Louvolite R1723 User manual

R1723 6 CHANNEL (18 SETTINGS)
TIMER REMOTE CONTROL
operating instructions
t: 0161 882 5050 e: [email protected] w: www.louvolite.com

1. Ensure Remote is in Manual mode,
this can be changed using .
3. Press until hour ashes.
5. Press to conrm,
display will automatically move to
Minute Time setting.
SETTING THE TIME
1st time or re-setting
2. Press and hold Limit and
until a time appears.
4. To set hour time press either Up or
Down to navigate to correct hour time.
6. To set Minute Time use either Up or
Down to navigate to the correct minute
time.

7. Press to conrm,
display will automatically move to
Day setting.
9. Press to conrm.
SETTING THE TIME
8. Use either Up or Down to
navigate to the Day of setting.
10. Press & hold until display
ashes, release . Time and Day is set.

PARING THE HANDSET AND MOTOR
1. Ensure remote is in Manual mode,
this can be changed using .
3. Press and hold the Red button
on the motor until it Jogs Twice
(up once/down once).
5. To check blind/motor press
either Up or Down to
conrm correct direction of motor.
2. Press until desired channel is selected
(1 - 6).
4. Press Conrm on the handset until the
motor jogs twice (up once/down once).
NOTE: If the blind is travelling in opposite
direction press and hold Limit and Stop
simultaneously until the motor jogs twice.

1. Ensure remote is in Manual mode,
this can be changed using .
3. Press and hold Limit until motor
jogs four times (up once/down once
/up once/down once).
5. Press Stop when the
blind is close to top limit position.
PARING THE HANDSET AND MOTOR SETTING THE BLIND LIMIT
2. Press until desired
channel is selected (1 - 6).
4. Press Up , the blind should move
upwards.
6. To position exactly press either Up
or Down until satised with top limit
position of Blind.

7. Press Conrm. The motor will
jog twice (up once/down once),
the top limit position is now set.
9. Press Stop when the blind is
close to the bottom limit position.
11. Press Conrm. The motor
will jog twice (up once/down once),
bottom limit position is now set.
8. Press Down . The blind should
move downwards.
10. To position exactly press either Up
or Down until satised with bottom limit
position of blind.
12. Both top and bottom limit positions of
the blind have been set, to operate using
the handset ensure this is in Manual mode.

1. Ensure Remote is in Manual mode,
this can be changed using .
3. Press Limit and Up simultaniously
until the motor jogs twice
(up once/down once).
5. Repeat ‘Setting the Blind Limits’ for more blinds.
SETTING THE BLINDS LIMITS
mid position setting
2. Move blind to the desired Mid-Position.
4. To operate the mid position press and
hold Stop until the blind moves.

We recommend making a note of desired programming channels, day, hour and
minute times before proceeding (see table at end of Instructions).
1. Ensure remote is in Auto mode,
this can be changed using .
3. Press and the blind
channel number on the handset.
Display will ash.
5. Press Stop to add a channel or
use either Up or Down
to navigate to required channel or
to add additional blinds channels.
PROGRAMMING A BLIND
2. Press Limit and simultaneously until
display ashes, the number 1 will appear.
4. To move between blind channel
numbers, use either Up or Down .

6. Press to conrm
movement(s).
8. Day will ash; Press either Up
or Down to select day, press
Stop to conrm selections.
10. To set hour time press either
Up or Down to navigate to
correct hour time.
PROGRAMMING A BLIND
7. Display will automatically move onto day
settings.
9. Press . Hour Time on display will
automatically ash.
11. Press Stop to conrm selection,
Minute Time will automatically ash on
display.

12. To set Minute Time, press
either Up or Down to navigate
to correct minute time then press
Stop to conrm.
PROGRAMMING A BLIND
13. To select Blind Direction select either
Up, Down or Mid Position, to navigate
press either Up or Down then Press
Stop to conrm selection.
15. Press and hold until
Time on Display ashes, next
“No (Number)” will appear.
14. If the display on the handset is no
longer ashing, everything is set.
If you have set all the blinds required then go to Step 16, to set further blinds go to
15 and then repeat from step 1.
16. Note: You can press Conrm to exit
the programming mode if the timing
data is complete.