Macnaught BOP20 BP20-PH User manual

POWER HEAD
BP20-PH
Owners Manual
PLEASE READ THIS SAFETY INFORMATION CAREFULLY BEFORE USE
Read and retain this instruction manual to assist you in the operation of your new product.
INTRODUCTION
Macnaught has designed and manufactured this pump to the highest quality standards using
premium quality materials and workmanship
• DO NOT use with Charger or Battery if equipment is worn or damaged, (remove from service)
Failure to follow all instructions listed may result in electric shock, fire, serious injury and/or
damage to the power tool The term “power tool” in all of the warnings listed refers to your battery
operated (cordless) power tool
POWER HEAD SAFETY WARNINGS
• DO NOT use product if the product is damaged or the switch does not turn the pump on.
• DO NOT store or use the power tool and battery pack in locations where the temperature may reach
or e ceed 40°C/104°F.
• Only use “ORIGINAL” Macnaught replacement parts, battery or charger
GENERAL SAFETY
• DO NOT lift the power head with locking lever. Handle power head with care. DO
NO DROP.
• Make sure the power head is securely connected/attached to the stem.
• DO NOT leave the power head sitting on top of the stem unlocked.
• Stop operating the pump if any leakings at the joints are noticed.
• DO NOT modify the pump in any way.
• DO NOT use the product in potentially e plosive atmosphere or areas.
• DO NOT e pose the product to fire and source of heat.
• Use product in well ventilated area.
• Only use genuine Macnaught battery and chargers with this product.
• Only use genuine Macnaught battery and chargers with this product.
BP20-PH-inst-issue2
1

• DO NOT ALLOW POWER TOOL TO RUN DRY
• Battery pack and power head should be protected from water.
• DO NOT e pose the power head to a nearby magnet as its performance will be
adversely affected.
• The battery operated pump should always be used in a vertical position.
• DO NOT e pose power tool to rain or wet conditions.
• Use power tool and accessories in accordance with these instructions.
• DO NOT allow power tool to operate unattended.
• DO NOT use power tool if the switch is damaged and does not turn on and off.
• Disconnect the battery from the power head before making any adjustment,
changing accessories, or storing power tool.
• DO NOT Leave the power head sitting on top of the stem unlocked.
• Keep the cordless power tool and plastic bag away from babies and children.
Power tools that are no longer
usable should not be disposed of
with household waste but in an
environmentally friendly way.
Please recycle where facilities
exist. heck with your local
council authority for recycling
advice.
ENVIRONMENTAL
GENERAL SAFETY (CONT’D)
2
DISCLAIMER
Gases, vapors, mists, and specks of dust can form e plosive atmospheres with air. User SHALL NOT
use the product in this kind of environment. Failure to comply can lead to fire and e plosive hazards.

INSERT / REMOVE BATTERY
1) Insert battery
a) lift handle
b) push down
2) Remove battery
1) lift handle
2) press button
3) pull up
1)
2)
1)
2)
3)
OPERATING INSTRUCTIONS
3) Ensure switch is off, then
place power head onto pump
stem
4) Press handle down to
lock power head
Note: Power head will not oprerate
unless locked correctly into position.
5) To remove power head,
Turn switch off, then lift handle.
1
2
3
3) Lift handle to transfer power head
from stem to stem
1) Attach power head to stem
2) Press or Release trigger to adjust flow
GENERAL OPERATION
3

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not e pressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
COMPLIANCE
FCC:
Note:
This product should be disposed of according to all applicable local and
national government environment regulations and guidelines.
For Warranty Terms and Conditions see macnaught com au
For a list of Australian Service Centres see macnaught com au
4
EUROPE: