LUCCI Air AIRFUSION QUEST II User manual

V2.0 – EN - IR (08/2019)
LUCCI
AIRFUSION QUEST II
CEILING FAN
WITH IR REMOTE
•INSTALLATION
•OPERATION
•MAINTENANCE
•WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

Airfusion QUEST II Installation Instructions
2 | P a g e
THANK YOU FOR PURCHASING
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and
follow all instructions carefully before assembly, installation and use of this ceiling fan. Please keep
instructions for future reference.
SAFETY PRECAUTIONS
1. In Europe: This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning the use of the appliance in a safe way and understand the hazards
involved. Cleaning and maintenance shall not be undertaken by children without supervision.
2. In Australia: The appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a person responsible for their safety.
3. Children should be supervised to ensure that they do not play with the appliance.
4. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local wiring
rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the
minimum electrical safety of this standard.
Please note warranty will be void if installation is without a means for
an all-pole disconnection incorporated in the fixed wiring in accordance
with the wiring rules.

Airfusion QUEST II Installation Instructions
3 | P a g e
Example: If a fan is connected to a circuit that can be isolated via an
all-pole safety switch at the switchboard, then this is considered to be
an all-pole disconnection to the ceiling fan electrical circuit, meeting the
requirements of clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch on the active of the receiver input of remote
control must also be included in the wiring, and located the same
room as the ceiling fan.
5. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous substances can leak into the ground water
and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 30kg.
7. The fan should be mounted so that the blades are at least 2.3 m above the floor in Europe or 2.1 m above
the floor in Australia.
8. This fan is designed for indoor use only. Mounting the fan in a location where it is subject to water or
moisture is dangerous and will void the warranty.
9. Must be assembled and installed by a licensed electrician.
10. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling
fan and contact the manufacturer, its service agent or suitably qualified persons.
11. The replacement of parts of the safety suspension system device shall be performed by the manufacturer,
its service agent or suitably qualified persons.
12. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension
system shall be performed by the manufacturer, its service agent or suitably qualified persons.

Airfusion QUEST II Installation Instructions
4 | P a g e
PARTS LIST
•Unpack your ceiling fan carefully. Remove all parts and hardware.
•Lay out all the components on a smooth surface and make sure there are no components missing before
assembling. If parts are missing, return the complete product to the place of purchase for inspection or
replacement.
•Check whether the ceiling fan has been damaged during transport. Do not operate/install any product
which appears damaged in any way. Return the complete product to the place of purchase for inspection,
repair or replacement.
•Examine all parts, you should have the following:
1. Canopy screw x 4
2. Mounting bracket x 1
3. Screw for mounting bracket x 2
4. Blade screw x 8 (and 1 spare)
5. Blade holder screw x 12
(and 1 spare)
6. Blade holder x 4
7. Blade x 4
8. Blade holder nut x 12 (and 1 spare)
9. Fan assembly with motor,
down rod and canopy x 1
10. Decorative cover x 1
11. Light connector x 1 (for models with light kit only)
12. Light base x 1 (for models with light kit only)
13. Screw nut x 1 (for models with light kit only)
14. Glass shade x 1 (for models with light kit only)
15. Receiver x 1
16. Remote x 1 set
Fig. 1

Airfusion QUEST II Installation Instructions
5 | P a g e
INSTALLING THE MOUNTING BRACKET
•The ceiling fan must be installed in a location so that the blades are a minimum 300mm spacing from the
tip of the blade to the nearest objects or walls.
•Install the mounting bracket to the ceiling joist or structure that is capable of carrying a load of at least 30kg,
with the two long screws provided. Ensure at least 30mm of the screw is threaded into the support. (Fig. 2)
NOTE: The bracket screws provided are for use with wooden structures only. For structures other
than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable for the
mounting surface and the surrounding environment.
ANGLED CEILING INSTALLATION
This fan hanging system supports a maximum 18 degree
angled ceiling installation. (Fig. 3)
Fig. 3
Fig. 2

Airfusion QUEST II Installation Instructions
6 | P a g e
BLADE INSTALLATION
BLADE ATTACHMENT (Fig. 4)
1. Before installing the blades, remove the blade screws that pre-installed on the fan motor assembly.
2. Install the blade to the blade holder by tightening the blade holder screw and nut set using the included
allen key.
3. Insert the hook of the blade holder into the square hole of motor.
4. Align the 2 mounting holes on the blade holder to the 2 mounting holes on the fan motor assembly and
using the 2 blade screws (removed in step 1) to secure the blade to the fan motor assembly.
5. Ensure the screws are tightened equally and evenly to reduce the chance of warping or unbalancing.
Take care not to over tighten the screws as this can damage the blades.
6. Once completed, repeat the process on the remaining blades
Fig. 4

