LuCell LU-1000 User manual

User Manual 2
Basic
Components
01
Basic
Components of
the LuCell safe
Names for each
Safe
Touch panel Start button
Safe front Body
Rack
Password change button
Battery case
High strength bolts
Alarm
Manual
Impact Alarm
9V battery Rack & hanger (4)
DC 6V Adapter Key and card pocket Fingerprint module

User Manual 3
Soft
Touch
02
1. Press the Start button at the center of touch panel in the upper part of the door
·The touch panel will be activated if you press the start button
·If you press the button twice in a row, the safe will change security mode
with the password cleared.
2. Enter the password
·The password is set to '1,2,3,4,5,6'when the safe is delivered.
·Press carefully so you do not hit an unintentionally button.
·If the password is continuously entered incorrectly ve times, the alarm will
sound for three minutes. Donot removethe battery while the alarm sounds.
wait for three minutes and then use the safe after the alarm has stopped.
3. Check 'OPEN' on theouch panel and listen to the sound.
4. Grasp the upper part of the door and open it.
·Do not use excessive force to open thedoor.
·Take care that your hand does notget jammed in the door when opening
the safe
How to open the safe
1. The door locks automatically when it is closed.
·Becareful that your hand does not get jammed in the door when closing the safe
·Close the safe completely after checking out to prevent something from getting
caught in the door.
·Keep small electronic devices,such as digital cameras, laptops, watches
(including mechanical models) stored away from the door to prevent damage
from exposure to electromagnetic elds.
How to lock the safe
Press START button Enter your password 'OPEN' displayOpen the safe

User Manual 4
Battery
03
·Durability of battery depends on the number of using, including how often the
safe is used.Change thebatteries on the assumption that it will last three to
ve months on average.
·Immediately change the tbattery in case ofabattery alarm message and
warning sound, which mean that the battery voltage is approaching the
minimum level for proper function.
·Also immediately change the battery in case of any of the following
phenomena
1) The touch panel malfunctions.
2) The LED cannotlight on.
3) The message 'GOOD' shows when thebattery is not changed.
4) The LED turns o while using the touch panel.
1. Take hold ofthe part marked 'BATTERY' on the right side of the touch panel.
2. Push and release your ngers and thebattery tray will come out.
3. Pull out the battery tray completely, remove the old battery, and replace
the new battery inthe tray, making sure to align thepolarity properly.
4. Push and release your ngers to close it.
When change
batteries
How to change
batteries
Find the part marked
'BATTERY' on the
panel, Fold and release
your ngers
Change batteries Push the battery tray

User Manual 5
1. Enter the current password and open the safe.
· You can change the password only with the door open
2. Press the Red Password change button 1 time.
·When the LCD display shows '1 USEr' and 'COdE'messages on the screen,
enter your current password.
·When the safe is delivered, thepasswrod is set to 1, 2, 3, 4,5, 6.
·If the password is correct, you will see -PASS- onthe screen
3. Enter your new code when the LCD display shows '1-COdE', and
press START button.
·The touch panel will shut o unless you press the button within four seconds
of entering a new password.
4. Enter your new password once again when the LCD display shows ' 2-COdE'
and press START button.
·If you see 'FInISH' on the LCD new password has been successfully
Password
04
Change password
Password button has been
side of door
Enter your current password
Enter your new password
once again
Press the red password
change button 1time
Password change success
Password change
complete
1 USEr message
Enter yournew password

User Manual 6
1. Open safe door and nd the alarm inside the door.
2. Push the button onthe top of the alarm to turn on the power.
3. Normal alarm setting is complete if the red power light on the LED ashes on
and o with the button to turn on.
4. The impactalarm will be activated 15 secondsafter thedoor is closed after
setting the alarm, and the safe will be protected.
(To shut o the alert sound, push the power button to turn o)
1. The alarm battery needs to be changed if the impact alarm alert sound
and the red signal have become weak, which means the battery is exhausted.
2. If you grasp the impact alarmhandle and push both ends simultaneously
you can easily attach and detach the alarm.
3. Open the cover on the back and changethe battery on the correct positive
and negative sides.
1. The impactalarm alert sound is 120 dB, and long time exposure to it may
cause damage to the hearingorgans. Thus, any use of thealarm outside
of the safe is absolutely prohibited.
2. The sudden onset ofthe aleart sound may startle pregnant women, elderly
persons, or those who are sensitive to sharp noises.
3. Instructchildren not to dismantle or ddle with the alarm.
Small impact
Alarm
05
How to activate the
alarm
How to change the
alarm battery
Notes on use
Alarm position Alarm Back cover ON/OFF button

