Mainstays MS18-D1-1007-14 User manual

1PB
model# MS18-D1-1007-14
Lot#_________Date________
Customer Service:
1.877.436.7290
[email protected]
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
brown/black
Manufactured By:
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
Assembly Instructions
BENNETT
TOWER BOOKCASE

2
TOP PANEL
BOTTOM PANEL
LEFT SIDE ASSEMBLY
RIGHT SIDE ASSEMBLY
PARTITION
LEFT SHELF [X2]
RIGHT SHELF [X3]
A
B
C
D
E
F
G
BACK PANEL
LEG [X4]
H
I
Before you begin:
1. Check for damaged or missing parts.
2. Use the carton as a working surface to prevent product damage during assembly.
TOOLS NEEDED
Flat Head Screwdriver Phillips Head Screwdriver
PARTS LIST

2 3
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
5. Flat Head Screw
x6
3. Cam
x26
4. Wood Dowel
x16
1. Bolt
x16
2. Cam Bolt
x26
6. Pan Head Screw
x19
7. Allen Wrench
x1

4
10. Washer
x2
HARDWARE LIST
CAUTION:
1. Make sure the screws go through the pre-drilled holes properly.
2. Do not over tighten bolts.
8. Wall Screw
x1
9. Wall Strap
x1
11. Wall Anchor
x1
12. Cam Cover
x6

4 5
1 2
3 4 5
180º
HOW TO USE THE CAM LOCK SYSTEM

6
x20 x20 x10
STEP 1
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Screw-In cam bolts must be screwed down ush.
3. Refer to page 4 for instructions on how to use the cam lock system.
4. Wood
D o w e l
2. Cam Bolt 3. Cam
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

76
x6 x6 x3 x6
1. Carefully tap small wooden dowels into place. Leave 1/2”of the dowels sticking out.
2. Make sure the screws go through the pre-drilled holes properly.
3. Do not over tighten screws.
STEP 2
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
4. Wood
D o w e l
2. Cam Bolt 3. Cam 12. Cam
Cover

8
x3 x6
4. Wood
Dowel
5. Flat Head
Screw
1. Do not over tighten screws.
STEP 3
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

98
x18
STEP 4
1. Do not over tighten screws.
6. Pan Head
Screw
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the case is
square. (if using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) Install
the remaining screws, starting with the corners.

10
x16 x1
1. Do not over tighten bolts.
STEP 5
1. Bolt 7. Allen
Wrench
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

10 11
x1x1x1x1
x2
11
810
6
10
9
STEP 6
6. Pan Head
Screw
8. Long Flat
Head Screw
9. Wall Strap
10. Washer
11. Wall
Anchor
position against wall
mark position of strap hole on wall
drill 1/4”hole
tap in wall anchor
fasten anti-tip strap with wall
screw provided
NOT TO SCALE. REFER TO PAGE 3 FOR ACTUAL SIZE HARDWARE.

12
30 lbs. / 13.6 kg.
15 lbs. /
6.8 kg.
10 lbs. /
4.5 kg.
WARNING: Do not exceed the maximum load capacity. Exceeding the maximum load capacity may result in
collapse and possible injury.
Your complete satisfaction is our number 1 priority. Our product is designed and manufactured to meet the
highest quality of standards. In the event that you have assembly questions, or parts are missing or damaged,
our customer service department would appreciate the opportunity to assist you.
This product carries a one (1) year warranty against defects in workmanship and materials. Defective product
will be replaced free of charge within the stated warranty period, when returned by the original purchaser with
proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. Please
contact our Customer Service at 1-877-436-7290 to obtain information on warranty performance. This warranty
gives you specic legal rights and you may also have other rights which vary from State to State.
Furniture Care Instructions:
Dust with clean, lint-free cloth.
Use furniture spray polish as needed.
Customer Service:
877.436.7290
[email protected]
!WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV’s or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.

1PB
model# MS18-D1-1007-14
Lot#_________Fecha_______
Servicio al Cliente:
1.877.436.7290
[email protected]
ESTE MANUAL DE INSTRUCCIONES CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y GUARDE PARA REFERENCIA FUTURA.
marrón/negro
Fabricado Por :
BDDMI
1321 Tyler St NE, Minneapolis, MN 55413
LIBRERO EN TORRE
BENNETT
Instrucciones de Ensamble

2
PANEL SUPERIOR
PANEL INFERIOR
ENSAMBLE DEL LADO IZQUIERDO
ENSAMBLE DEL LADO DERECHO
DIVISOR
REPISA FIJA IZQUIERDO [X2]
REPISA FIJA DERECHO [X3]
A
B
C
D
E
F
G
PANEL POSTERIOR
PATA [X4]
H
I
Antes de comenzar:
1. Compruebe si hay piezas dañadas o faltantes.
2. Utilice la caja de cartón como supercie de trabajo para evitar daños al producto durante el montaje.
Destornillador de Cabeza Plana Destornillador Phillips
HERRAMIENTAS NECESARIAS
LISTA DE PARTES

2 3
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
5. Tornillo de Cabeza
Plana
x6
3. Leva
x26
4. Clavija de Madera
x16
6. Tornillo de Cabeza
de Noria
x19
7. Llave Allen
x1
2. Tornillo de Leva
x26
1. Perno
x16

4
10. Arandela
x2
LISTA DE ARTÍCULOS DE FERRETERÍA
PRECAUCIÓN:
1. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
2. No sobreapriete los tornillos.
8. Tornillo de Pared
x1
9. Cincha de Pared
x1
11. Taquete de Pared
x1
12. Cubierta del Tornillo
x6

4 5
1 2
3 4 5
180º
COMO USAR EL SISTEMA FIJADOR DE LEVA

6
x20 x20 x10
PASO 1
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Los tornillos de leva deben de estar atornillados al ras.
3. Reérase a la página 4 para instrucciones para como usar el sistema de levas.
4. Clavija de
Madera
2. Tornillo
de Leva
3. Leva
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.

76
x6 x6 x3 x6
PASO 2
1. Con cuidado golpee las clavijas de madera en su lugar. Deje un saliente de 1.27 cm (½”) en las clavijas.
2. Cerciórese que los tornillos pasen por los agujeros pretaladrados de manera apropiada.
3. No sobreapriete los tornillos.
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.
4. Clavija de
Madera
2. Tornillo
de Leva
3. Leva 12. Cubierta
del Tornillo

8
x3 x6
4. Clavija de
Madera
5. Tornillo
de Cabeza
Plana
PASO 3
1. No sobreapriete los tornillos.
NO ESTÁ A ESCALA. CONSULTE LA PÁGINA 3 FOR HARDWARE DE TAMAÑO REAL.