Airfusion QUEST II Installation Instructions
7 | P a g e
HANGING THE FAN
Lift the fan assembly onto the mounting bracket. Ensure the key slot (A) of the hanger ball is positioned on
the key pin (B) of the mounting bracket (C) to prevent the fan from rotating when in operation. (Fig.5)
LIGHT KIT INSTALLATION (For models with fan light kit only)
1. Remove the decorative cover from the shaft at the base of the fan.
2. Pull the L and N wire out from the shaft.
3. Insert the L and N wires through the light connector (1).
4. Install the light connector onto the shaft and secure firmly with a spanner.
5. Install the light base (2) onto the copper connector (1) and secure by tightening the nut (3).
6. Connect the L and N wire from the fan to the terminal block (4).
7. Remove the nut (6) from the terminal block (4).
8. Install the wire protective cover (5) onto the terminal block (4) and secure with the nut (6). The wire
protective cover(5) must cover the L and N wires from the motor shaft to the light kits terminal block (4).
9. Install a globe (not included) into the lamp holder. Do not exceed the maximurm wattage rating.
10. Install the glass shade (7) onto the lamp base (2). Ensure it is secure using three spring clips (8).
Fig. 6
Fig. 7
Fig. 5

Airfusion QUEST II Installation Instructions
8 | P a g e
ELECTRICAL WIRING DIAGRAM
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED
WIRING.
Ensure the motor earth wire is connected to the single earthing terminal block “2” in Fig. 8
Refer to Fig. 8 and following the wiring instruction below:
•Connect “LIVE” supply wire to the “L” of terminal block (1) on the mounting bracket. (Fig. 8)
•Connect “NEUTRAL” supply wire to the “N” of terminal block (1) on the mounting bracket. (Fig.8)
•Connect ground “EARTH” wire to the “ ” of terminal block (1) on the mounting bracket. (Fig. 8)
•Connect motor “EARTH” wire from motor to the “ ” of Earth terminal block (2) of the mounting bracket.
(Fig. 8)
•Connect the output quick connector (4) from the receiver to the quick connector (4) from the fan body.
(Fig. 8)
•Connect the quick connector (3) from the fan mounting bracket to the input quick connector (3) from the
receiver.
•Connect the connector (5) from the infrared detector to the input connector (5) from Remote receiver.
Fig. 8

Airfusion QUEST II Installation Instructions
9 | P a g e
FINISHING THE INSTALLATION
•After completing the electrical connection at the mounting bracket terminal block, connect the ceiling fan
wiring via the quick connector plug.
•Ensure the earth wiring is secure and correct, by performing an earthing continuity test from the fan’s
accessible metal body back to the earth terminal at the terminal block on the mounting bracket.
•Cover the mounting bracket with the canopy. Ensure all electrical wiring is tucked inside the canopy and
that the wires are not damaged during this step. Secure the canopy to the hanger bracket using the screws
provided. (Fig. 9)
•Switch ON mains power supply to the fan. Test the fan operations or enjoy using the fan following
instructions the under “USING YOUR CEILING FAN” section of this instruction manual.
USING YOUR CEILING FAN
BATTERY INSTALLATION
1. 1x CR2025 3V battery is required to operate the remote
control.
2. Loosen the screw (6) and pull out the battery tray (2) by
pressing the clip (1) and pulling out the battery tray together.
3. Place the battery (3) on the tray and insert the tray back into
the remote hand set (4).
4. Ensure the polarity is correct as shown in the battery
compartment. (5)
5. Reinstall the screw (6) to secure the battery tray (2).
Fig. 9
Fig. 10

Airfusion QUEST II Installation Instructions
10 | P a g e
OPERATING THE REMOTE:
Before you start using the remote, take the time to read through this section and get familiar with the buttons
and function of each button. (Fig.11)
1. IR TRANSMITTER
2. HI button: Press the button to set fan running at High speed.
3. MED button: Press the button to set fan running at Medium speed.
4. LOW button: Press the button to set fan running at Low speed.
5. OFF button: Press the button to turn OFF the fan.
6 / 7 / 8. 1Hr / 3 Hr / 6Hr fan timer button: Press the button to activate the fan timer function, the fan will turn
off after running 1 hour / 3 hours / 6 hours.
9. LIGHT button: Press the button to turn ON, press again to turn OFF the light.
The remote has memory function. If the fan or light is turned off by the isolating switch, it will memorise and
recover the last status when turned on next.
Effective distance/location for IR remote control (Fig. 12)
Left from center-line: Approximately 45 degrees
Right from center-line: Approximately 45 degrees
Distance from remote control to receiver: 5 meters max.
Fig. 11
Fig. 12