LUCCI Air GRENADA Series User manual

V3.0- EN– Published on 10. 2019 (Separate earth)
LUCCI
GRENADA SERIES
CEILING FAN
⚫INSTALLATION
⚫OPERATION
⚫MAINTENANCE
⚫WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

Grenada Installation Instructions
2 | P a g e
V3.0- EN– Published on
10. 2019 (Separate earth)
THANK YOU FOR PURCHASING
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and
follow all instructions carefully before assembly, installation and use of this ceiling fan. Please keep
instructions for future reference.
SAFETY PRECAUTIONS
1. In Europe: This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning the use of the appliance in a safe way and understand the hazards
involved. Cleaning and maintenance shall not be undertaken by children without supervision.
2. In Australia: The appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a person responsible for their safety.
3. Children should be supervised to ensure that they do not play with the appliance.
4. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local wiring
rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the
minimum electrical safety of this standard.
Please note warranty will be void if installation is without a means for
an all-pole disconnection incorporated in the fixed wiring in accordance
with the wiring rules.

Grenada Installation Instructions
3 | P a g e
V3.0- EN– Published on
10. 2019 (Separate earth)
Example: If a fan is connected to a circuit that can be isolated via an
all-pole safety switch at the switchboard, then this is considered to be
an all-pole disconnection to the ceiling fan electrical circuit, meeting the
requirements of clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch on the active of the receiver input of remote
control must also be included in the wiring, and located the same
room as the ceiling fan.
5. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous substances can leak into the ground water
and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 30kg.
7. The fan should be mounted so that the blades are at least 2.3m above the floor in Europe or 2.1m above
the floor in Australia.
8. This fan is suitable for indoor and alfresco areas where the fan is fully undercover with a minimum of 2
walls. This fan is not waterproof. When installed in an alfresco area, the ceiling fan must be positioned in
a location protected from water, wind, dust and salt. Exposure to these elements will void the warranty.
Mounting the fan in a situation where it is subject to water or moisture is dangerous.
9. Must be assembled and installed by a licensed electrician.
10. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling
fan and contact the manufacturer, its service agent or suitably qualified persons.
11. The replacement of parts of the safety suspension system device shall be performed by the manufacturer,
its service agent or suitably qualified persons.
12. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension
system shall be performed by the manufacturer, its service agent or suitably qualified persons.

Grenada Installation Instructions
4 | P a g e
V3.0- EN– Published on
10. 2019 (Separate earth)
BEFORE INSTALLATION
•Unpack your ceiling fan carefully. Remove all parts and hardware.
•Lay out all the components on a smooth surface and make sure there are no components missing before
assembling. If parts are missing, return the complete product to the place of purchase for inspection or
replacement.
•Check whether the ceiling fan has been damaged during transport. Do not operate/install any product
which appears damaged in any way. Return the complete product to the place of purchase for inspection,
repair or replacement.
•Examine all parts, you should have the following (Fig. 1):
1. Downrod with ball joint x 1
6. Mounting bracket screws x 2 (for wood
structure)
2. Fan motor assembly with Decorative junction
box x 1
7. Blade bracket / blade screws x 15 + (1 spare)
3. Canopy with mounting bracket x 1 set
8. Blade mounting screws x 10 + (1 spare)
4. Blade mounting bracket x 5
9. Balance kit x 1 set
5. Blades x 5
10. Wall switch x 1 set
Fig. 1

Grenada Installation Instructions
5 | P a g e
V3.0- EN– Published on
10. 2019 (Separate earth)
INSTALLING THE MOUNTING BRACKET
•The ceiling fan must be installed in a location so that the blades are a minimum 300mm spacing from the
tip of the blade to the nearest objects or walls.
•Secure the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least
30kg, with the two long screws provided. Ensure at least 30mm of the screw is threaded into the support.
NOTE: The bracket screws provided are for use with wooden structures only. For structures other
than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable for the
mounting surface and the surrounding environment.
ANGLED CEILING INSTALLATION
This fan hanging system supports a maximum 20 degree
angled ceiling installation.
Fig. 3
Fig. 2

