Mainstays MS62025004001 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2022-05-17 Rev. 0001-A
A justable Desk
Mo el # MS62025004001
ADULT ASSEMBLY REQUIRED
If you have any questions regar ing assembly or if parts are missing, DO NOT return this item to the
store where it was purchase . Please call our customer service number an have your instructions
an parts list rea y to provi e the mo el name, part name or factory number:
866-942-5362
Pacific Stan ar Time: 8:30 a.m. - 4:30 p.m., Mon ay - Fri ay
Or visit our web site 24 hours a ay, 7 ays a week for pro uct assistance at
www.whalenstyle.com
Or e-mail your request to pa ts@whalenfu nitu e.com
LOT NUMBER:
DATE PURCHASED: / /
Option
al
L
-
shape
Corner Desk
Optional
Extra Long
Desk

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Adjustable Desk
MODEL # MS62025004001
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton before
discarding. Remove all parts from carton and separate into groups as indicated on part
list. Please ensure all parts are included prior to assembly. Use of power tools to
complete assembly is not recommended.
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 90.8 kg / 200 lb.
MAXIMUM LOAD 22.7 kg / 50 lb.

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Return Top Panel (Qty. 1) B- Middle Tier Top Panel (Qty. 1)
C- Desk Top Panel (Qty. 1) D- Fixed Shelf (Qty. 2)
E- Side Frame (Qty. 2) F- Middle Tier Left Frame (Qty. 1)
G- Middle Tier Right Frame (Qty. 1) H- Desk Front Stretcher (Qty. 1)
I- Desk Back Stretcher (Qty. 1) J- Desk Bottom Stretcher (Qty. 1)

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
K- Return Front Stretcher (Qty. 1) L- Return Back Stretcher (Qty. 1)
M- Return Bottom Stretcher (Qty. 1) N- X Crossbar (Qty. 2)
(1) 1/4" x 15mm Bolt (2) 1/4" x 30mm Bolt (3) 5/32" x 8mm Bolt
(Qty. 5+1 extra) (Qty. 39+1 extra) (Qty. 8+1 extra)
Touch-up Pen Hex Wrench
(Qty. 1) (Qty. 2)
Tools required: Phillips screwdriver (not provided).

5
Parts Identification
Not actual size
J
D
F
D
C
B
A
H
I
E
E
N
N
K
L
M
G
This image may differ depending on model
C
B
A
D
x 2
E
x 2
F
G
N
x 2
K
L
M
H
I
J
HARDWARE

6
E
G
J
H
I
2
NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled, go
back and fully tighten all bolts. This will make the assembly easier.
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Orient and attach the Desk Stretchers (H, I and J) between one Side Frame (E) and the Middle Tier
Right Frame (G) with six 30mm Bolts (2) as shown.
② x 6
Assembly Instructions

7
Assembly Instructions
3. Fasten the metal bracket on Desk Front Stretcher (H) to the Side Frame (E) with two 15mm Bolts (1).
x 2
E
H
1

8
Assembly Instructions
4. Align and attach two Fixed Shelves (D) to the lower rails of Middle Tier Right Frame (G) with four
30mm Bolts (2).
G
D
D
2
② x 4

9
D
D
F
2
Assembly Instructions
5. Orient and attach the Middle Tier Left Frame (F) to the left side of both Fixed Shelves (D) with four
30mm Bolts (2).
② x 4

10
EK
L
M
2
Assembly Instructions
6. Orient and attach the Return Stretchers (K, L and M) to the other Side Frame (E) with three 30mm Bolts
(2) as shown.
② x 3

11
E
K
1
Assembly Instructions
7. Fasten the metal bracket on Return Front Stretcher (K) to the Side Frame (E) with two 15mm Bolts (1).
① x 2

12
IMPORTANT NOTICE
The desk is designed to be revertible. Consider the location you prefer to place the desk relative to
your room, two configurations can be available.
8. Depending on your room you can choose the preferred configuration above which suits your needs.
Attach the assembled Return Stretchers (K, L and M) to the previous assembly with one 15 mm Bolt (1)
and two 30 mm Bolts (2) as shown. DO NOT fully tighten the bolts in this step.
F
K
L
M
1
2
K
L
M
F
H
1
2
2
② x 2
① x 1

