Mainstays GSB3321019-3 User manual

TM
MAINSTAYS
Industrial 4 Drawer Dresser
Stock # GSB3321019-3
20-25minutes
approx assembly time
Two adults
Assembly required
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
For assistance with assembly or installation, parts and customer
service , call 1-888-568-3818 Monday-Friday 8:30am-5:30pm
PST (U.S)
Email: [e-mail]
Working hour: Mon.-Fri., 8:30am - 5:30pm Pacific Standard
Time.
Stock # GSB3321019-3
Lot Number : _________
Date Purchased ______/____/_____
Manufactured By : Young Chain Company Limited
Binh Duong Province, Vietnam
TEL : [phone]
EMAIL : [e-mail]
We are available to assist you Monday-Friday
From 8:30am-5:30pm PST (US)
MAXIMUM LOAD 44 LB (20 KG)
DRAWER MAXIMUM LOAD
10 LBS (4.54 KG)
Review your purchases, thank you!
Share your feedback to help other shoppers
Link for this product is as below:
www.walmart.com/ip/715597902

TM
MAINSTAYS
Industrial 4 Drawer Dresser
Stock # GSB3321019-3
Manufactured By : Young Chain Company Limited
Binh Duong Province, Vietnam
TEL : [phone]
EMAIL : [e-mail]
We are available to assist you Monday-Friday
From 8:30am-5:30pm PST (US)
Important Safety Information
Please read all instructions carefully before assembling this furniture.
For your safety, assembly by two or more adults is strongly recommended.
Use only vendor-supplied hardware to assemble this item. Using unauthorized hardware
could jeopardize the structural integrity of the item.
Hardware may loosen overtime. Periodically check that all connections are tight.
NOTICE: To prevent injury and property damage from unexpected tipping of furniture, we highly
recommend installation of the anti-tip kit included with this product.
General Information, Tips & Tricks
Remove all parts and hardware from the box. Place all items on a carpeted or scratch-free work
surface, as this will avoid damaging parts during assembly.
The shipping box provides an ideal work surface.
To avoid accidentally discarding small parts or hardware, do not dispose of any packaging or
contents of the shipping carton until assembly is complete.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The use of power tools for assembly is not recommended. Power tools can damage the hardware
and/or split the wood
Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may
cause the bolts to misalign during assembly.
Safety and care
It is advisable to dust frequently with a clean, soft, dry, lint-free cloth. Clean the surface by
rubbing in the direction of the grain.
Do not place furniture in direct sunlight and keep furniture at least 60 cm / 2 ft from heat
sources to avoid fading.
DO NOT USE POWER DRILL / DRIVERS FOR INSERTING
SCREWS / BOLTS AS THIS COULD DAMAGE THE UNIT.
ONLY USE HAND SCREWDRIVERS.
Help and support
For assistance with assembly or installation, parts and customer service ,
call 1-888-568-3818 Monday-Friday 8:30am-5:30pm PST (U.S)
Email: [e-mail]
Working hour: Mon.-Fri., 8:30am - 5:30pm Pacific Standard Time.

PARTS
ATOP
×1
BBASE
×1
C D
E F G H
IJK L
M
SIDE PANEL
×2
BACK PANEL
×1
MIDDLE BAR
×1
SIDE METAL
FRAME ×2
CROSS BAR
×2
DRAWER FRONT
PANEL ×4
DRAWER LEFT
PANEL ×4
DRAWER RIGHT
PANEL ×4
DRAWER BACK
PANEL ×4
DRAWER BOTTOM
PANEL ×4
SUPPORT BAR
×4
VERIFY THAT ALL PARTS ARE LISTED BEFORE BEGINNING Page 3

CAM LOCK
×46+1
CAM BOLT
×46+1
DOWEL
×20+1
BUCKLE
×8
FLAT HEAD
SCREW ×24+1
ROUND HEAD
SCREW ×16+1
STICKER PVC
×16+1
HANDLE
×4
ALLEN WRENCH
×1
SMALL BOLT
×8
SHORT BOLT
×8+1
SPRING WASHER
×20+1
LONG BOLT
×12+1
FLAT WASHER
×20+1
BRACKET
×2
2 3 41
6 7 85
10 11 129
1413
ANTI-TIP CABLE
×1
LONG SCREW
×1
SHORT SCREW
×1
PLASTIC ANCHOR
×1
VERIFY THAT ALL PARTS ARE LISTED BEFORE BEGINNING Page 4
HARDWARE LIST
Anti-tip Hardware
TOOLS NEEDED
FOR ASSEMBLY
(NOT PROVIDED)
15

