Magic INMotion Super Space Scooter User manual

Age: 3+ years old
USER MANUAL
SCOOTERS
TM
TM

Super Space Scooter™ User Manual
Thank you for purchasing the Prime Super Rocket Scooter. For the
best riding experience, please read this user manual carefully
before you ride and keep this manual for reference.
Product Size: 24”L
x
32”H
Material: Steel +PVC
Tire Size: 4.5 inch
Vapor Jets’ Battery: Li 3.7V 4400mAh
Charging Time: 180 mins
Max Load: 110 lbs
Wheel: PU LED wheels
N/W: 7.7 lbs
Age: 3+years old
1
Product Specifications

Precautions
2
1. To ensure your safety, to prevent falls, imbalance, collision and
other accidents, please carefully read this manual.
2. Before riding, please check for loose parts and worn tires. If there is
any abnormality, please contact us at ser[email protected].
3. To ensure your safety and prevent damage, we recommend that
riders weigh no more than 110 lbs. (50 kg).
4. Please ride on open, flat, well-lit and dry surfaces, away from
motor vehicles and other riders.
!WARNING:
• Ages 3+
• Only one rider at a time.
• Do not exceed 110 lbs (50 kg) of weight.
• Initial setup, steering tube installation and adjustments require adult
assistance.
• Always wear safety equipment such as helmets, knee pads and elbow
pads when riding your scooter and keep the helmet’s chin strap securely
buckled.
• Always wear shoes.
• Check and secure all fasteners before every ride.
• Ride on smooth, paved surfaces away from motor vehicles.
• Avoid sharp bumps, drainage grates and sudden surface changes.
Scooter may suddenly stop.
• Avoid surfaces with sand, water, gravel, dirt and other debris. Wet
weather impairs traction, braking and visibility.
• Do not ride at night.
• Avoid excessive speed associated with downhill rides.
• Obey all local traffic and scooter riding laws and regulations.
• Watch out for pedestrians.
• Replace worn or broken parts immediately.
• This product’s water vapor jets and speaker are powered by a lithium
battery. Due to their small size, lithium batteries can easily be swallowed
by children. Ingestion of such batteries have been known to cause death.

Components
Handle Grip
Jets & Sound ON/OFF
Master ON/OFF
Charger Port
Speaker
Rod Clamp
2 Front Wheels
1 Rear Wheel
Brake
5
3
LED Headlight

Assembling your scooter
4
1. Attach handlebar to board.
Insert handlebar rod into hole
between the two front wheels,
facing the micro chip towards the
back of the scooter. Push down
until you hear a snapping sound.
2. Adjust handlebar’s height.
Press and hold on silver lock
button and pull handlebar to
desired height.
3. Fill jets with water.
Tilt scooter up 90 degrees. Push
down onto water insert button,
and pour no more than 3 ounces
of distilled water onto water insert
button (pictured).
Water goes here

5
2. Push master ON/OFF
to turn on the scooter. This allows
you to turn on the jets, sound
effects and LED headlight.
1. Charge your scooter
by plugging charger into charger
port. It takes 180 minutes to fully
charge.
3. Turn on jets, sounds and LED
headlight by pressing on the
secondary ON/OFF button on the
handlebar.
4. Activate LED wheels
by simply riding your scooter.
Master ON/OFF
Jets & Sounds
ON/OFF
Using Your Scooter
Charger port

6
Taking apart your scooter
5. Step on back brake to brake,
lightly to slow to a stop, and more
forcefully for an abrupt stop.
1. Power off
by pushing the master ON/OFF
Step on brake
2. Remove handlebar.
Simultaneously push and hold two
black lock buttons located
between the front wheels, then
pull out handlebar from above.
Push from
both sides

For all questions regarding this product, contact us at:
[email protected]