LUCCI Air AIRFUSION CLIMATE II User manual

V3.0-EN ( 07/ 2019)
LUCCI
AIRFUSION CLIMATE II
DC CEILING FAN
INSTALLATION
OPERATION
MAINTENANCE
WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

Airfusion Climate Installation Instructions
1 | P a g e
THANK YOU FOR PURCHASING
Thank you for purchasing the latest in energy saving ceiling fans. This fan runs on DC (direct current) power which gives
it the benefit of being super energy efficient whilst still maintaining high volume air-movement and silent operation.
Energy saving - The DC motor is the latest technology in fan design. Its highly efficient motor saves up to 65% more
energy than ceiling fans with traditional AC motors.
Silent operation – This DC fan motor is programmed with a stabilised current which efficiently reduces motor noise.
Low operating temperature – The DC power is managed effectively which brings down the motor operating temperature
to less than 50℃. This results in a much cooler motor than a standard AC fan and increases the longevity of the motor.
6 speed remote control - Regular AC ceiling fans usually come with only 3 speeds, this DC fan comes complete with a
6 speed remote, which gives a greater choice of comfort levels.
SAFETY PRECAUTIONS
1. In Europe: This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning the use of the appliance in a safe way and understand the hazards
involved. Cleaning and maintenance shall not be undertaken by children without supervision.
2. In Australia: The appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a person responsible for their safety.
3. Children should be supervised to ensure that they do not play with the appliance.
4. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local wiring
rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the minimum
electrical safety of this standard.
Please note warranty will be void if installation is without a means for an
all-pole disconnection incorporated in the fixed wiring in accordance with

Airfusion Climate Installation Instructions
2 | P a g e
the wiring rules.
Example: If a fan is connected to a circuit that can be isolated via an all-
pole safety switch at the switchboard, then this is considered to be an
all-pole disconnection to the ceiling fan electrical circuit, meeting the
requirements of clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch on the active of the receiver input of remote
control must also be included in the wiring, and located the same
room as the ceiling fan.
5. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous substances can leak into the ground water
and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 30kg.
7. The fan should be mounted so that the blades are at least 2.3 m above the floor in Europe or 2.1 m above
the floor in Australia.
8. This fan is designed for indoor use only. Mounting the fan in a location where it is subject to water or
moisture is dangerous and may increase the risk of damage, injury or electrical shock and will void the
warranty.
9. Must be assembled and installed by a licensed electrician.
10. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling
fan and contact the manufacturer, its service agent or suitably qualified persons.
11. The replacement of parts of the safety suspension system device shall be performed by the manufacturer,
its service agent or suitably qualified persons.
12. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension
system shall be performed by the manufacturer, its service agent or suitably qualified persons.

Airfusion Climate Installation Instructions
3 | P a g e
PARTS LIST
•Unpack your ceiling fan carefully. Remove all parts and hardware.
•Lay out all the components on a smooth surface and make sure there are no components missing before
assembling. If parts are missing, return the complete product to the place of purchase for inspection or
replacement.
•Check whether the ceiling fan has been damaged during transport. Do not operate/install any product
which appears damaged in any way. Return the complete product to the place of purchase for inspection,
repair or replacement.
Examine all parts, you should have the following:
1 Mounting bracket x 1 7 Remote transmitter with holder x 1 set
2 Fan assembly with hanger cover, down rod,
canopy cover and canopy x 1
8 Extra motor screws x 1 (not shown)
3 Blades x 3 9 Screw for mounting bracket x 2 (not
Shown)
4 Blade gasket x 3 10 Balancing kit x 1 set (not shown)
5 Blade bracket x 3 11 Screw for remote holder x 2 (not shown)
6 Bottom cover x 1 12 12V Battery for remote x 1 (not shown)
Fig. 1

