Marmitek BOOMBOOM 55 User manual

BoomBoom 55
3
15
27
41
55
69
User manual
Gebrauchsanleitung
Guide utilisateur
Modo de empleo
Manuale d’istruzioni
Gebruiksaanwijzing
1_20648_20190514_front_UG_BoomBoom 55.pdf 1 14-5-2019 13:50:51

© MARMITEK
2

BoomBoom 55
3
ENGLISH
1 Table of contents
1 Table of contents................................................................3
2 Safety instructions..............................................................4
3 Introduction ........................................................................5
4 Set contents .......................................................................6
5 LED status .........................................................................7
6 Getting started ...................................................................7
6.1 Connecting to your tv or sound system......................8
6.2 Pairing.......................................................................8
6.3 Reconnecting ............................................................9
6.4 Pairing with another device........................................9
6.5 On / off switch............................................................9
6.6 Pairing a second Bluetooth device.............................9
6.7 Deleting paired devices from memory........................9
8 Product details .................................................................10
8.1 Technical specifications...........................................10
9 Frequently asked questions (FAQs) .................................11
11 Notification .......................................................................13
11.1 Declaration of Conformity ........................................13
11.2 Recycling.................................................................14
11.3 Copyrights ...............................................................14

© MARMITEK
4
2 Safety instructions
Please read these instructions thoroughly before you use the
device and keep them for future reference.
Only for indoor use.
Do not use the product in a damp environment or near water.
Do not expose the product to extremely high or low
temperatures, strong light sources or direct sunlight.
This product is not a toy. Keep out of reach of children.
Avoid using headphones/speakers with the volume turned up
for an extended period of time. Doing so may damage your
hearing. It is advisable to keep the volume at a moderate
level at all times.
Never open the product: the device may contain parts with
deadly voltage.
Repairs or service should only be performed by qualified
personnel.
Improper use, self-installed modifications or repairs will void
any and all warranties.
Marmitek does not accept any product responsibility for
incorrect use of the product or use other than for which the
product is intended.
Marmitek does not accept liability for any consequential
damage other than the legal product responsibility.

BoomBoom 55
5
ENGLISH
3 Introduction
Congratulations on your purchase of the Marmitek BoomBoom 55.
This Bluetooth audio transmitter allows you to playback audio from
any sound source through headphones or audio receivers that are
equipped with Bluetooth technology. You can then control the
audio using your sound source (eg. TV) or audio receiver
(Bluetooth headset).
The BoomBoom 55 has a range of approx. 10 metres, enabling
limitless enjoyment of your music in the same or adjoining room.
HD Bluetooth audio transmitter
Listen to music or TV audio with your Bluetooth headphones
Get more from your Bluetooth headphones.
Enjoy your favourite TV shows or music, without bothering
anybody.
Features digital audio inputs and aptX® technology for a
superior music experience.
The best solution for listening to your TV: no noticeable lag
between image and sound, thanks to the latest aptX Low
Latency® technology. *)
Unique ability to use 2 headphones simultaneously.
*) For best results, the headphones should also feature "aptX Low
Latency®" technology. aptx Low Latency only works in single-
mode.

© MARMITEK
6
4 Set contents
A. 1 x BoomBoom 55, universal Bluetooth wireless stereo audio
transmitter
B. 1 x Mini Jack audio cable
C. 1 x Mini Jack to RCA audio cable
D. 1 x USB power cable
E. 1 x USB adapter
F. 1 x set of instructions
Mini-jack kabel
This cable is plugged into the BoomBoom 55's audio input.
Mini-jack adapter cable
This cable enables you to connect the BoomBoom 55 to the audio
output (right-left) of your TV or audio system.
Connection for
audio cable
Pairing button
Connection for
micro USB power
cable
On/Off switch
TOSLINK
connection
A
Led status
Coax connection
B
C

BoomBoom 55
7
ENGLISH
Micro USB power cable
This cable enables you to power the BoomBoom 55.
USB adapter
Connect D to E and provide power to
the BoomBoom 55.
5 LED status
LED status
Omschrijving
Blue LED flashing quick
Pairing mode
Blue LED flashing slowly
Searching for last device
Blue LED on continuously
Connected
Green LED on continuously
aptX Low Latency connection
6 Getting started
Please take the following steps before using the product:
Connect the BoomBoom 55 to your TV or audio system
Power the BoomBoom 55
Pair the BoomBoom 55 with a Bluetooth-enabled headset or
speaker
Enjoy!
We will now explain this step by step.
E
D

