LuCell MC-020 User manual

USER MANUAL
MC - 020 MC - 040
• Finger or objects may get stuck when opening and closing door.
• Keep away from children.
• Do not hit edge of safe to avoid injury.
• Be careful when moving or installing safe to avoid any injury.
• Firmly fix safe to ground when installing. When moving safe,
inquire a professional if needed.
• Improper handling of safe can cause damage to floor or table.
• Avoid placing fragile objects, such as ceramic or glass, on safe.
They may fall and cause injury.
• Place safe on dry flat surface. Safe door may not close.
Safety Precautions

01 LCD Display
02 Touch Keypad
03 Touch START Button
04 Fingerprint Scanner
05 USB Type-C Port
01 Main Body
02 Tray
03 Shelf (MC-40 only)
04 “S” Memory Button
“B” (Not in use)
“W” (Not in use)
05 Door Sensor
06 LED Light
07 Battery case
08 Alarm
09 Locking Bolts
Safe Overview
Press START Press START
Enter passcode
(initial code:123456) Pull door open
Keypad Overview
OPEN

SETTING YOUR PASSCODE
Open the door
Press ‘1’,
then press
START button
Enter new passcode
(4~20 digit), Then
press START button
“AgAin”,
then ‘_____”
will be displayed.
Enter new passcode
again, then press
START button.
“USEr_1”
will be displayed.
New passcode was set.
Press ‘2’,
then press
START button
Press “S” button
on the backside of the door
“CodE” will be displayed.
And then ‘USEr_’ will be displayed.
User 1
User 2
Enter new passcode
(4~20 digit), Then
press START button
“AgAin”,
then ‘_____”
will be displayed.
Enter new passcode
again, then press
START button.
“USEr_2”
will be displayed.
New passcode was set.
Open
the door
“CodE”
will be displayed
Press “S”
button on the
backside of the door
Enter new passcode
(4~20 digit), Then
press START button
“AgAin”,
then ‘_____”
will be displayed.
Enter new passcode
again, then press
START button.
“USEr_1”
will be displayed.
New passcode was set.
“S” button

(Press “S” button to delete
all fingerprints at once)
• screen displays “Lo_bAt”.
• safe door fails to open when “OPEn” message appears after passcode is entered.
• “good” appears on display along with “beep beep” sound after the passcode is entered.
• screen fails to turn on after you press START button.
• touch buttons are not clear enough.
• there is no reponse or malfunction.
REGISTER FINGERPRINT
REPLACING BATTERIES
DELETE FINGERPRINT
Replace batteries immediately when
• After battery replacement, confirm safe is working properly before closing door.
• Use 1.5V ALKALINE batteries (AA x 4).
• Proper insertion of batteries is confirmed once screen displays “good” message and beep is heard.
Since this is not for IOT, Emergency code will not transmit
any message to 3rd party.
If you unintentionally registered Emergency code (E-CODE),
Please make it be the same as your passcode to avoid any confusion.
Press “S” button shortly twice will lead to the E-CODE registering mode.
Open
the door
Press “S” button
on the backside
of the door
for 3 seconds
“SEt” will be
displayed
Press
“S” button
again shortly
‘FIngEr’
will be
displayed
Press ‘0’
to register
fingerprint
Scan
fingerprint
2 times
Open
the door
Press “S” button
on the backside
of the door
for 3 seconds
“SEt” will be
displayed
Press
“S” button
once
again shortly
‘FIngEr’
will be
displayed
Press ‘1’
to delete
fingerprint
Enter ID
number of
fingerprint
to delete
(Maximum 10 fingerprints
can be registered)

USB TYPE-C PORT
HOW TO USE ALARM
KEYPAD LOCK MODE
1. Use the “ON/OFF” switch on the alarm to control the Alarm.
2. Use 3 x 1.5V AAA Alkaline batteries.
In case the internal batteries have no more electricity, install 4 x AA Alkaline
batteries into the portable battery pack. Insert the USB Type-C cable
into the port to provide temporary power to open the door.
Replace internal 4 x AA batteries immediately.
USB Type-C Port
- When there is strong external impact or the safe is tilted, the alarm sounds (120dB).
- After 10 seconds from turning on the switch, Alarm is armed.
- There is light detecting sensor with the alarm. so it will be off when the door is open.
1. Activate
Press START for more the 10 seconds until “Act” appears.
“Act” message signifies activation of Keypad Lock mode.
Any input on the keypad will only display “Act”.
2. Deactivate
To deactivate KeypadLock mode, press START
for more than 3 seconds until “dEAct” appears.

SECURITY MODE
Press START button twice to hide passcode display.
[Passcode displayed] [Passcode not displayed]
[Volume displayed]
Open
the door
Press “S” button
on the backside
of the door
for 3 seconds
“SEt” will be
displayed
Press
“S” button
again twice
shortly
“VoL”
will be
displayed
Press
“0” ~ “7”
to choose
volume
Press
START

“Lo_bAt” message
appears
TROUBLE-SHOOTING
Situation Possible Cause Measures
No response when
START button pressed
Alarm continues
ringing and safe does
not work
“Err-03” message
appears
Cannot change
passcode
Forgot passcode
“Act” message
appears
• Battery discharge
• Incorrect insertion of
batteries
• Keypad Lock mode ON
• Circuit error
• Replace Alkaline batteries
• Confirm correct insertion of
batteries
• Press START for 3seconds to
deactivate Leypad Lock mode
• Contact Service Centre
• Enter correct passcode or wait
for 3 minutes until alarms stops
• Enter correct passcode
• Enter passcode within 5 seconds
• Contact Service Centre
• Contact Service Centre
• 5 times wrong
passcode input
• Incorrect passcode
• Low battery
• Keypad Lock
mode ON
• Exceed time limit
when changing passcode
• Keypad maifunction
• Button error
• Press START button for
3 seconds to deactivate
Keypad Lock mode
• Replace batteries with new
ones, preferrably Alkaline

Hotline: [phone]
email: [email protected]om.sg
www.lucell.sg