Airfusion Climate Installation Instructions
4 | P a g e
INSTALLING THE MOUNTING BRACKET
•The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the
blade to the nearest objects or walls.
•Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 30kg,
with two long screws provided. Ensure at least 30mm of the screw is threaded into the support. (Fig. 2)
NOTE: The bracket screws provided are for use with wooden structures only. For structures other
than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable for the
mounting surface and the surrounding environment.
ANGLED CEILING INSTALLATION
This fan hanging system supports a maximum 20 degree angled ceiling
installation. (Fig. 3)
HANGING THE FAN
Lift the fan assembly onto the mounting bracket. Ensure the key slot (A) of the hanger ball is positioned on
the key pin (B) of the mounting bracket (C) to prevent the fan from rotating when in operation. (Fig.4)
Fig. 3
Fig. 2
Fig. 4

Airfusion Climate Installation Instructions
5 | P a g e
INSTALLING THE FAN
BLADE INSTALLATION
•Insert the blade screws (4) through the blade bracket (3) and place on the underside of blade (2). (Fig. 5)
•Place the blade gasket (5) on the topside of the blade. (Fig. 5)
•Align the screws with the holes and secure the blade onto bottom of the fan motor (1). Ensure the screws
are tightened equally and evenly. Over tightening the screws can damage the blade (2). (Fig. 5)
•Repeat the process for the remaining blades.
•Install the bottom cover onto the motor shaft by rotating it clockwise. (Fig. 6)
LIGHT KIT (sold separately)
•NOTE: The light kit must be installed by a licensed electrician.
•The light kit is sold separately. (SKU# 210250, 210251,
210252, 210245, 210246, 210247, 210248, 210249)
•Remove the bottom cover from the motor shaft.
•Remove the heat shrink tube from the connector. (Fig. 7)
•For further instructions, please refer to the instructions
included with the light kit.
Fig. 7
Fig. 5 Fig. 6

Airfusion Climate Installation Instructions
6 | P a g e
PREPARE AND COMPLETE THE ELECTRICAL WIRING --- WIRING DIAGRAM (FIG. 8)
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED
WIRING.
NOTE: IF THERE ARE TWO OR MORE DC CEILING FANS INSTALLED IN THE ONE LOCATION, AN
ISOLATION SWITCH IS REQUIRED FOR EACH CEILING FAN. THIS IS REQUIRED WHEN
PROGRAMMING THE REMOTE AND RECEIVER TO PAIR TOGETHER.
Ensure the motor earth wire is connected to the single earthing terminal block “2” in the diagram below.
(Fig. 8)
FINISHING THE INSTALLATION
•After completing the electrical connection at the mounting bracket terminal block, connect the ceiling fan
wiring via the quick connector plug.
• Ensure the earth wiring is secure and correct, by performing an earthing continuity test from the fan’s
accessible metal body back to the earth terminal at the terminal block on the mounting bracket.
•Loosen the 2 screws at the bottom of the mouthing bracket by half a thread. (Fig. 9)
•Slide the canopy up to the mounting bracket and allign the key holes on the canopy with the screws on the
mounting bracket. Turn the canopy until it locks into place with the narrow section of the key holes and
secure it by tightening the two screws. Avoid damaging the electrical wiring prepared previously. (Fig. 9)
•Attach the canopy cover onto the canopy by pushing the lugs into the holes. (Fig. 9)
Fig. 8
Fig. 9

