LYNXTechnik Yellobrik OTR 1440 User manual

yellobrik Quick
Reference
yellobrik ®
®
CWDM Fiber Optic /
SDI Transceiver
12G
6G/3G/1.5G
12V 0V
О
Power
WARNING
CLASS 1
Laser Product
TX
RX
IN OUT
LYNXTechnik AG
OTR 1440
12G Fiber Optic / SDI Transceiver (CWDM)
Technical Specications
SDI Video
Fiber Optic 1 x ber optic input
(Range 1260-1620nm, Sensitivity: - 14dBm to -10dBm)
1 x ber optic output
(CWDM - 18 selectable wavelengths - ITU-T G.694.2)
Optical Power: -2 to 3dBm
Duplex (Singlemode) using LC/PC Connections
SMPTE 297M - 2006
TX active LED, and RX active on side of module
Max. distance approx. 10km (6.2 miles)
Power
SDI Video
Input
SDI Video
Output
DC Power Input
LC Fiber Optic
Input / Output
We are constantly adding additional yellobrik modules.
Please visit our website for the latest product updates.
www.lynx-technik.com
LYNXTechnik AG Broadcast Television Equipment
®
WARNING
LASER RADIATION
Do not view directly with
optical instruments
CLASS 1M LASER PRODUCT
+12V DC @ 1.9W nominal - (power supply included)
(supports 7 - 24V DC input range)
Power LED on side of module
1 x SDI video input on 75 Ohm BNC connector
1 x SDI video output on 75 Ohm BNC connector
SMPTE 424M, SMPTE 292M, SMPTE 259M
Multi-standard operation from 270Mbit/s to 3Gbit/s
Return Loss: >15dB to 1.5GHz ; >10dB up to 3GHz
Automatic cable EQ (Belden 1694A cable)
250m @ 270Mbit/s, 140m @ 1.5Gbit/s, 80m @ 3Gbit/s
Power
RX Data
Present
TX Data
Active
WARNING: Module laser is active
as soon as power is connected,
regardless of LED indication

Note: OTR 1440 is identical in terms of mounting and securing
Connections
The SDI input and output is connected to the corresponding 75 Ohm
BNC connections provided (up to 12G).
The ber connection is made
with a duplex LC connector as indicated on the module. An example of
a duplex LC connector shown below.
Use the included dust plug to protect the optical connection from dust.
18 wavelengths are available to choose from when ordering the
module.
Operation
The OTR 1440 combines a CWDM ber optic transmitter and receiver
into a single package. Dierent SDI video formats and standards can be
transmitted and received up to 12G.
Data reception activity is indicated
by the RX LEDs on the side of the module.
Operation is fully automatic. The ber input video rates are
automatically detected, reclocked and provided on the BNC output
connectors. No user settings are provided for this module. The module
supports hot swapping and hot plugging of connections.
Note: If TX LED is OFF this indicates no SDI input is present, or the input signal is
not valid. I
f RX LED is OFF this indicates no signal is present, signal to weak or is a
non a valid input.
Optional Mounting Brackets
The optional RFR 1001 mounting brackets can be
used to permanently mount the modules on any
at surface or on 19‘‘ rack rails.
Power Lead Strain Relief
The modules have a small hole in the case located above the power
connection to prevent the power lead being accidentally pulled out.
Use the supplied tie-wrap and secure the lead as shown below.
The optional RFR 1000-1 rack mount can be used to permanently
mount up to 14 yellobrik modules. In addition, the RFR 1000-1 can
provide full power redundancy for all mounted yellobriks.
Note: The module is designed for use with SMF
(Singlemode) ber cable.
Power
The module requires a clean 12V DC (7-24V DC) power source. An LED is
provided to conrm power is connected. A 12V DC power supply is
included with the module. If you are applying your own power source,
please provide a clean, 7-24V DC power source. Power consumption
information can be found in the technical specications table.