MadgeTech DHS Specification sheet

DHS Data Logging System
DHS Data Logging System
Dry Heat Sterilization Data Logging System
Product User Guide
www. .com [e-mail]1.800.561.8187

Product Overview
The DHS Data Logging System for Dry Heat Sterilization is an all in one depyrogenation
solution that comes equipped with:
• HiTemp140-M12, High Temperature Data Logger
• 36 inch Glass Braided RTD depyrogenation probe with M12 connector and flat probe tip
• ThermoVault Max, Extreme Temperature Thermal Barrier
DHS Data Logging System
Installation Guide
Installing the Interface cable
- IFC400 or IFC406
Refer to the “Quick Start Guide” included in the package.
Installing the software
Insert the Software USB stick in an open USB port. If the autorun does not appear, locate the
drive on the computer and double click on Autorun.exe. Follow the instructions provided in
the Wizard.
Device Operation
Connecting and Starting the data logger
- Once the software is installed and running, plug the interface cable into the docking
station.
- Connect the USB end of the interface cable into an open USB port on the computer.
- The device will appear in the Connected Devices list, highlight the desired data logger.
- For most applications, select “Custom Start” from the menu bar and choose the desired
start method, reading rate and other parameters appropriate for the data logging
application and click “Start”. (“Quick Start” applies the most recent custom start options,
“Batch Start” is used for managing multiple loggers at once, “Real Time Start” stores the
dataset as it records while connected to the logger.)
- The status of the device will change to “Running”, “Waiting to Start” or “Waiting to
Manual Start”, depending upon your start method.
- Disconnect the data logger from the interface cable and place it in the environment to
measure. Note: The device will stop recording data when the end of memory is reached or the device is
stopped. At this point the device cannot be restarted until it has been re-armed by the computer.
Downloading data from a data logger
- Place the logger into the docking station.
- Highlight the data logger in the Connected Devices list. Click “Stop” on the menu bar.
- Once the data logger is stopped, with the logger highlighted, click “Download”. You will
be prompted to name your report.
- Downloading will offload and save all the recorded data to the PC.
www. .com [e-mail]1.800.561.8187

Product User Guide
Removing the Data Logger from the Thermal Barrier
1. Unscrew the lid of the thermal barrier.
3. Unscrew the HiTemp140-M12 data
logger, from the lid of the thermal barrier.
4. Slide the probe of the data logger out
from the lid of the thermal barrier.
2. Slide out the data logger and lid from
the barrier body.
www. .com [e-mail]1.800.561.8187

Product Maintenance
O-Rings
O-ring maintenance is a key factor when properly caring for the HiTemp140-M12. The
O-rings ensure a tight seal and prevent liquid from entering the inside of the device. Please
refer to the application note “O-Rings 101: Protecting Your Data”, found on the MadgeTech
website, for information on how to prevent O-ring failure.
Battery Replacement
Materials: ER1425S-HT Battery
1. Unscrew the bottom of the logger and remove the battery.
2. Place the new battery into the logger. Note the polarity of the battery.
3. Screw the cover back onto the logger.
Recalibration
The HiTemp140-M12 standard calibrations are two points at 50 1and 150 1and is
verified at 100 1.
Pricing:
Recalibration traceable to NIST $70.00
Recalibration only $40.00
Prices and specifications subject to change.
RMA Instructions
To send a device back in to MadgeTech, follow the instructions below to create an
RMA
(Return Merchandise Authorization) on the MadgeTech website:
1. Visit the Services tab select RMA Process.
2. When the web page opens, please sign in. If this is the first time, select Click here to
register an account and create one. Once signed in, click on the Make New RMA
button and fill in all the blank fields.
3. Complete the applicable fields on the form including customer Billing and Shipping
information, even if they are the same. Please see the field explanation below for a more
detailed description about questions asked in the Device Information section.
4. When all of the fields are complete, click Generate RMA.
5. Print out the confirmation page that follows containing the RMA number and
MadgeTech’s address for shipping. A Return Merchandise Authorization must be
accompanied by a copy of the RMA paperwork and shipping is prepaid by the
customer. The RMA number should be clearly marked on the outside of the package.
6. Please ship the package via UPS, FedEx, TNT, or DHL to the address listed on the
confirmation page. USPS will not ship MadgeTech data loggers.
7. A notification email will be automatically sent when MadgeTech has received the RMA.
DHS Data Logging System
www. .com [e-mail]1.800.561.8187