Airfusion Climate Installation Instructions
7 | P a g e
USING YOUR CEILING FAN
Pairing Transmitter and Receiver – when 2 or more DC ceiling fans are installed in one location
NOTE: The pairing of Transmitter and Receiver is not required if only one ceiling fan is installed.
When more than two ceiling fans are installed near each other, please refer to the instruction below.
When two or more ceiling fans are located near each other, you may desire to have the receiver/transmitter
for each fan set to a different code so that the operation of one fan does not affect the operation of the other
fans.
The DIP switches for the transmitter (remote hand piece) are located in the battery compartment of the
transmitter. Configuring the DIP switches will allow a unique transmission code assigned to each ceiling fan.
NOTE: Ensure that you have installed a single - pole disconnection switch in the fixed wiring for each fan,
when using DIP code function.
NOTE: Ensure power to the Receiver is ON prior to pairing the transmitter with the receiver.
Transmitter/Receiver pairing for ceiling fan 1:
•Turn off the mains supply to the receivers of both ceiling fans 1 and 2.
•Slide the cover of the battery compartment of the transmitter to access the DIP switches. This will be
transmitter 1.
•Change the position of the DIP switches in the remote transmitter 1, so that it will be different to transmitter
2. Fig. 10
•Install the 12V DC battery in the compartment. Please make sure the polarity of the battery is correct.
•Turn on the power to receiver 1. Keep the power OFF to receiver 2. (Each ceiling fan must have its own
isolation switch, so that only the ceiling fan that needs to be paired with the transmitter will be ON).
•Press and hold the SET button of transmitter 1 for 8-10 seconds within 60 seconds of switching the
power to the receiver of ceiling fan 1.
If the fan has light kit attached, the light will flash on and off to indicate the paring process activated.
The fan operates at highest speed in REVERSE mode automatically for approximately 2 minutes and
then operates in FORWARD mode for approximately 2 minutes. During the paring process, DO NOT
TOUCH THE REMOTE FOR 4-5 MINUTES.
•Now the transmitter should be paired with the receiver of ceiling fan 1. Turn ON/OFF or change the speed
of ceiling fan 1 by the transmitter to check the operation.

Airfusion Climate Installation Instructions
8 | P a g e
Transmitter/Receiver pairing for ceiling fan 2:
•Turn off the mains supply to the receivers of both ceiling fans 1 and 2.
•Slide the cover of the battery compartment of the transmitter to access the DIP switches. This will be
transmitter 2.
•Change the position of the DIP switches in the remote transmitter 2, so that it will be different to transmitter
1. Fig. 10
•Install the 12V DC battery in the compartment. Please make sure the polarity of the battery is correct.
•Turn on the power to receiver 2. Keep the power OFF to receiver 1. (Each ceiling fan must have its own
isolation switch, so that only the ceiling fan that needs to be paired with the transmitter will be ON).
•Press and hold the SET button of transmitter 2 for 8-10 seconds within 60 seconds of switching the
power to the receiver of ceiling fan 2.
If the fan has light kit attached, the light will flash on and off to indicate the paring process activated.
The fan operates at highest speed in REVERSE mode automatically for approximately 2 minutes and
then operates in FORWARD mode for approximately 2 minutes. During the paring process, DO NOT
TOUCH THE REMOTE FOR 4-5 MINUTES.
•Now the transmitter should be paired with the receiver of ceiling fan 2. Turn ON/OFF or change the speed
of the ceiling fan 2 by the transmitter to check operation.
Fig. 10

Airfusion Climate Installation Instructions
9 | P a g e
Remote Control Buttons
○
1 - FAN SPEED CONTROL BUTTON:
There are 6 available speeds. ○ I button is for the
lowest speed, and ○ VI button is for the highest speed.
NOTE: when you turn on the fan for the first time or
switch the main power to the controller, you need to start
the fan on high “○ VI ” speed first and then choose a lower
speed. A 5-10 seconds is required to allow the DC fan
to respond to the remote each speed or fan direction
selection, as DC fans incorporate a sensor control which
controls the power to the motor.
○
2 - FAN OFF BUTTON:
Press the button to turn the fan off.
○
3 - REVERSE FUNCTION BUTTON:
Press the button to activate the reverse running function. The fan must be operating to activate the reverse
function.
○
4 - LIGHT CONTROL BUTTON:
Press the button to turn on/off the light.
THE RECEIVER PROVIDES THE FOLLOWING LEVEL OF PROTECTION:
•Lock position: the receiver has a built in safety feature to protect against obstruction during operation.
The motor will be locked from operation and will disconnect from power after 30 seconds of interruption.
Please remove obstacles before re-starting. To reset, simply turn off the power supply to the fan motor
and re-start.
•Over 80W protection: when the receiver detects power consumption which is greater than 80W, the
receiver power will be stopped and operation will immediately discontinue. Turn the receiver power on
after 5 seconds to restart the fan.
Fig. 11