Magner L-1500 User manual

PRELIMINARY
L
LL
L-
--
-1500
15001500
1500
User’s Manual
MAGNER
MAGNERMAGNER
MAGNER

< Contents >
1. Safety Instruction
2. Appearance
3. Structure
4. Display Description
5. Operation Panel
6. Operation
7. Error Code
8. Accessories & Options
9. Specification
10. Sensor Location
L-1500 User’s Manual 2

1. Safety Instruction
Never disassemble the machine except the trained person.
Be careful not to pinch your finger when closing the Upper & Rear
Cover.
Use the voltage between AC100V and AC240V
Turn off the machine during cleaning, and do NOT use flammable gas
spray
for
cleaning
.
1) CAUTION
spray
for
cleaning
.
2) WARNING
Do not touch the machine or the power cable with a wet hand.
Do not operate the machine, if smoke or strange smell is detected from
the machine. In this case, please contact your local distributor
Always keep clothes, hairs and fingers out of the feed hopper area
UV RADIATION!! Eye and skin protection during servicing
3L-1500 User’s Manual

2. APPEARANCE
NO
NAME
NO
NAME
NO
NAME
NO
NAME
①Hopper Guide ⑨Stacker
②Upper Cover ⑩Thickness Dial
③Lower Cover ⑪Upper Rear Cover
④Carrying Handle ⑫Interface Connector
⑤Hopper ⑬Inlet
⑥LCD Display ⑭Power Switch
⑦Operation Panel Lower Rear Cover
⑧Cover Open Button
4L-1500 User’s Manual

3. Structure
1) How to open upper cover
Press open button and lift it to open the upper cover.
2) How to close upper cover
Lift the upper cover a little by left hand and pull the lift lever forward and then fall down
the upper cover slowly. Be careful not to pinch your finger.
3) How to open rear cover
Hold and lift the lever to open the rear cover.
5L-1500 User’s Manual

Operation mode
Operation modeOperation mode
Operation mode
Currency
CurrencyCurrency
Currency
Auto or Manual Start
Auto or Manual StartAuto or Manual Start
Auto or Manual Start
Total Value
Total ValueTotal Value
Total Value
ADD
ADDADD
ADD
Batch
BatchBatch
Batch
Number of notes on Stacker
Number of notes on StackerNumber of notes on Stacker
Number of notes on Stacker
Speed
SpeedSpeed
Speed
Number of notes on Re ect
Number of notes on Re ectNumber of notes on Re ect
Number of notes on Re ect
4. Display Description
REJECT
COUNT
€
€€
€TOTAL
MIX AUTO
P100 S1000 ADD
NAME FUNCTION
COUNT Count all currencies without recognition and detection.
MIX Count all denomination of selected currency.
SP Sort out the same denomination of first inserted note or
specific denomination
V-SP Sort out the old and new version of specific denomination.
FACE Separate front side or rear side of the notes of first inserted
note or specific denomination
ORIENT Separate different direction notes of first inserted note or
specific denomination
6L-1500 User’s Manual

1)
1) 1)
1) Number Key
Number KeyNumber Key
Number Key
5. Operation Panel
Number Key is used for Batch Key and also when press and hold down each key, user can enter each function.
NO NAME FUNCTION NO NAME FUNCTION
①
$Select USD, if available
⑧
SAVE Save the Function Setting in Memory.
②
€Select EURO, if available
⑨
BAT Select Batch Number
③
LC
Select
Local
Currency
0
ADD
Accumulate
all
Counted
Notes
.
NAME FUNCTION NAME FUNCTION
CURRENCY Select Currency START/STOP Counting stop or restart.
MODE Select Different Operation Mode RED LED Notes on the Rejecter
FUNCTION Enter User Mode GREEN LED Notes on the Stacker
CLEAR (C) Exit the menu and clear errors.
2)
2)2)
2) Hot Key
Hot KeyHot Key
Hot Key
7L-1500 User’s Manual
③
LC
Select
Local
Currency
0
ADD
Accumulate
all
Counted
Notes
.
⑤
ERROR Display the Error Information. UP Enter Service Mode. (Password Necessary)
⑥
TOTAL Show the Denomination Information. DOWN Enter Technical Mode (Password Necessary)
⑦
PRINT Print out the Denomination Information

