Makita RW01 User manual
2ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: RW01
Applicable battery cartridge and charger
WARNING:Only use the battery cartridges and chargers listed above.
SAFETY WARNINGS
General power tool safety warnings
WARNING:Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool.
Save all warnings and instruc-
tions for future reference.
Work area safety
Keep work area clean and well lit.
Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust.
Keep children and bystanders away while
operating a power tool.
Electrical Safety
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools.
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
Do not expose power tools to rain or wet con-
ditions.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply.
Power tools can produce electromagnetic elds
(EMF) that are not harmful to the user.
3ENGLISH
Personal Safety
Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication.
Use personal protective equipment. Always
wear eye protection.
Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool.
Remove any adjusting key or wrench before
turning the power tool on.
Do not overreach. Keep proper footing and
balance at all times.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles.
Always wear protective goggles to protect
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA.
It is an employer's responsibility to enforce the
use of appropriate safety protective equipment
by the tool operators and by other persons in
the immediate working area.
Power tool use and care
Do not force the power tool. Use the correct
power tool for your application.
Do not use the power tool if the switch does
not turn it on and off.
Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any adjust-
ments, changing accessories, or storing power
tools.
Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool.
Maintain power tools and accessories. Check for
misalignment or binding of moving parts, break-
age of parts and any other condition that may
affect the power tool’s operation. If damaged, have
the power tool repaired before use.
Keep cutting tools sharp and clean.
Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed.
Keep handles and grasping surfaces dry, clean
and free from oil and grease.
When using the tool, do not wear cloth work
gloves which may be entangled.
Battery tool use and care
Recharge only with the charger specied by
the manufacturer.
Use power tools only with specically desig-
nated battery packs.
When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.
Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help.
Do not use a battery pack or tool that is dam-
aged or modied.
Do not expose a battery pack or tool to re or
excessive temperature.
Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specied in the instruc-
tions.
Service
Have your power tool serviced by a qualied
repair person using only identical replacement
parts.
Never service damaged battery packs.
4ENGLISH
Follow instruction for lubricating and chang-
ing accessories.
Do not modify or attempt to repair the appli-
ance or the battery pack except as indicated in
the instructions for use and care.
Symbols
Cordless Ratchet Wrench safety
warnings
Hold the power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden wiring.
Hold the tool rmly.
Always be sure you have a rm footing.
Be sure no one is below when using the tool in
high locations.
Wear ear protectors.
Check the impact socket carefully for wear,
cracks or damage before installation.
Keep hands away from rotating parts.
Do not touch the ratchet head, impact socket,
bolt, nut or the workpiece immediately after
long time operation.
SAVE THESE INSTRUCTIONS.
WARNING:DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Important safety instructions for
battery cartridge
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using battery.
Do not disassemble battery cartridge.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
Do not short the battery cartridge:
Do not touch the terminals with any con-
ductive material.
Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
Do not expose battery cartridge to water
or rain.
A battery short can cause a large current ow,
overheating, possible burns and even a breakdown.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
Be careful not to drop or strike battery.
Do not use a damaged battery.
The contained lithium-ion batteries are subject to
the Dangerous Goods Legislation requirements.
When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
Use the batteries only with the products
specied by Makita.
If the tool is not used for a long period of time,
the battery must be removed from the tool.
SAVE THESE INSTRUCTIONS.
CAUTION:Only use genuine Makita batteries.
Tips for maintaining maximum
battery life
Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
Charge the battery cartridge with room tempera-
ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot
battery cartridge cool down before charging it.
5ENGLISH
FUNCTIONAL
DESCRIPTION
CAUTION:Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge.
CAUTION:Be careful not to pinch your n-
gers between the tool and battery.
1.2.3.
CAUTION:Always install the battery cartridge
fully until the red indicator cannot be seen.
CAUTION:Do not install the battery cartridge
forcibly.
Battery protection system
Overloaded:
Low battery voltage:
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
1.2.
Indicator lamps Remaining
capacity
Lighted Off
NOTE:
6ENGLISH
Switch action
CAUTION:Before installing the battery car-
tridge into the tool, always check to see that the
switch lever actuates properly and returns to the
"OFF" position when released.
1.
1.2.3.
CAUTION:When not operating the tool,
always slide the lock lever to the lock position .
Electric brake
Lighting up the front lamp
CAUTION:Do not look in the light or see the
source of light directly.
1.2.
NOTICE:When the tool is overheated, the lamp
ickers. Cool down the tool fully before operating
the tool again.
NOTICE:
Reversing lever action
CAUTION:Always check the direction of
rotation before operation.
CAUTION:Use the reversing lever only after
the tool comes to a complete stop.
1.
7ENGLISH
ASSEMBLY
CAUTION:Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing socket
adaptor
1.2.
1.2.
NOTICE:
Installing or removing socket
CAUTION:Before operation, make sure that
the socket is properly locked onto the socket
adaptor.
NOTICE:
1.2.
OPERATION
CAUTION:Hold the tool rmly especially
when the bolt/nut reaches the seating position.
NOTICE:Hold the tool pointed straight at the
bolt/nut.
8ENGLISH
Using as hand tool
NOTICE:
MAINTENANCE
CAUTION:Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
OPTIONAL
ACCESSORIES
CAUTION:These accessories or attachments
are recommended for use with your Makita tool
specied in this manual.
NOTE:
Other manuals for RW01
1
This manual suits for next models
2
Table of contents
Other Makita Power Tools manuals
Makita
Makita HM1317C User manual
Makita
Makita AN901 User manual
Makita
Makita DTW450 User manual
Makita
Makita DHK180 User manual
Makita
Makita DHR202Z User manual
Makita
Makita BTS130 User manual
Makita
Makita AT638 User manual
Makita
Makita DST221RMJ User manual
Makita
Makita JN1601 User manual
Makita
Makita TB131 User manual
Makita
Makita DCG180RYE User manual
Makita
Makita AN454 User manual
Makita
Makita XTW01 User manual
Makita
Makita DJV142 User manual
Makita
Makita 4604D User manual
Makita
Makita 3706 User manual
Makita
Makita DHR241Z User manual
Makita
Makita M432 User manual
Makita
Makita HM1201 User manual
Makita
Makita TW160DSAJ User manual
Popular Power Tools manuals by other brands
Hyundai
Hyundai HCOMBI25 Original instructions
Slime
Slime GARAGE INFLATION STATION manual
Aperia Technologies
Aperia Technologies Halo Connect user manual
Dynabrade
Dynabrade 52050 operating instructions
Lafayette
Lafayette INDUSTRIAL 120 user manual
MSW Motor Technics
MSW Motor Technics MSW-UNV-21 user manual