1. Screw the cam bolt into the predrilled panel. The cam bolt should be tightened
so no threads are visible.
2. The larger ring of the cam should touch the panel.
3. Insert the cam lock into the predrilled hole in the panel. Arrow faces the
outside of the panel.
4. Connect the previously tightened cam bolt with the panel connected into the
cam lock.
5. Using a flat head screw driver, turn the cam lock halfway clockwise to secure
the cam bolt.
6. FAILURE TO PROPERLY SECURE THE CAM LOCK AND CAM BOLT COULD RESULT
IN PRODUCT INSTABALITY AND FAILURE.
Page 5
CAM FASTEN SYSTEM EXAMPLE
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
RING SHOULD
TOUCH THE BOARD
1 2 3
45 6

Page 6
11. Align the SIDE METAL FRAME ( F ) with the CROSS BAR ( G ) and then insert
the SIDE METAL FRAME ( F ) into the CROSS BAR ( G ).
2. And then use the ALLEN WRENCH ( 10 ) to secure the FLAT WASHER ( 13 ),
SPRING WASHER ( 12 ) and SHORT BOLT ( 11 ) to attach the SIDE METAL FRAME
( F ) with the CROSS BAR ( G ). Tighten the SHORT BOLT ( 11 ).
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
ALLEN WRENCH
×1
SHORT BOLT
×8
SPRING WASHER
×8
FLAT WASHER
×8
10 11 12 13
ASSEMBLY

Page 7
21. Align the pre-assembled metal feet to the corresponding hole of the BASE ( B ).
2. And then use the ALLEN WRENCH ( 10 ) to secure the FLAT WASHER ( 13 ),
SPRING WASHER ( 12 ) and LONG BOLT ( 14 ) to attach the SIDE METAL FRAME
( F ) and CROSS BAR ( G ) to the BASE ( B ). Tighten the LONG BOLT ( 14 ).
** Note: Use the adjustable levelers to level the Industrial 4 drawer dresser if needed.
ASSEMBLY
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
ALLEN WRENCH
×1
SPRING WASHER
×12
FLAT WASHER
×12
10 12 13
LONG BOLT
×12
14

31. Turn over the BASE ( B ) like the figure shown below.
2. Insert the CAM BOLT ( 1 ) into the corresponding hole of the BASE ( B ). And use a
hand screwdriver to tighten the CAM BOLT ( 1 ) clockwise.
ASSEMBLY
Page 8
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
CAM BOLT
×8
1

41. Place the TOP ( A ) face down on a smooth soft surface. The side with the holes
should be facing up.
2. Insert the CAM BOLT ( 1 ) into the corresponding hole of the Top ( A ). And use a
hand screwdriver to tighten the CAM BOLT ( 1 ) clockwise.
ASSEMBLY
Page 9
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
CAM BOLT
×8
1

51. Place the SIDE PANEL ( C ) face down on a smooth soft surface. The side with
the holes and glides should be facing up.
2. Insert the CAM BOLT ( 1 ) into the corresponding hole of the SIDE PANEL ( C ).
And use a hand screwdriver to tighten the CAM BOLT ( 1 ) clockwise.
** Repeat these same steps for another SIDE PANEL ( C ).
ASSEMBLY
Page 10
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
CAM BOLT
×10
1

Insert the DOWEL ( 3 ) all the way into the corresponding hole of the SIDE PANEL ( C ).
** Repeat these same steps for another SIDE PANEL ( C ).
ASSEMBLY
Page 11
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
DOWEL
×8
3
6

Insert the DOWEL ( 3 ) all the way into the corresponding hole of the BACK PANEL ( D ).
ASSEMBLY
Page 12
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
DOWEL
×8
3
7

81. Align the corresponding hole of the BACK PANEL ( D ) and SIDE PANEL ( C ) as figure
shown below.
2. Insert the CAM LOCK ( 2 ) into the corresponding hole ( the direction of the notch is
aligned with the cam bolt as the figure shown below).
3. Use a hand screwdriver to turn the CAM LOCK ( 2 ) clockwise to secure the cam bolt.
ASSEMBLY
Page 13
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
CAM LOCK
×3
2
Make sure edge of both panel
align and even
The direction of the
notch of the cam
lock is aligned with
the cam bolt.

