manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. M-system
  6. •
  7. Transmitter
  8. •
  9. M-system 10VF2 User manual

M-system 10VF2 User manual

10VF2
P. 1 / 2EM-0827
SIGNAL TRANSMITTER
(high speed response) MODEL 10VF2
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■ PACKAGE INCLUDES:
Signal conditioner......................................................... (1)
■ MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■ INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■ POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
24V DC rating: 24V ±10%, approx. 65mA
■ GENERAL PRECAUTIONS
• Before you remove the unit or mount it, turn off the power
supply and input signal for safety.
■ ENVIRONMENT
• Indoor use
• When heavy dust or metal particles are present in the air,
install the unit inside proper housing with sufficient ven-
tilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -5 to +55°C
(23 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■ WIRING
• Do not install cables (power supply, input and output)
close to noise sources (relay drive cable, high frequency
line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■ AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
COMPONENT IDENTIFICATION
INSTALLATION
Use Standard Rack (model: 10BXx).
TERMINAL CONNECTIONS
Connect the unit as in the diagram below or refer to the con-
nection diagram on the side of the unit.
CHECKING
1) Terminal wiring: Check that all cables are correctly con-
nected according to the connection diagram.
2) Power input voltage: Check voltage supplied to the rack
(model: 10BXx). For a DC power source, be sure that the
ripple level is within 10% p-p.
3) Input: Check that the input signal is within 0 – 100% of
the full-scale.
4) Output: Check that the load resistance meets the de-
scribed specifications.
Zero Adj.
Span Adj.
Specifications
Connection Diagram
(side)
Terminal Cover
Body
1
2
+
–
OUTPUT 1
7
8
CONNECTOR
OUTPUT 1
POWER
+
–
SIGNAL
SOURCE
The 10VF2, by its fast-response feature, is not designed
to eliminate noise present in the input signal.
Use a shielded twisted-pair cable for preventing noise
entering through the input wiring.
10VF2
P. 2 / 2EM-0827
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such
product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive
remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this
warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original
sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]
ADJUSTMENT PROCEDURE
This unit is calibrated at the factory to meet the ordered
specifications, therefore you usually do not need any cali-
bration.
For matching the signal to a receiving instrument or in case
of regular calibration, adjust the output as explained in the
following.
■ HOW TO CALIBRATE THE OUTPUT SIGNAL
Use a signal source and measuring instruments of sufficient
accuracy level. Turn the power supply on and warm up for
more than 10 minutes.
1) ZERO: Apply 0% input and adjust output to 0%.
2) SPAN: Apply 100% input and adjust output to 100%.
3) Check ZERO adjustment again with 0% input.
4) When ZERO value is changed, repeat the above proce-
dure 1) – 3).
MAINTENANCE
Regular calibration procedure is explained below:
■ CALIBRATION
Warm up the unit for at least 10 minutes. Apply 0%, 25%,
50%, 75% and 100% input signal. Check that the output
signal for the respective input signal remains within accu-
racy described in the data sheet. When the output is out of
tolerance, recalibrate the unit according to the “ADJUST-
MENT PROCEDURE” explained earlier.
EXTERNAL DIMENSIONS unit: mm (inch)
130 (5.12)
3 (.12)
50 (1.97)
82 (3.23)
2–4.3 (.17) dia.
MTG HOLE
TERMINAL COVER
7–M3.5 SCREW
8 (.31)
91 (3.58)
99 (3.90 )
25 (.98)
1 2
3
5 6
7 8

Other M-system Transmitter manuals

M-system M6SCTC User manual

M-system

M-system M6SCTC User manual

M-system 18KJV User manual

M-system

M-system 18KJV User manual

M-system 10SP User manual

M-system

M-system 10SP User manual

M-system F2VS User manual

M-system

M-system F2VS User manual

M-system Mini-M M2REB User manual

M-system

M-system Mini-M M2REB User manual

M-system W5MS User manual

M-system

M-system W5MS User manual

M-system MXS User manual

M-system

M-system MXS User manual

M-system M5XPA User manual

M-system

M-system M5XPA User manual

M-system M2ADS User manual

M-system

M-system M2ADS User manual

M-system Mini-M M2XUM User manual

M-system

M-system Mini-M M2XUM User manual

M-system MFS2 User manual

M-system

M-system MFS2 User manual

M-system M5VSH User manual

M-system

M-system M5VSH User manual

M-system KCNA User manual

M-system

M-system KCNA User manual

M-system 99SVA User manual

M-system

M-system 99SVA User manual

M-system M5VF2 User manual

M-system

M-system M5VF2 User manual

M-system WRS2 User manual

M-system

M-system WRS2 User manual

M-system M5PA User manual

M-system

M-system M5PA User manual

M-system M5XTR User manual

M-system

M-system M5XTR User manual

M-system 10JFT User manual

M-system

M-system 10JFT User manual

M-system 15TS User manual

M-system

M-system 15TS User manual

M-system W5-UNIT User manual

M-system

M-system W5-UNIT User manual

M-system M5CT-5AM User manual

M-system

M-system M5CT-5AM User manual

M-system M2EXV User manual

M-system

M-system M2EXV User manual

M-system M6DVF User manual

M-system

M-system M6DVF User manual

Popular Transmitter manuals by other brands

BD Sensors 17.6 Series operating manual

BD Sensors

BD Sensors 17.6 Series operating manual

RKI Instruments 65-2451RK Operator's manual

RKI Instruments

RKI Instruments 65-2451RK Operator's manual

Siemens SITRANS P500 Compact operating instructions

Siemens

Siemens SITRANS P500 Compact operating instructions

Johnson Controls H -68P3 Series installation instructions

Johnson Controls

Johnson Controls H -68P3 Series installation instructions

Hall Technologies DSCV2-70-TX-UK user manual

Hall Technologies

Hall Technologies DSCV2-70-TX-UK user manual

Ferguson REGENT i351s user manual

Ferguson

Ferguson REGENT i351s user manual

Broadcast Electronics FM-10T manual

Broadcast Electronics

Broadcast Electronics FM-10T manual

Soundcast aptX VGtx user manual

Soundcast

Soundcast aptX VGtx user manual

NIVELCO NIPRESS D 3 Series user manual

NIVELCO

NIVELCO NIPRESS D 3 Series user manual

NIVELCO EasyTREK SP-500 Series Installation and programming manual

NIVELCO

NIVELCO EasyTREK SP-500 Series Installation and programming manual

Beyerdynamic Unite TP quick start guide

Beyerdynamic

Beyerdynamic Unite TP quick start guide

Nikon WT-5 user manual

Nikon

Nikon WT-5 user manual

Linear MegaCode ACT-21 Operation instructions

Linear

Linear MegaCode ACT-21 Operation instructions

FUTABA T6EXA Quick start programming guide

FUTABA

FUTABA T6EXA Quick start programming guide

ATI Technologies D12-17 O & M Manual

ATI Technologies

ATI Technologies D12-17 O & M Manual

Emerson Rosemount 644 quick start guide

Emerson

Emerson Rosemount 644 quick start guide

INVISIBLE FENCE ICT 775 Operation and installation manual

INVISIBLE FENCE

INVISIBLE FENCE ICT 775 Operation and installation manual

Emerson Rosemount 644 Reference manual

Emerson

Emerson Rosemount 644 Reference manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.