Maiwe MIEN2208-F User manual

Industrial Ethernet Switch
User manual
The package of this switch contains the following items. If any item is found to be
missing or damaged, please contact the agent or the customer service center of
Maiwe for assistant.
Items
Quantity
Remarks
Industrial Ethernet Switch
1PCS
Power cord
1PCS
AD220 model only
User Manual
1PCS
The switch is a unmanaged din-rail industrial Ethernet switch. MIEN2208 series
provides 8 100M Ethernet interfaces. Among them, MIEN2208-F (1 100M fiber and 7
100M copper ports), MIEN2208-2F (2 100M fiber and 6 100M copper ports), MIEN
2208-4F (4 100M fiber and 4 100M copper ports).
MIEN2208-F
MIEN2208-2F
MIEN2208-4F
Packing list
Product description
MIEN2208-F MIEN2208-2F MIEN2208-4F

Take MIEN2208-2F as an example.
Item
Description
Ground screw
Crimp one end of the grounding screw with the cold-pressed
terminal. The other end of the grounding wire is connected tothe
ground, and the grounding wire is not less than 2.5mm2
Power interface
Support Dual DC12-48V or DC48V(36-72V).
Support single power input AC85-264V or DC110-370V.
Relay output
interface
Relay alarm output function; this relay is a normally open and one
normally closed relay, the middle one is the common terminal, the two
left terminals are normally open relays, and the two right two terminals
are normally closed relays. When the switch works normally, the
normally open relay is energized and closed, and the normally closed
relay is disconnected. When the system is powered down, the normally
open relay is powered off and the normally closed relay is closed. The
recommended switching load capacity of the relay is 1A (24VCD).
Ethernet RJ45 port
Supports automatic MDI/MDI-X connection. You can connect the switch
to terminal devices, servers, hubs, or other switches.
Fiber port
The 100M fiber port is a 100Base-FX full-duplex single-mode or
multi-mode fiber connector, which support single-fiber or dual- fiber
connectors, and the connector can be SC, ST or FC. The optical
fiber connectors must be used in pairs (TX and RX are a pair).
Din-rail kit
To fix the switch.
The indicator description of the switch is shown in the following table.
Indicator lights
Status
Definition
System Status LED
PWR1/PWR2
On
The power is connected and operating normally
Off
The power is not connected or the system is not operating
normally
RUN
Flashing
The system is operating normally (some models are always
on to indicate normally)
Off
The system is not working properly
Fiber Port Status LED
LINK
On
The port has established a valid network connection
Flashing
There is network activity on the port
Off
No valid network connection is established on the port
RJ45 Port Status LED
Each RJ45 port has two indicator lights, the yellow light is the port plastic rate indicator, the
green light is the port connection status indicator.
10/100M
(Yellow)
On
100M working state (namely 100Base-TX)
Off
10M working status (namely 10Base-T)
Link/Act
(Green)
On
The port has established a valid network connection
Flashing
There is network activity on the port
Off
No valid network connection is established on the port
Indicator lights
Status
Definition
System Status LED
PWR1/PWR2
O n
The power is connected and operating normally
O ff
The power is not connected or the system is not operating
normally
RUN
F lashing
The system is operating normally (some models are always
on to indicate normal)
Off
The system is not working properly
Fiber Port Status LED
LINK
On
The port has established a valid network connection
Flashing
There is network activity on the port
Off
No valid network connection is established on the port
RJ45 Port Status LED
Each RJ45 port has two indicator lights, the yellow light is the port plastic rate indicator, the green light is the
port connection status indicator.
10 / 100M
(Y ellow)
On
100M working state (namely 100Base-TX)
O ff
10M working status (namely 10Base-T)
Link / Act
(Green)
O n
The port has established a valid network connection
F lashing
There is network activity on the port
Off
No valid network connection is established on the port
Interface description
Ground screw
Power
Relay output
110mm
140
Fiber port
54mm
RJ45 port
Indicate lights
110mm
DIN-Rail
138mm

Installation Precautions
To prevent equipment damage or personal injury caused by improper use, observe
the following precautions:
During the installation process, you need to wear anti-static gloves or anti-static
gloves, and power-off the switch.
Please make sure that the input voltage is within the input voltage range marked
on the switch.
The transmission distance has a certain relationship with the connected wire. It
is recommended to use a standard Cat5e/6 network cable.
The equipment must be grounded for lightning protection, otherwise the
protection level of the equipment will be greatly reduced; please use a wire of No.
20 or more to connect the grounding terminal to the ground.
The power line, ground line and signal line are laid out separately and the
distance is not less than 5cm.
Tilt the switch upwards so that the upper end of the buckle is fastened to the
upper end of the DIN rail.
The lower end of the back buckle is buckled into the DIN rail.
Network cables connection
Connect the optical fiber and network cable to the port in the correct
Catagory5 direct connection Catagory5 crossover connection
Optical fiber connection
Connect the optical fiber to the corresponding optical fiber interface. The optical
fiber interface is used in pairs (TX and RX as a pair), TX is optical receiver, RX is
optical sender.
Hardware installation
Device installation
Device connection

