M-system R30YV4 User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9005 Rev.2 P. 1 / 5
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
DC voltage output module..................................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside the instrument
panel of a metal enclosure.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
■GENERAL PRECAUTIONS
• Before you remove the terminal block or mount it, turn off
output signals for safety.
■HOT SWAPPABLE MODULES
• It is possible to replace a module with the power supplied
provided that the module is replaced with one with the
same model number and installed in the same base slot.
• Turn off input signals before replacing the module for
safety. Note that replacing multiple modules at once may
greatly change line voltage levels. We highly recommend
to replace them one by one.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 10 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
• Be sure to attach the terminal cover for safety.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
DC VOLTAGE OUTPUT MODULE
(4 points, isolated) MODEL R30YV4

R30YV4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9005 Rev.2 P. 2 / 5
COMPONENT IDENTIFICATION
RUN
ERR
RUN LED
Output Terminal Block
ERR LED
■FRONT VIEW
■BOTTOM VIEW
■SIDE VIEW
Lock Tab
Base Fixing Screw
Specifications
Positioning Guide
Terminal Cover
Terminal Fixing Screw
■STATUS INDICATOR LED
ID COLOR FUNCTION
RUN Green ON while network module operates normally
OFF in network module error
ERR Red OFF when internal bus operate normally
ON when internal bus error
■TERMINAL ASSIGNMENTS
11
COM1
12
COM2
13
COM3
14
COM4
15
NC
16
NC
17
NC
18
NC
19
NC
20
NC
1
V1
2
V2
3
V3
4
V4
5
NC
6
NC
7
NC
8
NC
9
NC
10
NC
NO. ID FUNCTION NO. ID FUNCTION
1 V1 Voltage Output 1 11 COM1 Common 1
2 V2 Voltage Output 2 12 COM2 Common 2
3 V3 Voltage Output 3 13 COM3 Common 3
4 V4 Voltage Output 4 14 COM4 Common 4
5 NC No connection 15 NC No connection
6 NC No connection 16 NC No connection
7 NC No connection 17 NC No connection
8 NC No connection 18 NC No connection
9 NC No connection 19 NC No connection
10 NC No connection 20 NC No connection

R30YV4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9005 Rev.2 P. 3 / 5
INSTALLATION
■INSTALLATION TO THE BASE
Use the Installation Base (model: R30BS).
The I/O slots are numbered in the ascending order starting
from the one on the immediate right side of the network
module (slot 1, slot 2...).
A code indicating the I/O slot number is assigned to each
I/O slot and I/O data is allocated in the order of this codes.
When an I/O slot is vacant, blank data is sent or received to/
from the PLC, etc.
PWR COM I/O1 I/O n
■HOW TO MOUNT THE MODULE
1) Engage the positioning guide of the module with the In-
stallation Base.
2) Pivot the module on the positioning guide and press it
down until the lock tab clicks into place.
Positioning Guide
3) Tighten the base fixing screw using a screwdriver (stem
length: 70 mm/2.76” or more) (torque 0.5 N·m).
Base Fixing Screw
■HOW TO REMOVE THE MODULE
1) Loosen the base fixing screw using a screwdriver (stem
length: 70 mm/2.76” or more).
Base Fixing Screw
2) While pressing the projection on the lock tab, push the
module upward.
3) Detach the positioning guide of the module from the In-
stallation Base.
Lock Tab

R30YV4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9005 Rev.2 P. 4 / 5
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit: mm (inch)
①
②
③
④
⑪
⑫
⑬
⑭⑤
⑥
⑦
⑧
⑨
⑩
⑮
⑯
⑰
⑱
⑲
⑳
110 (4.33)
25 (.98) 98 (3.86)
20–M3
SCREW
6
(.24)
■CONNECTION DIAGRAM
11
V1
COM1
V2
COM2
V3
COM3
V4
COM4
2
12
1
13
4
14
3
INTERNAL POWER
INTERNAL BUS
BUS CONNECTOR
OUTPUT1
OUTPUT2
OUTPUT3
OUTPUT4

R30YV4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9005 Rev.2 P. 5 / 5
WIRING INSTRUCTIONS
■TIGHTENING TORQUE
Separable screw terminal wiring screw: 0.5 N·m
Separable screw terminal fixing screw: 0.5 N·m
■SOLDERLESS TERMINAL unit: mm (inch)
Refer to the drawing below for recommended ring tongue
terminal size. Spade tongue type is also applicable. Solder-
less terminals with insulation sleeve do not fit.
Applicable wire size: 0.25 to 0.75 mm2
Recommended manufacturer: Japan Solderless Terminal
MFG. Co., Ltd., Nichifu Co., Ltd.
3.2 (.13) dia.
12 (.47) max.
6 max.
(.24)
3 (.12) max.
■HOW TO REMOVE SEPARABLE SCREW TERMINAL
The terminal block is separable in two pieces. Evenly loos-
en two screws on top and bottom of the terminal block to
separate.
FUNCTIONS
■OUTPUT AT THE LOSS OF COMMUNICATION
• Output Hold
If the network module is in error, the module holds the
signal at error and stands by until the communication re-
covers.
• Output set value
If the network module is in error, the module holds the
signal at error or power up and stands by until the com-
munication recovers. The signal at error or power up is se-
lectable with PC configurator software (Model: R30CFG).
Not depending on output at the loss of communication set-
ting, when power up the module holds the signal at error or
power up and stands by until the normal data is received.
PC CONFIGURATOR
The following parameter items can be set with using PC
Configurator Software (model: R30CFG).
Refer to the users manual for the R30CFG for detailed op-
eration of the software program.
■CHANNEL INDIVIDUAL SETTING
PARAMETER SETTING RANGE DEFAULT
SETTING
Unused setting CH enabled
CH disabled
CH enabled
Output range -10 – +10 V DC
-5 – +5 V DC
0 – 10 V DC
0 – 5 V DC
1 – 5 V DC
-10 – +10 V DC
Fine zero adjustment -320.00 – +320.00 (%) 0.00 (%)
Fine gain adjustment -3.2000 – +3.2000 1.0000
Scaled range zero -32 000 – +32 000 0
Scaled range span -32 000 – [phone]
Output range at
communication
failure or power up
-15.00 – +115.00 (%) -15.00 (%)
■CHANNEL BATCH SETTING
PARAMETER SETTING RANGE DEFAULT
SETTING
Simulate output Normal output
Simulation data
Normal output
Output at the loss
of communication
Hold the output data
User set data output
Hold the out-
put data