Maiwe MIEN2205 User manual

MIEN2205
Industrial Ethernet Switch
User manual
1
Packing list
2
Product description
The package of this switch contains the following items. If any item is found to be
missing or damaged, please contact the agent or the customer service center of
Maiwe for assistant.
Items
Quantity
Remarks
Industrial Ethernet Switch
1PCS
User Manual
1PCS
This series switches are unmanaged din-rail industrial Ethernet switch.
MIEN2205 supports 100M Ethernet ports (5*100M copper ports);
MIEN2205

3
Interface description
Item
Description
Ground screw
Crimp one end of the grounding screw with the cold-pressed
terminal. The other end of the grounding wire is connected
to the ground, and the grounding wire is not less than
2.5mm2
Power interface
Support Dual DC12-48V
Ethernet RJ45
port
Supports automatic MDI/MDI-X connection. You can connect the
switch to terminal devices, servers, hubs, or other switches.
Din-rail kit
To fix the switch.
The indicator description of the switch is shown in the following table.
Indicator lights
Status
Definition
System Status LED
PWR1/PWR2
On
The power is connected and operating normally
Off
The power is not connected or the system is not operating
normally
RUN
Flashing
The system is operating normally (some models are always
on to indicate normally)
Off
The system is not working properly
Fiber Port Status LED
LINK
On
The port has established a valid network connection
Flashing
There is network activity on the port
Off
No valid network connection is established on the port
RJ45 Port Status LED
Each RJ45 port has two indicator lights, the yellow light is the port plastic rate indicator, the
green light is the port connection status indicator.
10/100M
(Yellow)
On
100M working state (namely 100Base-TX)
Off
10M working status (namely 10Base-T)
Link/Act
(Green)
On
The port has established a valid network connection
Flashing
There is network activity on the port
Off
No valid network connection is established on the port
Ground screw
DIN-RAIL kit

4
Hardware installation
Device installation
Device connection
Installation and safety Precautions
To prevent equipment damage or personal injury caused by improper use, observe
the following precautions:
During the installation process, you need to wear anti-static gloves or anti-static
gloves, and power-off the switch.
Please make sure that the input voltage is within the input voltage range marked
on the switch.
The transmission distance has a certain relationship with the connected wire. It
is recommended to use a standard Cat5e/6 network cable.
The equipment must be grounded for lightning protection, otherwise the
protection level of the equipment will be greatly reduced; please use a wire of No.
20 or more to connect the grounding terminal to the ground.
The power line, ground line and signal line are laid out separately and the
distance is not less than 5cm.
Please pay attention to the symbol below for marking label.
Tilt the switch upwards so that the upper end of the buckle is fastened to the
upper end of the DIN rail.
Network cables connection
Connect the optical fiber and network cable to the port in the correct
Catagory5 direct connection Catagory5 crossover connection
Optical fiber connection
Connect the optical fiber to the corresponding optical fiber interface. The optical
fiber interface is used in pairs (TX and RX as a pair), TX is optical receiver, RX is
optical sender.

1. When using a switch, the voltage can only be input from V1+ and V1-, V1+
connects to live wire L, and V1- to neutral wire N. Do not connect from V2+, V2-;
pay attention to safety and prevent electric shock.
2. Power-on operation: First connect the power cord to the power terminal of the
device according to the definition shown in the figure above, and then power on.
3. Power-off operation: first unplug the power plug, and then remove the power cord.
5
Specifications
Warning
Power input
Before connecting the power cord, make sure that the ground is connected. Do
connect the power cord to the power terminal of the device according to the
definition.
Notes
MIEN2205
Switch properties
Bandwidth
1G
Cache size
748Kbit
MAC table size
2K
Port
100M
Copper port
5*10/100Base-T(X) RJ45 ports
Full-duplex/half-duplex adaptive, supports MDI/MDI-X adaptive
Power
Consumption
1.5W@24V(MAX)
Working current
0.5A
DC powerinput
DC12-48V d.c.
Supports dual power supply redundancy and reverse connection protection
Mechanical
Size
118mm×35mm×86mm（L×W×H）(not include din-rail)
Installation
35mm standard din-rail
Heat
Aluminum alloy single-rib chassis surface scattered
Weight
about 0.64kg
Working Environment
Working Temp.
-40℃~85℃
Storage Temp.
-40℃~70℃
Humidity
5%~95%(No condensation)
Safety
Safety
UL/CSA/IEC/EN 62368-1, 2nd
EMC
Hot Parts
Burned fingers when handling the parts
Wait one-half hour after switching off before handling the
parts

6
Order guide
7
Pledge
EMC
IEC61000-4-2(ESD),Level 4
IEC61000-4-5(Surge),Level 4※Ethernet ports support 6KV lightning
protection
IEC61000-4- 4(EFT),Level 4
IEC61000-4-3(RS),Level 4
IEC61000-4-6(CS),Level 4
Item
10/100Base-T(X)
100Base-FX
Power
MIEN2205
5
0
DC: DC12-48V d.c
Thank you for purchasing Maiwe products. You will enjoy the following services when
using Maiwe products.
We solemnly promises: under normal use, one month's return, one-year free
maintenance, five-year warranty, and lifetime maintenance. The specific details are
as follows:
If Maiwe products have quality problems and cannot work normally, they will be
refunded for one month, free maintenance for one year, warranty for five years,
and maintenance for life.
If the number of repaired products is less than 10, the repair service will be
completed within 7 days (excluding transportation time), and the repair service
will be completed within one month for more than 10 sets.
Optical passive products such as optical fibers, optical cables, jumpers, flanges,
and optical cable terminal boxes are guaranteed within two years, but no return
service is provided.
The accessories and power supply that come with the product are guaranteed
for one year.
When sending the product back to Maiwe for repair, it is recommended that the
customer use the original packaging or the packaging with the same protective
effect, otherwise the customer shall bear the risks that occur during the
transportation.
The repaired product can enjoy another 6 months warranty service.
The product after-sales service is detailed in the purchase and sale contract,
and Maiwe has the final interpretation right of this description.

Wuhan Maiwe Communication Co., Ltd.
Add: Building E2, No. 2 Building, Area E, No. 52 Liufang Avenue, East lake
High-tech Development Zone, Wuhan, China.
Tel: [phone] Fax: [phone]
Post Code: 430205
Site: www.maiwe.com
Statement
Due to the continuous updating and improvement of products and technologies, the
contents of this manual will be updated from time to time. All the information in the
manual is only used for instructions, if the content in the text does not completely
match the actual product, please understand and please contact our customer
service in time.
Copyright 2021 Maiwe Communication All rights reserved.
The right to interpret the information published in this material belongs to
Wuhan Maiwe Communication Co., Ltd.