LW Scientific ZIPspin User manual

P. 770.270.1394 F. 770.270.2389 865 Marathon Parkway Lawrenceville GA 30046
See back page for model speci cations.
Instruction Manual
ZIPSpin (ZPC-06AV-0203)
Model pictured:
Ask your
authorized LWS
dealer about
additional
accessories
Upgrades:
Recommended
A Safety Switch in Lid
B Rotor (6 & 12 Tube)
C Indicator Light
D On Switch
E Variable Speed Control
F All Metal Construction
D,E
FC
B
Introduction
Performance
A
separations, as well as the centrifugation of urine specimens as outlined by C.L.I.A. Regulationss.
Maximum speed depends on the number and size of the test tubes being spun. For light loads, the
maximum speed is 7,500 rpm.
ZIPspin

P. 770.270.1394 F. 770.270.2389 865 Marathon Parkway Lawrenceville GA 3004s6
Installation & Setup
Care & Maintenance
Specications
Warranty
1
2
3
4
5
6
Remove the centrifuge from the shipping container and inspect for any possible shipping damage. If the
centrifuge appears to be damaged, please contact your distributor immediately.
Read and ll out the warranty card and return the address portion (mail or fax it to LW Scientic). The warranty
card documents your purchase. Failure to ll out and return the warranty card may void any warranty claims on
the unit.
Place the centrifuge on a sturdy, level surface. Verify that there are no loose objects or packing material in the
tube chamber.
Verify that the power switch is in the “OFF” position and plug the AC/DC adapter into an approved and properly
grounded 110V or 220V AC outlet. Do not insert specimen tubes at this time!
Turn the centrifuge on. If there is a smooth whirring sound and the unit accelerated with little or no vibration, your
ZIPSpin centrifuge is ready to operate. If there are loud or unusual sounds, or if you experience excessive
vibration, DO NOT OPERATE—Contact your dealer or LW Scientic, Inc.
Spin only balanced loads. Make sure that all tube shields are lled with equal weight tubes. Tubes of equal weight
and size should be placed opposite each other. Use sample or water to provide balance. Proper sample
balancing will improve sample separation and will extend the life of the centrifuge. Out of balance loads may
damage the centrifuge.
With proper care and maintenance, the ZIPSpin centrifuge will provide years of
service. Please follow these guidelines:
A) Never force a tube into the head. The ZIPSpin was designed for 1.5ml microtubes.
B) Clean the inside of the centrifuge. Whenever there is a test tube breakage or a
spill, it is recommended that the inside of the centrifuge be cleaned, and if possible,
disinfected (Do not immerse the electrical components in any liquid).
C) Motor and electrical maintenance: The ZIPSpin utilizes a maintenance-free brushless motor and its bearings are
permanently lubricated. It should not need servicing for the life of the centrifuge. Likewise, the electrical components
were designed for high reliability and should not need regular service. However, if repairs should be needed, please
contact LW Scientic, Inc.
Your ZIPSpin centrifuge is covered by a limited 1-year warranty
on parts and labor. If the centrifuge or any of its parts should
fail during this period, simply contact LW Scientic, Inc. for a
“Return Merchandise Authorization” for repair or replacement.
Any attempts to repair the centrifuge or replace any of its
parts without authorization from LW Scientic, Inc. may void
the warranty.
Nominal speed: 0-7,500 RPM
Maximum G-force: 2,850 g
Max. Volume: 9 ml
Max. Power: 12 volt DC
Height: 4.5 inches
Width: 6 inches
Depth: 8 inches
Weight: 3.5 lb.
Boxed dimensions: 8.5 x 10.5 x 6 in
Boxed weight: 6 lbs.
Average Speed:*
Dial Setting Range
Low 3000-4000
Half 5000-6000
Full 7000-7500
* These are average speeds, which vary slightly between units, and with load size. Please use a tachometer
for actual RPMs on your unit and for calibration purposes.