1. Signals were transmitted by laser through optical fiber. The laser meets the
requirement of class I, no harm with normal operation. Do not look directly into the
fiberport and the end of the optical fiber terminator.
2. Dust plugs need to be installed when optical connectors and optical modules are
notin use. Dust caps need to be installed when optical fibers are not in use.
3. The bending radius of optical fiber should be greater than 20 times the diameter of
the optical fiber. In general, the bending radius should be equal to or greater than
40mm.
1. When using a switch, the voltage can only be input from V1+ and V1-, V1+ connects
to live wire L, and V1- to neutral wire N. Do not connect from V2+, V2-; pay attention
to safety and prevent electric shock.
2. Power-on operation: First connect the power cord to the power terminal of the
device according to the definition shown in the figure above, and then power on.
3. Power-off operation: first unplug the power plug, and then remove the power cord.
Warning
Power input
Before connecting the power cord, make sure that the ground is connected. Do
connect the power cord to the power terminal of the device according to the definition.
Notes
MIEN2208-F
MIEN2208-2F
MIEN2208-4F
Switch performance
Backplane bandwidth
1.6G
Cache size
768Kbit
MAC address
2K
Interface
100Base-FX port
1*100Base-FX
2*100Base-FX
4*100Base-FX
Connector SC/FC/ST optional
100Base-TX port
7*10 /100Base-TX
RJ45 ports
6*10 /100Base-TX
RJ45 ports
4*10/100Base-TX
RJ45 ports
With adaptive function, support MDI/MDI-X connection
Power
Power consumption
<5W@24V full load
DC input
Support dual DC12~48V or DC48V (36-72V) power supply
AC input
AC85~264V (frequency: 47~63Hz) or DC110~370V
Mechanical
Size
138mm×54mm×110mm(H×W×D)(Excluding DIN rail)
Installation method
35mm standard DIN rail installation
Heat dissipation form
Aluminum alloy single-rib chassis surface heat dissipation, no
fan.
Weight
About 0.67kg
IP protection
IP40
Working environment
Operating temp.
-40～+85℃
Storage temp.
-40～+85℃
Humidity
5～95% (No condensation)
Industry standard
EMC
IEC61000-4-2(ESD), Level4
IEC61000-4-5(Surge), Level4
IEC61000-4-4(EFT), Level4
Specifications

IEC61000-4-3(RS), Level4
IEC61000-4-6(CS), Level4
※The network port supports 6KV lightning protection
Model
100Base-FX
100Base-TX
Power
MIEN2208-F
1
7
DC power supply:
DC12~48V or DC48V (36~72V) optional
AC power supply:
AC85~264V(Freq.:47~63Hz) or DC110 〜
370V
MIEN2208-2F
2
6
MIEN2208-4F
4
4
Thank you for purchasing Maiwe products. You will enjoy the following services when
using Maiwe products.
We solemnly promises: under normal use, one month's return, one-year free
maintenance, five-year warranty, and lifetime maintenance. The specific details are
as follows:
If Maiwe products have quality problems and cannot work normally, they will be
refunded for one month, free maintenance for one year, warranty for five years,
and maintenance for life.
If the number of repaired products is less than 10, the repair service will be
completed within 7 days (excluding transportation time), and the repair service
will be completed within one month for more than 10 sets.
Optical passive products such as optical fibers, optical cables, jumpers, flanges,
and optical cable terminal boxes are guaranteed within two years, but no return
service is provided.
The accessories and power supply that come with the product are guaranteed
for one year.
When sending the product back to Maiwe for repair, it is recommended that the
customer use the original packaging or the packaging with the same protective
effect, otherwise the customer shall bear the risks that occur during the
transportation.
The repaired product can enjoy another 6 months warranty service.
The product after-sales service is detailed in the purchase and sale contract, and
Maiwe has the final interpretation right of this description.
Wuhan Maiwe Communication Co., Ltd.
Add: Building E2, No. 2 Building, Area E, No. 52 Liufang Avenue, East lake
High-tech Development Zone, Wuhan, China.
Tel: [phone] Fax: [phone]
Post Code: 430205
Site: www.maiwe.com
Statement
Due to the continuous updating and improvement of products and technologies, the contents
of this manual will be updated from time to time. All the information in the manual is only used
for instructions, if the content in the text does not completely match the actual product, please
understand and please contact our customer service in time.
Copyright 2021 Maiwe Communication All rights reserved.
The right to interpret the information published in this material belongs to Wuhan Maiwe
Communication Co., Ltd.
Order guide
Pledge