoming call
Repeat "fast blinking 3 times then
LED off"
Red
Calls
Mute
Solid
Category
Status
Light
White
Power
Power ON
Turn solid white and then dim
Battery charging
Breathing
Battery fully charged
Solid
Connectivity
Bluetooth® pairing
Fast blinking
Bluetooth® / receiver connected
Turn solid white and then dim
Link lost
Dim white
Calls
Active call
Solid
Incoming call
Slow blinking
Red
Calls
Mute
Solid
Power
Low battery (< 10%)
Slow blinking
Factory reset
Fast blink from red to white for
three times then LED turn off

CHARGING
To conserve battery life, headphones automatically
power off after 30 minutes without usage.
Sleep timer could be adjusted in Logi Tune.
The LED light on the headphones will blink slowly
in RED when the battery is low.
Charging via USB cable
1 Plug the USB-C cable end into the USB-C port on
the bottom of the earcup
2 Plug the USB-Aend into the USB-A charging port on
your computer or AC adapter
3 The LED light will start breathing white when charging
The LED light will turn solid white when fully charged
– 2 hours will fully charge the battery
– 5 minutes will give you 1 hour of playback
Battery life may vary based on user,environment,
and computing conditions
4 Theheadphones canbeused with thereceiver
and Bluetooth® paired while charging
LOGI TUNE
Logi Tune helps boost your headphones performance
with periodic software and firmware updates
It is recommended to update both your headphones
andreceiver To do so,download Logi Tune from
www logitech com/tune
9
English

ADJUSTING SIDETONE
Sidetone lets you hear your own voice during conversations
so you are aware of how loud you are talking In Logi Tune,
select the sidetone feature, and adjust the dial accordingly
– A higher number means you hear more external sound
– A lower number means you hear less external sound
AUTO SLEEP TIMER
By default, your headphones will automatically power off
when not in use for 30 minutes Adjust the sleep timer in
Logi Tune To wake up your headphones, try sliding off/on
the power switch again
RESET YOUR HEADPHONES
1 Powerthe headphoneson
2 Press and hold the call button and volume ’–’ button
for 5 seconds
3 The LED light will quickly blink from red to white
for 3 times and then turns off when your headphones
are successfully reset
4 The headphones will turn off after reset
10
English