1) USD Key
Press and hold down Key and select USD Currency. (Depending on the Currency, this key may not work)
2) EUR Key
Press and hold down Key and select EUR Currency. (Depending on the Currency, this key may not work)
3
)
Local Currency Key
1
$
2
€
€€
€
3) Details of Number
3) Details of Number 3) Details of Number
3) Details of Number Key
KeyKey
Key
3
)
Local Currency Key
Press and hold down Key and select Local mode
4) ERROR Key
Press and hold down Key and select ERROR report
It displays the detailed information of Unfit & rejected notes
3
LC
8L-1500 User’s Manual
5
ERROR

5) TOTAL Key
Press and hold down Key and select Total Value List
It displays the denomination information of counted notes
6) PRINT Key
Press and hold down Key and select Print
It prints out the denomination information of counted notes.
In addition, as an option, Serial Number of banknote can be printed out
7
PRINT
6
TOTAL
7) SAVE Key
Press and hold down Key and save the data in User or Service or Technical Mode
It saves the changed setting in memory.
8) BAT Key
Press and hold down Key and select BATCH Number
It selects Batch number which was selected already (10, 20, 50, 100) by
pressing Key each time.
8
SAVE
9L-1500 User’s Manual
9
BAT
9
BAT

9) ADD Key
Press and hold down Key and select ADD Mode
It accumulates all counted notes.
10) SERVICE Mode Key
Press and hold down Key and select SERVICE Mode
Password is necessary, and strongly recommend to use only with Service Engineer.
0
ADD
11) TECHNICAL Mode Key
Press and hold down Key and select TECHNICAL Mode
Password is necessary, and strongly recommend to use only with Service Engineer.
10L-1500 User’s Manual

6. OPERATION
6-1. Self Diagnosis
Loading Software… Loading Software…
MAIN : LX7MA-EU1-F1-01
IMAGE : LX7IMG-EU1-01-01
- After turning on the power of machine, the self diagnosis will be done as follows;
Checking Sensors & Motors …
1) Software Loading 2) During Software Loading, each software version will
be displayed.
3) After software loading successfully, Sensor & Motor
function will be checked.
4) If everything is OK, “Test OK” message will show up.
However, if error is happened during initializing, the
related error message will show up.
Test OK
MAIN : LX7MA-EU1-F1-01
IMAGE : LX7IMG-EU1-01-01
MAIN : LX7MA-EU1-F1-01
IMAGE : LX7IMG-EU1-01-01
11L-1500 User’s Manual

6-2. Denomination Mode
1) USD Mode
Press key and select USD($) currency.
Press key and select Operation Mode.
In this mode, it can recognize and detect USD currency.
(Depending on the Currency, this mode may not work)
2) EURO Mode
Press key and select EUR(€) currency.
CURRENCY
CURRENCY
MODE
Press key and select Operation Mode.
In this mode, it can recognize and detect EUR currency.
(Depending on the Currency, this mode may not work)
3) Local Mode
Press key and select LC (TL,RUB, GBP, MXN,SAR, INR etc) currency.
Press key and select Operation Mode.
In this mode, it can recognize and detect Local currency.
CURRENCY
MODE
MODE
12L-1500 User’s Manual

6-3. Operation Mode
1) Count Mode
Press key and select Count Mode.
It count the all currencies without recognition and detection.
2) MIX Mode
Press key and select Mix Mode.
MODE
MODE
Press key and select Mix Mode.
It count the all denomination of selected currency.
3) SP Mode (SP- Denomination Mode)
Press key and select SP Mode.
It sorts out the same denomination as first inserted note or
pre-selected denomination by UP[△]/DOWN[▽] Key.
MODE
MODE
13L-1500 User’s Manual