Temperature Sensor 36 inch Glass Braided RTD depyrogenation probe
Temperature Resolution 0.0001 1, 0.01 °C (0.02 °F)
Temperature Accuracy ±1.2 °C (-200 °C to +400 °C)
Probe Measurement Range -200 °C to +400 °C
Connector Type M12 Female, 4 Pin
Reading Rate 4 readings per second up to 1 reading every 24 hours
Memory 43,690 readings
Start Modes • Software programmable immediate start
• Delay start up to 18 months in advance
Stop Modes Manual or Timed (specific date and time)
Trigger Settings
High & Low limits may be set. Once data meets or exceed sets limits, the device
will record to memory. Bi-level start and stop triggers can also be programmed.
Users can specify the number of readings to take after the device triggers.
Readings in Trigger
Settings Mode 18,724 readings
Real Time Recording May be used with PC to monitor and record data in real time
Password Protection An optional password may be programmed into the device to restrict access
to configuration options. Data may be read out without the password.
Memory Wrap Around Yes
Battery Type 3.6V high-temperature lithium battery included; user replaceable
Battery Life 1 year typical (1 minute reading rate)
Calibration Digital calibration through software
Calibration Date Automatically recorded within device
Data Format Date and time stamped °C, °F, °R, K
Time Accuracy ±1 minute/month at 25 ºC
Computer Interface IFC400 or IFC406 USB docking station required; 125,000 baud
Operating System Compatibility XP SP3/Vista/Windows 7/Windows 8/Windows 10
Dimensions Body: 2.15 in x 0.97 in x 0.97 in (54.5 mm x 24.6 mm x 24.6 mm)
Probe: 0.10 in dia. x 36 in L (2.54 mm dia. x 76.2 mm L)
Materials Body: 316 Stainless Steel
Probe: Stainless Steel, Fiberglass, PEEK
Approvals CE
Battery Warning
WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT SHORT CIRCUIT, CHARGE, FORCE OVER
DISCHARGE, CRUSH, PENETRATE, OR INCINERATE. BATTERY MAY LEAK OR EXPLODE IF HEATED ABOVE 150ºC (302ºF).
General Specifications
Product User Guide
www. .com [e-mail]1.800.561.8187

Specifications subject to change.
See MadgeTech’s terms and conditions
Operating Environment Refer to the Time vs. Temperature Chart
IP Rating Not Rated
Barrier Materials 316 Stainless Steel, PTFE, Silicone
Enclosure Dimensions 1.75 in OD x 9.6 in L (44.45 mm OD x 243.8 mm L)
Weight 3.0 lb (1350 g)
Thermal Barrier Specifications
DHS Data Logging System
www. .com [e-mail]1.800.561.8187

Ambient
Temperature
Maximum Exposure
Time (air)
-200 °C 128 minutes
-180 °C 137 minutes
-160 °C 148 minutes
-140 °C 163 minutes
-120 °C 183 minutes
-100 °C 213 minutes
-80 °C 263 minutes
-60 °C 368 minutes
-40 °C to +140 °C Indefinitely
150 °C 601 minutes
160 °C 468 minutes
170 °C 396 minutes
180 °C 348 minutes
190 °C 313 minutes
200 °C 286 minutes
210 °C 265 minutes
220 °C 247 minutes
230 °C 233 minutes
240 °C 220 minutes
250 °C 209 minutes
260 °C 200 minutes
270 °C 192 minutes
280 °C 184 minutes
290 °C 178 minutes
300 °C 172 minutes
310 °C 166 minutes
320 °C 161 minutes
330 °C 157 minutes
340 °C 153 minutes
350 °C - 400 °C 60 minutes
Product User Guide
Time vs. Temperature Chart
www. .com [e-mail]1.800.561.8187

DOC-1322035-00 REV 1 2016.01.27
Listed specifications can be used to determine maximum allowable exposure times for the HiTemp140
with ThermoVault Max. The barrier extends the operating temperature of the logger up to, but
not exceeding, the measurement range. Please consult the measurement range of the probe for
temperatures above 250 °C (482 °F).
Both the data logger and ThermoVault Max must be at ambient temperature, approximately 25 °C (77
°F) before being placed in the extreme temperature environment. Immediately following exposure to
high temperature, the data logger should be removed from the ThermoVault Max, using appropriate
precautions, as it could be VERY hot. Failing to remove the data logger may allow heat trapped in the
ThermoVault Max to continue to heat the data logger to potentially unsafe levels.
The ThermoVault Max may take hours to fully cool down. Even if the exterior of the ThermoVault Max is
cool to the touch, the interior of the barrier and its contents may still be VERY hot.
The ThermoVault Max is primarily intended for use in dry air environments, but with the addition of the
TMAX Wet Seal Kit, the ThermoVault Max may also be used in liquids and steam environments.
If your application involves a ramp up to a temperature above 150 °C (302 °F) and/or any complex
temperature profile that isn’t a constant process, please contact MadgeTech to determine whether the
HiTemp140 with ThermoVault Max is suitable for the application.
To determine if the HiTemp140 with ThermoVault Max is suitable for the application, please provide
MadgeTech with a detailed description of your process, including temperatures, durations, ramp times
and process media such as air, steam, oil or water. If MadgeTech is unable to definitively calculate the
suitability of our product for your application, a test unit outfitted with a high temperature indicator can
be provided.
Disclaimer & Terms of Use
www. .com [e-mail]1.800.561.8187