M-system R3-PA4 User manual

R3-PA4
P. 1 / 3 EM-8399 Rev.2
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
the contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■ PACKAGE INCLUDES:
Pulse input module ..................................................... (1)
■ MODEL NO.
Check that model No. described on the specification label is
exactly what you ordered.
■ INSTRUCTION MANUAL
This manual describes necessary points of caution when you
use this product, including installation, connection and basic
maintenance procedures.
INSTRUCTION MANUAL
MODEL R3-PA4
HIGH SPEED PULSE INPUT MODULE
(4 points, isolated)
POINTS OF CAUTION
■ HOT INSERTION/REMOVAL OF MODULES
Removing or replacing modules does not affect other modules
on the same backplane. It is possible to replace them without
removing the power supply. However, replacing multiple
modules at once may greatly change line voltage levels. We
recommend that you replace them one by one.
■ ENVIRONMENT
• Indoor use
• When heavy dust or metal particles are present in the air,
install the unit inside proper housing with sufficient ventila-
tion.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH in
order to ensure adequate life span and operation.
■ WIRING
• Do not install cables (power supply, input and output) close
to noise sources (relay drive cable, high frequency line, etc.).
• Do not bind these cables together with those in which noises
are present. Do not install them in the same duct.
■ AND ....
• The unit is designed to function as soon as power is
supplied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data sheet.
INSTALLATION
Use the Installation Base (model: R3-BSx).

R3-PA4
P. 2 / 3 EM-8399 Rev.2
COMPONENT IDENTIFICATION
1
11
12
13
14
15
16
17
18
19
20
2
3
4
5
6
7
8
9
10
ON
8
7
6
5
4
3
2
1
SW1SW2
ON
8
7
6
5
4
3
2
1
SW3
ON
4
3
2
1
■FRONT VIEW ■SIDE VIEW
ERR LED
RUN LED
Gain Input 2 (SW1)
or
Input 4 (SW2)
Range
Input 1 (SW1)
or
Input 3 (SW2)
•Gain: SW3
■SIDE DIP SW
•Input Range: SW1, SW2 (independent range selectable)
INPUT 1 (SW1) INPUT 2 (SW1)
INPUT 3 (SW2) INPUT 4 (SW2) RANGE
12345678
OFF OFF OFF OFF OFF OFF OFF OFF
0 – 100 kHz(*)
ON OFF OFF OFF ON OFF OFF OFF 0 – 10 kHz
OFF ON OFF OFF OFF ON OFF OFF 0 – 1 kHz
ON ON OFF OFF ON ON OFF OFF 0 – 100 Hz
OFF OFF ON OFF OFF OFF ON OFF 0 – 10 Hz
ON OFF ON OFF ON OFF ON OFF 0 – 1 Hz
OFF ON ON OFF OFF ON ON OFF 0 – 0.1 Hz
SW GAIN INPUT
1 (*)2
SW3-1 OFF ON Input 1
SW3-2 OFF ON Input 2
SW3-3 OFF ON Input 3
SW3-4 OFF ON Input 4
(*) Factory setting
■ DIMENSIONS mm (inch)
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
1
11
12
13
14
15
16
17
18
19
20
2
3
4
5
6
7
8
9
10
130 (5.12)
27.5 (1.08) 109 (4.29) POSITIONING
GUIDE
TERMINAL
COVER
20–M3
SCREW
6.2
(.24)
■STATUS INDICATOR LED
RUN indicator: Bi-color (red/green) LED;
Red when the bus A operates normally;
Green when the bus B operates normally;
Amber when both buses operate normally.
ERR indicator: Bi-color (red/green) LED;
Red with the excitation abnormality;
Green in normal operating conditions.

R3-PA4
P. 3 / 3 EM-8399 Rev.2
■ CONNECTION DIAGRAM
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such
productwasoriginallypurchasedifsuchproducthasbeenusedundernormaloperatingconditionsandproperlymaintained,M-System'ssoleliability,andpurchaser'sexclusiveremedies,
under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To
submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: [phone], Fax: [phone], E-mail: [email protected]
WIRING INSTRUCTIONS
■SOLDERLESS TERMINAL mm (inch)
Refer to the drawing below for recommended ring tongue
terminal size. Spade tongue type is also applicable. Solderless
terminals with insulation sleeve do not fit. Applicable wire
size: 0.3 – 0.75 mm2
3.2 (.13) dia.
4 min.
(.16)
12 (.47) max.
6 max.
(.24)
3 (.12) max.
3
1
4
2
EXC +
INP TERM. 1
INP TERM. 2
INP TERM. 3
5
COM
INTERNAL POWER
BUS A
BUS B*
*For dual redundant communication.
BUS CONNECTOR
Input 1
8
6
9
7
EXC +
INP TERM. 1
INP TERM. 2
INP TERM. 3
10
COM
Input 2
13
11
14
12
EXC +
INP TERM. 1
INP TERM. 2
INP TERM. 3
15
COM
Input 3
18
16
19
17
EXC +
INP TERM. 1
INP TERM. 2
INP TERM. 3
20
COM
Input 4
■Input Connection Example (Input 1)
• Open Collector
1
2
3
4
5
12VDC
20kΩ
1kΩ7.5kΩ