4) FACE Mode (FACE-DEN Mode)
Press key and select FACE Mode.
It separates front side or rear side of the notes of all
denominations or first inserted note by UP[△]/DOWN[▽] Key.
(Depending on the Currency, this mode may not work)
5) ORIENT Mode (ORIENT-DEN Mode)
Press key and select ORIENT Mode.
MODE
MODE
It separates different direction notes of all denominations or first
inserted note by UP[△]/DOWN[▽] Key.
(Depending on the Currency, this mode may not work)
6) FIT Mode (FIT-DEN Mode)
Press key and select FIT Mode.
It separates Fit notes of all denominations or first inserted note
by UP[△]/DOWN[▽] Key.
(Depending on the Currency, this mode may not work)
14L-1500 User’s Manual
MODE

7) OCR Mode: Option
Press key and select OCR Mode.
It prints out the serial number of all denominations
(Depending on the Currency, this mode may not work)
The Printing Option is available in User Mode
MODE
15L-1500 User’s Manual

6-4. User Mode
1. Press Key to enter User Mode
2. Move the next content by pressing “UP/DOWN” (△/▽) Key (“*” mark is showing the present selected
content), and then press Key to choose the content or press Key to exit the mode.
3. After choosing the content, the target content will be highlighted in yellow color.
4. After changing the data, press the Key to save them, otherwise the data will remain unchanged
FUNCTION
FUNCTIONFUNCTION
FUNCTION
START
STARTSTART
START
STOP
STOPSTOP
STOP
NO
NONO
NO CONTENTS
CONTENTSCONTENTS
CONTENTS DESCRIPTION
DESCRIPTIONDESCRIPTION
DESCRIPTION DEFAULT SETTING
1 REJECT SIZE Set Maximum Reject note capacit from 10 to 100 50
2 EXT-DEVICE Set the External Device between External Displa and Printer
(Refer to the detail setting) EXT-DISPLAY1
8
SAVE
C
3 DENSITY Set the Densit Level from -4 to 9 or AUTO for Count Mode ONLY.
Lower value is less sensitive and higher value is more sensitive setting AUTO
4 LANGUAGE Set the Language shown in Displa ENGLISH
5 CF DISP Set the “CF” displa function as ON or OFF ON
6 REJECT DISP Set the reject No. displa function as ON or OFF ON
7 COUNT Set the counting start function as Automatic or Manual AUTO
8 SPEED Set the counting speed of machine 1000
9 USER I/F Set the PC Interface NONE or USER1 NONE
10 FIT SETTING Set the Fitness level setting (Refer to the detail setting) CB Standard
16L-1500 User’s Manual

*1. EXT
EXTEXT
EXT-
--
-DISPLAY1
DISPLAY1 DISPLAY1
DISPLAY1 : ON
: ON: ON
: ON
2. EXT-DISPLAY2 : OFF
3. OCR PRINT : MANUAL
4 .
. .
. PRINTER : OFF
5. BAUD RATE : 115,200 bps
6. PAPER SIZE : 2 inch
7. PRINTING No : 1 pcs
5. Detailed Setting of EXT-DEVICE & FIT SETTING
1) EXT-DEVICE
*1. EXT-DISPLAY1 : ON
2. EXT-DISPLAY2 : OFF
3. OCR PRINT : MANUAL
4. PRINTER : OFF
5. BAUD RATE : 115,200 bps
6. PAPER SIZE : 2 inch
7. PRINTING No : 1 pcs
EXT
EXTEXT
EXT-
--
-DEVICE
DEVICEDEVICE
DEVICE
- EXT-DISPLAY 1: 1-Line External Display ON or OFF
-
EXT
-
DISPLAY
2: 2
-
Line External Display ON or
OFF
UP[
UP[UP[
UP[△
△△
△] DOWN[
] DOWN[] DOWN[
] DOWN[▽
▽▽
▽] SEL[START/STOP]
] SEL[START/STOP]] SEL[START/STOP]
] SEL[START/STOP]
SAVE[KEY8] EXIT[C]
SAVE[KEY8] EXIT[C]SAVE[KEY8] EXIT[C]
SAVE[KEY8] EXIT[C]
EXT
EXTEXT
EXT-
--
-DEVICE
DEVICEDEVICE
DEVICE
START
STOP
C
USER MODE
USER MODEUSER MODE
USER MODE
START
STOP
C
UP[
UP[UP[
UP[△
△△
△] DOWN[
] DOWN[] DOWN[
] DOWN[▽
▽▽
▽] SEL[START/STOP]
] SEL[START/STOP]] SEL[START/STOP]
] SEL[START/STOP]
SAVE[KEY8] EXIT[C]
SAVE[KEY8] EXIT[C]SAVE[KEY8] EXIT[C]
SAVE[KEY8] EXIT[C]
-
EXT
-
DISPLAY
2: 2
-
Line External Display ON or
OFF
- OCR PRINT: AUTO or MANUAL
- Printer Set: ON or OFF
- Baud Rate: 9,600 ~ 115,200 bps (Default Setting 115,200)
- Paper Size: 2 or 3 inch (Default Setting 2 inch)
- Printing No: 1 ~ 3 pcs (Default Setting 1 pc)
1. REJECT : 50
*2. EXT-DEVICE : EXT-DISPLAY1
3. DENSITY : AUTO (COUNT ONLY)
……………………………………..
UP[
UP[UP[
UP[△
△△
△] DOWN[
] DOWN[] DOWN[
] DOWN[▽
▽▽
▽] SEL[START/STOP]
] SEL[START/STOP]] SEL[START/STOP]
] SEL[START/STOP]
- The details setting for the Highlight can be changed by pressing UP[△]/DOWN[▽] Key
- If Printer is OFF, the BAUD RATE & PAPER SIZE & PRINTING No will be inactivated
- Press Key to save the data before exit the setting.
8
SAVE
17L-1500 User’s Manual