User Manual 7
1. Press the START button at the center of touch panel in theupper part
of the door.
2. Fingerprint recognition sensor will blink.
3. When the light blinks, move your nger to the ngerprint sensor.
·The LCD displaywill show 'Err-04' mesaage if your ngerprint incorrectly
touches the sensor.
4. Check 'OPEN' message on the touch panel and listen for the sound.
5. Grasp the upper part of the door and open it
·Place your ngerprint in the middle of the sensor and closely press your
ngerprint down.
·Some ngerprints might notbe recognizable in case of their impression
is not clear.
·The lock can store maximum 10 ngerprints.
All ngerprints stored will be deleted if you choose to delete a ngerprint.
Fingerprint lock
06
How to use a
ngerprint lock
Note on use
Press the START
button
Sensoris activated Place your nger on the
ngerprint sensor
Open thedoor

User Manual 8
Note : The lock memory can save up to 10 ngerprints, and the LCD display
will show 'FULL' when the number of ngerprints excesses.
1. Enter the current password and open the safe.
·You can register the ngerprint only with the door open.
2. Before continuing, nd the red password change button inside the safe
on the left side.
·See page 2 for a diagram showing the location ofthe passwrod
change button
3. Press and hold the red password change button for 5 seconds.
·When the LCD display show '1 FIngEr' and 'COdE' messages on the screen,
enter your current password.
(If the password is correct, you will see '-PASS-' on the screen.
4. Place your ngerprint to the ngerprint sensor when the LCD display
show '1tOUCH'.
·When the display show 'OFF', take o your nger from the sensor.
·Place your ngerprint in the middle ofthe sensor and closely
press your ngerprint down.
5. When the LCD display shows '2tOUCH', place your ngerprint once
again to the sensor.
6. The ngerprint has been entered successfully if you see 'REC 01'
on the LCD display.
·The number after the 'REC' indicates how many ngerprints
stored in the memory.
How to register a
ngerprint

User Manual 9
Note : All ngerprints stored will be deleted if you choose to delete a ngerprint
1. Enter the current password and open the safe.
·You can delete the ngerprint only with the door open.
2. Before continuing, nd the red password change button inside the safe
on the left side.
·See page 2 for a diagram showing the location ofthe password change
button.
3. Press and hold the red password change button for 5 seconds.
·When the LCD display shows 'FIngEr' and 'COdE' messages on the screen,
enter your current password.
If the password is correct, you will see '-PASS-'on the screen.
4. Press the red password changebutton immediately.
5. The ngerprints have been removed successfully if the LCD display
shows 'ErASE'.
How to delete a
ngerprint
Password change button
location
Press button for
5 seconds
Press button 1time
Display 'FIngEr' and
'COdE'
Notice of deletionEnter your current
password and display
'-PASS-'

User Manual 10
AC TO DC Adapter
07
·Lucell supports hybrid power that can run on eitherbattery or adapter.
·Internal lighting can be used when the adapter is in use for power supply.
·Adapter must beDC6V 1A typewith sickle-shaped('ㄱ') connector.
·Connector is size A6 (outside dia. 5.5mm x inside dia. 2.1mm)
·Center of connector has (+) polarity, and external side has (-) polarity.
1. Check adapter jackon the lower right side ofa safe's door.
·You can feel the connector with your hands.
2. Insert adapter connector in the jack.
·Please make sure the connector is fully inserted.
3. Plug in the adapter cord, and conduct a test run before use.
·When using an adapter, battery is not used for power supply, in case of
power failure, battery use is automatically re-activated.
·Adapter needs to be purchasedseparately because of varying
voltages in dierent countries.
How to use an AC,
DC adapter

User Manual 11
1. Insert the tempered glass on rack inside, tilting itso as not to touch the
door or inner leatheratte of the safe
Rack installation
08
How to install racks

Hotline: [phone]
email: [email protected]om.sg
www.lucell.sg