MadgeTech Shock101-EB-5 User manual

Shock101-EB
Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289
To view the full MadgeTech product line,
visit our website at www.madgetech.com.
Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289
Battery Warning
WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT SHORT CIRCUIT, CHARGE,
FORCE OVER DISCHARGE, DISASSEMBLE, CRUSH, PENETRATE OR INCINERATE. BATTERY MAY
LEAK OR EXPLODE IF HEATED ABOVE 54°C (129°F).
Specifications subject to change.
See MadgeTech’s terms and conditions at www.madgetech.com
MadgeTech, Inc.
PO Box 50 lWarner, NH 03278
Phone [phone] lFax 603.456.2012
www.madgetech.com l[email protected]
DOC-1064035-00 REV 8 2012.02.16
Shock101-EB-5
Tri-axial +5G, Shock Data Logger with Extended Battery Life
Shock101-EB-50
Tri-axial +50G, Shock Data Logger with Extended Battery Life
Shock101-EB-100
Tri-axial +100G, Shock Data Logger with Extended Battery Life
Shock101-EB-250
Tri-axial +250G, Shock Data Logger with Extended Battery Life
Part Number Shock101-EB
Channels Shock (3 axes)
Acceleration Range
*See Table BelowAcceleration Resolution
Calibrated Accuracy
Sample Rate 512 Hz
Reading Rate 64Hz up to 5 minutes
Memory 349,525/axis
Required Interface Package IFC200
Baud Rate 115,200
Typical Battery Life 60 days
Operating Environment -20 to +54°C, 0 to 95%RH (non-condensing)
Material Anodized aluminum
Dimensions 5.5” x 5.2” x 3.2” (140mm x 132mm x 80mm)
Approvals CE
*Shock101-EB Acceleration Range, Resolution and Accuracy
Range (g) +5 +50 +100 +250
Accuracy (g) +0.2 +1 +2 +4
Resolution (g) 0.01 0.05 0.1 0.2
Product Information Card

Product Notes
Reading Intervals
The Shock101-EB samples at 512Hz and at the user specified reading rate, the device
writes the peak values (g-force) to memory.
For Example:
Axis Orientation
When the Shock101 is laying flat, with the label facing up,
the x-axis indicates left to right direction and will read ~0g
when still. The y-axis reads in a top to bottom direction and
reads ~0g when still. The z-axis reads perpendicular to the
other two axis, and will read ~1g when still.
Device Maintenance
Battery Replacement
Materials:
3/32” HEX Driver (Allen Key)
Replacement Battery (U9VL-J)
- Remove the cover from the device by unscrewing the four screws.
- Tip out the battery holder.
Note: Do not pull on the battery leads.
- Replace the 6 D-cell batteries and put the holder back into the device.
- Replace the cover taking care not to pinch the wires. Screw the enclosure back together
securely.
Note: Be sure not to over tighten the screws or strip the threads.
Recalibration
The Shock101-EB standard calibration is performed at 0g for the x-axis, 0g for the y-axis
and 1g for the z-axis.
Pricing:
Recalibration $46.00
Additional Services:
As Found Data $15.00 per channel
Prices and specifications subject to change. See MadgeTech’s terms and conditions at www.madgetech.com
To send the devices back, visit www.madgetech.com, select Services then RMA Process.
Shock101-EB Product Quick Reference Card
Installation Guide
Installing the Interface cable
- IFC200
Insert the device into a USB port. The drivers will install automatically.
Installing the software
Insert the Software CD in the CD-ROM Drive. If the autorun does not appear, locate the
drive on the computer and double click on Autorun.exe. Follow the instructions provided
in the Wizard.
Connecting the data logger
- Once the software is installed and running, plug the interface cable into the data logger.
- Click the Communication Menu, then Auto Configure Port.
- After a moment, a box will appear stating a device has been found.
- Click OK. The Device Status box will appear. Click OK.
- At this point, communications have been configured for your logger. These settings can
be found under the Communication Menu.
Note: For additional installation instructions refer to your “Data Logger & Software Operating Manual”.
Device Operation
Starting the data logger
- Click Device Menu then Start Device.
- Choose the desired start method.
- Choose the start parameters by selecting a Reading Rate suitable for your application.
- Enter in any other desired parameters and click Start.
- A box will appear stating the data logger has been started. Click OK.
- Disconnect the data logger from the interface cable and place it in the environment to
measure.
Note: The device will stop recording data when the end of memory is reached or the device is stopped. At this point the
device cannot be restarted until it has been re-armed by the computer.
Downloading data from a data logger
- Connect the data logger to the interface cable.
- Click the Device Menu then Read Device Data. This will offload all recorded data onto
the PC.
Sampled Data: Recorded Data:
Y-Axis
Z-Axis
X-Axis