2) FIT SETTING
----------------------------
7. COUNT : AUTO
8. SPEED : 1200
9. USER I/F : NONE
*
**
* 10. FIT SETTING : MANUAL
USER MODE
USER MODEUSER MODE
USER MODE
UP[
UP[UP[
UP[△
△△
△] DOWN[
] DOWN[] DOWN[
] DOWN[▽
▽▽
▽] SEL[START/STOP]
] SEL[START/STOP]] SEL[START/STOP]
] SEL[START/STOP]
START
STOP
1. CB STANDARD: OFF
FIT SETTING
FIT SETTINGFIT SETTING
FIT SETTING
FIT SETTING
FIT SETTINGFIT SETTING
FIT SETTING
----------------------------
7. COUNT : AUTO
8. SPEED : 1200
9. USER I/F : NONE
*
**
* 11. FIT SETTING : CB STANDARD
USER MODE
USER MODEUSER MODE
USER MODE
UP[
UP[UP[
UP[△
△△
△] DOWN[
] DOWN[] DOWN[
] DOWN[▽
▽▽
▽] SEL[START/STOP]
] SEL[START/STOP]] SEL[START/STOP]
] SEL[START/STOP]
C
1. CB STANDARD: OFF
* 2. MANUAL: ON
2. MANUAL: ON2. MANUAL: ON
2. MANUAL: ON
Denom Soil Tear Corner Hole Tape
5 5 5 5 5 5
10 5 5 5 5 5
20 5 5 5 5 5
50 5 5 5 5 5
100 5 5 5 5 5
200 5 5 5 5 5
500 5 5 5 5 5
UP[
UP[UP[
UP[△
△△
△] DOWN[
] DOWN[] DOWN[
] DOWN[▽
▽▽
▽]
] ]
] SEL[START/STOP]
SEL[START/STOP]SEL[START/STOP]
SEL[START/STOP]
SAVE[KEY8]
SAVE[KEY8] SAVE[KEY8]
SAVE[KEY8] EXIT[C]
EXIT[C]EXIT[C]
EXIT[C]
* 1. CB STANDARD: ON
1. CB STANDARD: ON1. CB STANDARD: ON
1. CB STANDARD: ON
2. MANUAL: OFF
Denom Soil Tear Corner Hole Tape
5 5 5 5 5 5
10 5 5 5 5 5
20 5 5 5 5 5
50 5 5 5 5 5
100 5 5 5 5 5
200 5 5 5 5 5
500 5 5 5 5 5
UP[
UP[UP[
UP[△
△△
△] DOWN[
] DOWN[] DOWN[
] DOWN[▽
▽▽
▽]
] ]
] SEL[START/STOP]
SEL[START/STOP]SEL[START/STOP]
SEL[START/STOP]
SAVE[KEY8]
SAVE[KEY8] SAVE[KEY8]
SAVE[KEY8] EXIT[C]
EXIT[C]EXIT[C]
EXIT[C]
- The details setting for the Highlight can be changed by pressing UP[△]/DOWN[▽] Key
- Press Key to save the data before exit the setting.
8
SAVE
18L-1500 User’s Manual