91. Align the corresponding hole of the MIDDLE BAR ( E ) as figure shown below.
2. Align the corresponding hole of the MIDDLE BAR ( E ) and BACK PANEL ( D ) into
the corresponding hole of SIDE PANEL ( C ) as figure shown below .
3. Insert the CAM LOCK ( 2 ) into the corresponding hole ( the direction of the notch is
aligned with the cam bolt as the figure shown below).
4. Use a hand screwdriver to turn the CAM LOCK ( 2 ) clockwise to secure the cam bolt.
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
CAM LOCK
×7
2
ASSEMBLY
Page 14
Make sure edge of both panel
align and even
The direction of the
notch of the cam
lock is aligned with
the cam bolt.

Page 15
10 1. Insert the SIDE PANEL ( C ) AND BACK PANEL ( D ) into the corresponding hole of
TOP ( A ).
2. Place the CAM LOCK ( 2 ) into the corresponding hole ( the direction of the notch
of the cam locks align with the cam bolt ).
3. Use a hand screwdriver to turn the CAM LOCK ( 2 ) clockwise to secure the cam bolt.
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
CAM LOCK
×8
2
ASSEMBLY
Attention: Where holes of
Middle bar oriented should
assemble Base. Assemble Top
on the opposite side.
The direction of the
notch of the cam
lock is aligned with
the cam bolt.
C

Page 16
11 1. Insert the SIDE PANEL ( C ) and BACK PANEL ( D ) into the corresponding hole of
BASE ( B ).
2. Place the CAM LOCK ( 2 ) into the corresponding hole ( the direction of the notch
of the cam locks align with the cam bolt ).
3. Use a hand screwdriver to turn the CAM LOCK ( 2 ) clockwise to secure the cam bolt.
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
CAM LOCK
×8
2
ASSEMBLY
Attention: Where holes of
Middle bar oriented should
assemble Base. Assemble Top
on the opposite side.
The direction of the
notch of the cam
lock is aligned with
the cam bolt.

Page 17
12 1. Place the DRAWER FRONT PANEL ( H ), DRAWER LEFT PANEL ( I ), DRAWER RIGHT
PANEL ( J ) and DRAWER BACK PANEL ( K ) face down on a smooth soft surface.
The side with the holes should be facing up.
2. Insert the CAM BOLT ( 1 ) into the corresponding hole of DRAWER FRONT PANEL ( H )
as shown in below figures.
3. Use a hand screwdriver to tighten the CAM BOLT ( 1 ) clockwise.
** Repeat all 1-4 steps for all 4 drawers.
ASSEMBLY
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
CAM BOLT
×20
1

Page 18
13 Insert the DOWEL ( 3 ) all the way into the corresponding hole of the SUPPORT BAR ( M ).
** Repeat all steps for all 4 drawers.
ASSEMBLY
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
DOWEL
×4
3

M
14 1. Align and insert the DRAWER LEFT PANEL ( I ) and DRAWER RIGHT PANEL ( J ) into
the corresponding hole of DRAWER FRONT PANEL ( H ).
2. Align and insert the SUPPORT BAR ( M ) into the corresponding hole of DRAWER
FRONT PANEL ( H ).
3. Insert the CAM LOCK ( 2 ) into the corresponding hole ( the direction of the notch is
aligned with the cam bolt as the figure shown below).
4. Use a hand screwdriver to turn the CAM LOCK ( 2 ) clockwise to secure the cam bolt.
** Repeat all steps for all 4 drawers.
Page 19
ASSEMBLY
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited
J
CAM LOCK
×20
2
Groove should
align and even
H
The direction of the
notch of the cam
lock is aligned with
the cam bolt.

M
L
15 1. Align and insert the DRAWER BOTTOM PANEL ( L ) to the groove of DRAWER LEFT
PANEL ( I ) and DRAWER RIGHT PANEL ( J ). All the way until into the groove of the
DRAWER FRONT PANEL ( H ).
** Repeat all steps for all 4 drawers.
Page 20
ASSEMBLY
Please call for replacement parts or assistance: 1-888-568-3818
Young Chain Company Limited