Mainstays CONRAD MS17-D4-1007-16 User manual

1PB
model# MS17-D4-1007-16
model# MS17-D4-1007-17
model# MS18-D1-1007-06
model# MS18-D1-1007-07
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
black
white
gray
navy
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
CONRAD DESK WITH HUTCH

2
TOP PANEL
LEFT PANEL
RIGHT PANEL
PARTITION PANEL
BOTTOM PANEL
BACK PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
BOTTOM ASSEMBLY
BOTTOM RAIL
A
B
C
D
E
F
G
H
I
J
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
Hammer Flat Head Screwdriver Phillips Head Screwdriver
PARTS LIST

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Cam
x9
3. Medium Bolt
x2
4. Allen Wrench
x1
1. Large Bolt
x8
2. Small Bolt
x8
6. Cam Bolt
x9

4
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
7. Flat Head Screw
x13
8. Wood Dowel
x4
9. Short Pan Head Screw
x1
10. Long Pan Head
Screw
x1
11. Wall Strap
x1
12. Wall Anchor
x1
13. Washer
x2

4 5
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

6
x4x1
6. Cam Bolt
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 5 for instructions on how to use the cam lock system.
STEP 1
8. Wood
Dowel
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

6 7
x4
STEP 2
1. Refer to page 5 for instructions on how to use the cam lock system.
5. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

8
x4x5 x5x1
STEP 3
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Refer to page 5 for instructions on how to use the cam lock system.
3. Make sure the screws go through the pre-drilled holes properly.
4. Do not over tighten screws.
5. Cam 7. Flat Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
6. Cam Bolt8. Wood
Dowel

8 9
x2 x9
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
STEP 4
8. Wood
Dowel
7. Flat Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10
x2 x1x8
STEP 5
1. Make sure the bolts go through the pre-drilled holes properly.
2. Do not over tighten bolts.
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
1. Large Bolt 2. Small Bolt 4. Allen
Wrench