1. CB STANDARD: OFF
* 2. MANUAL: ON
2. MANUAL: ON2. MANUAL: ON
2. MANUAL: ON
Denom Soil Tear Corner Hole Tape
5 5 5 5 5 5
10 5 5 5 5 5
20 5 5 5 5 5
50 5 5 5 5 5
100 5 5 5 5 5
200 5 5 5 5 5
500 5 5 5 5 5
FIT SETTING
FIT SETTINGFIT SETTING
FIT SETTING
UP[
UP[UP[
UP[△
△△
△] DOWN[
] DOWN[] DOWN[
] DOWN[▽
▽▽
▽]
] ]
] SEL[START/STOP]
SEL[START/STOP]SEL[START/STOP]
SEL[START/STOP]
SAVE[KEY8]
SAVE[KEY8] SAVE[KEY8]
SAVE[KEY8] EXIT[C]
EXIT[C]EXIT[C]
EXIT[C]
- Each Fit Setting Level can be set from 0 ~ 10
- 0 mean OFF, 10 means the most sensitive setting
- The detail setting of each level can be adjusted in Technical Mode
FIT SETTING
FIT SETTINGFIT SETTING
FIT SETTING
* 1. CB STANDARD: ON
1. CB STANDARD: ON1. CB STANDARD: ON
1. CB STANDARD: ON
2. MANUAL: OFF
Denom Soil Tear Corner Hole Tape
5 5 5 5 5 5
10 5 5 5 5 5
20 5 5 5 5 5
50 5 5 5 5 5
100 5 5 5 5 5
200 5 5 5 5 5
500 5 5 5 5 5
FIT SETTING
FIT SETTINGFIT SETTING
FIT SETTING
UP[
UP[UP[
UP[△
△△
△] DOWN[
] DOWN[] DOWN[
] DOWN[▽
▽▽
▽]
] ]
] SEL[START/STOP]
SEL[START/STOP]SEL[START/STOP]
SEL[START/STOP]
SAVE[KEY8]
SAVE[KEY8] SAVE[KEY8]
SAVE[KEY8] EXIT[C]
EXIT[C]EXIT[C]
EXIT[C]
- CB Standard is setting for Central Bank Test Setting Standard
- It is fixed setting, but the detail setting of each level can be adjusted
in Technical Mode
- After CB Standard is ON, the Manual Setting will be inactivated
19L-1500 User’s Manual

NO
NONO
NO DISPLAY
DISPLAYDISPLAY
DISPLAY CAUSE OF ERROR
CAUSE OF ERRORCAUSE OF ERROR
CAUSE OF ERROR POSSIBLE
POSSIBLEPOSSIBLE
POSSIBLE SOLUTION
SOLUTIONSOLUTION
SOLUTION
1 Doubl Double notes - Check the condition of rejected note as Double
- Check the gap between Feed and Reverse Roller
2 Chain Chain notes
- Check the condition of rejected note as Chain
- Check the gap between Feed and Reverse Roller
- Check the condition of Encoder Sensor in Service Mode
3 ASN Skew notes - Check the condition of rejected note as Skew
- Check the gap between Feed and Reverse Roller
4
Half
Half
notes
- Check the rejected note condition as Half
-
Check the condition of Count Sensors in Service Mode
7. Error Code
4
Half
Half
notes
-
Check the condition of Count Sensors in Service Mode
5 Face & Ort Different Face or Orientation - Check the rejected note condition as Face & Ort
- Adjust CIS Sensor
6 Denom Different Denomination - Check the rejected note condition as Denom
- Adjust CIS Sensor
7 Issue Different Issue - Check the rejected note condition as Issue
- Adjust CIS Sensor
8 UV UV Error
- Check the condition of rejected notes
- Restart counting operation
9 MG MG Error
10 IR IR Error
20L-1500 User’s Manual