Grenada Installation Instructions
6 | P a g e
V3.0- EN– Published on
10. 2019 (Separate earth)
ASSEMBLYING THE FAN
Install the down rod to the motor (fig. 4)
1. Loosen the hanger ball via the set screw. (see Fig.4)
2. Feed the down rod through the canopy.
3. Insert the motor wires through the down rod, and then
secure the hanger ball back to the down rod.
4. Insert the down rod to the coupling, line up the coupling
holes with the down rod holes and insert the bolt. Then
insert the pin to end of the bolt.
5. Finally secure the down rod and coupling by tightening two
set screws on the coupling.
Blade attachment (Fig. 5 & Fig. 6)
1. Assemble the blades and blade bracket together using the blade bracket / blade screws set. (Fig. 5)
2. Remove the blade mounting screws and spring washer from the motor, and remove the plastic spacer
locking the rotating part of the motor from moving during transpotation.
3. Secure the blade assembly onto the motor by tightening 2 screws with spring washers. Ensure all screws
are tightened envently to reduce the chance of warping or unbalancing. (Take care not to over tighten as
this can damage blades). Repeat the process on remaining blades. (Fig.6)
Fig. 4
Fig. 6
Fig. 5

Grenada Installation Instructions
7 | P a g e
V3.0- EN– Published on
10. 2019 (Separate earth)
Hanging the fan (Fig. 7)
Lift the fan assembly onto the mounting bracket. Ensure the key slot (A) of the hanger ball is positioned on
the key pin (B) of the mounting bracket (C) to prevent the fan from rotating when in operation. (Fig.7)
LIGHT KIT Installation (Light kit – sold separately)
NOTE: Light kit must be installed by a Licensed Electrician.
NOTE: The light kit and bulbs are NOT included with this ceiling fan and is available as optional.
1. Take off the cover from the decorative junction box by loosening the cover screws (Fig.8)
2. Push the cover cap out from cover.
3. Insert the L and N light wires (Fig. 9) through the hole of the cover. (Fig.8)
4. Tighten the fan light kit to light housing cover firmly. Secure light kit to light housing cover via a screw nut
and washer.
5. Connect the L and N light kit wires to terminal block inside decorative junction box and secure the light
kit nut (Fig. 9) to the cover (Fig.8).
6. Secure the cover (Fig.8) and the light kit (Fig.9) assembly back to decorative junction box by 3 screws.
7. Install bulb, and then turn on the power. (Refer to the Fan Light kit instructions for further details)
Fig. 7
Fig. 8
Fig. 9
Decorative
Junction Box
Cover screws
Cover
Cover Cap
Fan Light Kit
L – wire
N – wire
Light Kit nut
Bulb not
included

Grenada Installation Instructions
8 | P a g e
V3.0- EN– Published on
10. 2019 (Separate earth)
ELECTRICAL WIRING THE FAN
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED
WIRING.
NOTE: Wiring diagram includes the light kit wiring. The light wiring diagram and switch is omitted
when no light kit is used with the ceiling fan.
USE WITH WALL SWITCH WIRING DIAGRAM:
Ensure the motor earth wire is connected to the single earthing terminal block “2” in the diagram below. (Fig.
10)
Fig. 10

Grenada Installation Instructions
9 | P a g e
V3.0- EN– Published on
10. 2019 (Separate earth)
USE WITH REMOTE WIRING DIAGRAM: (REMOTE sold seperately)
Ensure the motor earth wire is connected to the single earthing terminal block “2” in the diagram (Fig. 10),
for (Fig.11 and Fig.12)
1/ Remote without quick connectors (manual wiring)
2/ Remote with quick connectors (using quick connectors)
Fig. 11
Fig. 12

Grenada Installation Instructions
10 | P a g e
V3.0- EN– Published on
10. 2019 (Separate earth)
FINISHING THE INSTALLATION
•After completing the electrical connection at the mounting bracket terminal block, connect the ceiling fan
wiring via the quick connector plug.
•Ensure the earth wiring is secure and correct, by performing an earthing continuity test from the fan’s
accessible metal body back to the earth terminal at the terminal block on the mounting bracket.
•Cover the mounting bracket with the canopy. Ensure all electrical wiring is tucked inside the canopy and
that the wires are not damaged during this step. Secure the canopy to the hanger bracket using the screws
provided. (Fig. 13)
•Switch ON mains power supply to the fan. Test the fan operations or enjoy using the fan following
instructions the under “USING YOUR CEILING FAN” section of this instruction manual.
USING YOUR CEILING FAN
FAN WALL CONTROL
Turn on the power and check the operation of the fan.
• OFF Position – Fan off
• 3rd Position –Low fan speed
• 2nd Position – Medium fan speed
• 1st Position – High fan speed
LIGHT CONTROL
• Toggle Switch – On/off
Fig. 14
Fig. 13