Mainstays MS95-010-103-02 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-05-03 Rev. 0001-B Factory: LENCHE
Mainstays 5 pc Dining Set
Stock # MS95-010-103-02
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED:
/
/

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Mainstays 5 pc Dining Set (MS95-010-103-02)
MADE IN MALAYSIA
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware part out of reach of children.
4. Please wait until all steps are completed before tightening bolts.
5. Make sure all bolts are tightly fastened before the unit is used.
MAXIMUM LOAD 400 lb. (181.4 kg)
MAXIMUM RECOMMENDED WEIGHT LOADS
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE
MAXIMUM WEIGHTS INDICATED. USE WITH HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.
GENERAL INFORMATION, TIPS & TRICKS
MAXIMUM LOAD 300 lb. (136 kg)

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Table Top (1) B- Table Leg (4)
C- Chair Left Back Leg (4) D- Chair Right Back Leg (4)
E- Chair Backrest (4) F- Chair Front/Back Rail (8)
G- Seat Cushion (4) H- Chair Left Front Leg (4)
I- Chair Right Front Leg (4) J- Chair Upper Side Rail (8)
K- Chair Front Stretcher (4) L- Chair Side Stretcher (8)

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) M8 x 80 mm Bolt (8+1 extra) (2) Large Lock Washer (8+1 extra)
(3) Large Flat Washer (8+1 extra) (4) M6 x 50 mm Bolt (48+2 extra)
(5) M6 x 65mm Bolt (16+1 extra) (6) Small Lock Washer (32+1 extra)
(7) Small Flat Washer (32+1 extra) (8) Barrel Nut (24+1 extra)
(9) M4 x 38 mm Screw (56+2 extra) (10) Ø8 x 30 mm Wood Dowel (72+2 extra)
4 mm Allen Wrench (2) 5 mm Allen Wrench (1)
Tools required: Allen wrench (provided) and Phillips screwdriver (not provided).

5
Assembly Instructions for Table
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Position the Table Top (A) upside down on a level and protective surface, as shown.
3. Remove the additional wood blocks attached at the corners by unscrewing the wood screws. These are
used for shipping purposes only. After removing them, please discard.
A

6
Assembly Instructions for Table
4. Attach four Legs (B) to the apron corners of Table Top (A) by using the 80 mm Bolts (1) with the Large
Lock Washers (2) and Flat Washers (3) through the drilled holes on corner blocks and securely screw
into the threaded inserts on the Legs with 5 mm Allen wrench.
5. Stand the table upright and place it at your desired location.
A
B
B
B
B
123
Large Lock Washer
(8 used in this step)
②
M8 x 80 mm Bolt
(8 used in this step)
①
Large Flat Washer
(8 used in this step)
③

7
Assembly Instructions for Chair
NOTE: Please do not fully tighten all bolts until you finish assembling the frame. Once assembled,
go back and fully tighten all bolts. This will make it easier during assembly of unit.
6. Insert one Barrel Nut (8) into the bottom side hole of one Chair Backrest (E). Be sure that the cross slot
on the Barrel Nut faces out and that the threaded hole points towards the entry of the bolt along the
bottom rail.
7. Align and attach the Chair Backrest (E) to the Chair Right Back Leg (D) with three Wood Dowels (10)
and two 50 mm Bolts (4). As shown.
4
10
D
E
4
8
10
Barrel Nut
(1 used in this step)
⑧
Wood Dowel
(3 used in this step)
⑩
M6 x 50 mm Bolt
(2 used in this step)
④

8
Assembly Instructions for Chair
8. Align and attach one Chair Back Rail (F) to the Chair Right Back Leg (D) by using two Wood Dowels
(10), one 65 mm Bolt (5) and one Barrel Nut (8). As shown.
5
8
10
D
F
E
M6 x 65 mm Bolt
(1 used in this step)
⑤
Wood Dowel
(2 used in this step)
⑩
Barrel Nut
(1 used in this step)
⑧

9
Assembly Instructions for Chair
9. Repeat the same procedure to attach one Chair Left Back Leg (C) at the opposite end.
Barrel Nut
(2 used in this step)
⑧
M6 x 65 mm Bolt
(1 used in this step)
⑤
Wood Dowel
(5 used in this step)
⑩
M6 x 50 mm Bolt
(2 used in this step)
④
C
4
4
5
10
10
F
E
8
10

10
Assembly Instructions for Chair
10. Insert four Wood Dowels (10) into the outer holes of one Chair Front Rail (F) at both ends.
11. Align and attach the Chair Front Rail (F) and one Chair Front Stretcher (K) between the Left and Right
Front Legs (H and I), using two 65 mm Bolts (5) and two Barrel Nuts (8). As shown.
5
8
10
5
810
F
K
I
H
Wood Dowel
(4 used in this step)
⑩
Barrel Nut
(2 used in this step)
⑧
M6 x 65 mm Bolt
(2 used in this step)
⑤