13
Assembly Instructions
9. Properly position the Top Panels (A, B and C) onto the previous assembly. Make sure that the mounting
holes overlap the threaded inserts underneath the tops and the grommets are located at back side. Fasten the
Top Panels (A, B and C) into place with twenty 30mm Bolts (2).
K
L
E
E
H
I
C
B
A
2
2
K
L
F
E
H
I
E
C
B
A
2
2
② x 20

14
Assembly Instructions
10. Align and attach two X Crossbars (N) to the back of the assembled unit with eight 8mm Bolts (3).
Tighten the bolts with a Phillips screwdriver.
N
N
M
J
3
N
N
J
M
3
③ x 8

15
Assembly Instructions
11. Now, go back and securely tighten all the bolts. Make sure all the parts are tight and there are no gaps
between the parts. This will keep the unit square.
12. If necessary, adjust the pre-attached floor levelers at the bottom of all Side Frames to level the unit.

16
Care and Maintenance
 Use a soft, clean cloth that will not scratch the surface when dusting.
 Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
 Using solvents of any kind on your furniture may damage the finish.
 Never use water to clean your furniture as it may cause damage to the finish.
 Always use coasters under beverage glasses and flowerpots.
 Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing.
 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
 Check bolts/screws periodically and tighten them if necessary.
Further Advice about Wood Furniture Care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
A touch-up pen has been provided to minimize the small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace
it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your
highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Whalen Furniture Manufacturing
1578 Air Wing Road, San Diego, CA 92154, USA
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com

ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2022-05-17 Rev. 0001-A
E critorio aju table
Modelo # MS62025004001
ENSAMBLE REQUERIDO POR ADULTO
Si tienen alguna pregunta acerca del en amble o i alguna parte e tá faltante, no retorne e té producto
a la tienda donde lo compro. Por favor llame a nue tro departamento de ayuda al cliente teniendo u
in tructivo y li ta de parte para proveer el modelo, nombre de parte o el número de fábrica:
866-942-5362
Hora e tándar del Pacífico: 8:30 a.m. - 4:30 p.m., de Lune a Vierne
O vi ite nue tra página de Internet 24 hora al día, 7 día a la emana para a i tencia
www.whalenstyle.com
O mande un correo electrónico a [e-mail]
NÚMERO de LOTE:
FECHA de COMPRA: / /
E critorio e quina L opcional
E critorio extra largo opcional

2
FABRICANTE: Whalen Furniture Manufacturing
CATALOGO: Escritorio ajustable
MODELO # MS62025004001
NOTA ESPECIAL
Por favor lea todo el instructivo antes de ensamblar. Examinar todo el material de
empaque antes de tirar el cartón. Retirar cualquier grapa del cartón antes de tirar. Retirar
todas las partes del cartón y separar en grupos como es indicado en la lista de partes. Por
favor de asegurar que todas las partes están presentes antes del ensamble. El uso de
herramientas eléctricas para completar el ensamble no es recomendado.
MÁ XI M O P E S O R EC O ME N D A DO
ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS
INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA
INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES.
CARGA MÁXIMA 90.8 kg / 200 lb.
CARGA MÁXIMA 22.7 kg / 50 lb.

3
Lista de partes y material de ferretería
Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de
ferretería antes de iniciar el ensamblado.
A- Panel superior del complemento (Cant. 1) B- Panel superior de la parte media (Cant. 1)
C- Panel superior del escritorio (Cant. 1) D- Repisa fija (Cant. 2)
E- Marco lateral (Cant. 2) F- Marco izquierdo de la parte media (Cant. 1)
G- Marco derecho de la parte media (Cant. 1) H- Soporte frontal del escritorio (Cant. 1)
I- Soporte posterior del escritorio (Cant. 1) J- Soporte inferior del escritorio (Cant. 1)

4
Lista de partes y material de ferretería
Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de
ferretería antes de iniciar el ensamblado.
K- Soporte frontal del complemento (Cant. 1) L- Soporte posterior del complemento (Cant. 1)
M- Soporte inferior del complemento (Cant. 1) N- Soporte X (Cant. 2)
(1) Perno de 1/4 pulgadas x 15mm (2) Perno de 1/4 pulgadas x 30mm (3) Perno de 5/32 pulgadas x 8mm
(Cant. 5+1 extra) (Cant. 39+1 extra) (Cant. 8+1 extra)
Bolígrafo de retoque Llave hexagonal
(Cant. 1) (Cant. 2)
Herramientas requeridas: Desarmador estrella (no provisto).