© MARMITEK
8
6.1 Connecting to your tv or sound system
For best results, connect the BoomBoom 55 to the digital audio
output (toslink or coaxial) of your TV or audio system:
- Connect your digital audio cable (not included) to the digital
audio output of your TV or audio system
- Connect the other end of the audio cable to the correct
BoomBoom 55 audio input
- Connect the supplied USB power cable to the BoomBoom
55's POWER jack and to the USB power adapter and plug it
into the wall outlet
If your TV or audio system does not have a digital audio output,
you can also connect the BoomBoom 55 to the analogue audio
output or headphones-out:
- Connect one of the two supplied audio cables to the audio
output of your TV or audio system
- Connect the other end of the audio cable to the BoomBoom
55 audio input
- Connect the supplied USB power cable to the BoomBoom
55's POWER jack and to the USB power adapter and plug it
into the wall outlet
6.2 Pairing
1. Make sure your Bluetooth headphones are close to the
BoomBoom 55. The best distance is about 1 metre.
2. Put your Bluetooth headphones in pairing mode (please refer
to your headphones' user manual).
3. Set the BoomBoom 55's switch to ON and press the pairing
button. The LED will now flash quickly.
4. The BoomBoom 55 will now be automatically paired with
your headphones. Once the pairing has been established,
the blue LED on the BoomBoom 55 will light up continuously
(this may take a while).

BoomBoom 55
9
ENGLISH
6.3 Reconnecting
If the BoomBoom 55 or your headphones have been turned off,
the BoomBoom 55 will automatically make a connection once the
BoomBoom 55 and the headphones are turned on again.
6.4 Pairing with another device
You can easily pair the BoomBoom 55 with another pair of
Bluetooth headphones. Switch off the already paired headset and
perform the above pairing procedure again.
6.5 On / off switch
Using the ON/OFF switch, you can turn the BoomBoom 55 on or
off.
6.6 Pairing a second Bluetooth device
With the BoomBoom 55, you can pair two Bluetooth receivers at
the same time.
After pairing the first Bluetooth device, put the second device in
pairing mode.
Now, press the BoomBoom 55's pairing button once.
The pairing with the first Bluetooth device will be momentarily
interrupted, after which both Bluetooth devices will be paired with
the BoomBoom 55. This can take up to two minutes.
6.7 Deleting paired devices from memory
To delete previously paired devices from the memory, proceed as
follows:
Turn off Boom Boom 55.
Press the pairing button and hold.
Turn on the Boom Boom 55.
Wait until the LED blinks rapidly.
Now release the pairing button.
All previously paired devices are now erased.
Continue with 6.2 to pair your Bluetooth device.

© MARMITEK
10
8 Product details
8.1 Technical specifications
General specifications
DC Power 5V Micro USB
Bluetooth
Connection up to two Bluetooth devices (BT 3.0 or
higher)
Supported Bluetooth profiles A2DP
Supported Codec SBC, AAC, aptX, aptX Low Latency
(single-mode only)
Audio Latency SBC, 170 ms - 270 ms
aptX, 60 ms -80 ms
aptX Low Latency, 32 ms - 40 ms
Electric Performance –RF
Bluetooth version Bluetooth 3.0 + EDR, class 2
Transmit Power (Class 2) 4 dBm (Max)
Range Up to 10 meters with Class 2> <2
connection
Up to 30 meters with Class 2> <1
connection
Input
Interface Audio Input Jack 3.5 mm stereo
Coax Digital stereo
Toslink Digital stereo
Electrical Performance—audio RL (1kHz tone / A-weight / 2 Vrms)
Audio Input Level (Max) 300 mV (RMS )
Frequency response 20 ~ 20 kHz (± 3 dB)
Channel Separation Audio R/L ≧85 dB
SNR (nominal, Audio RL) ≧70 dB
total harmonic distortion (nominal, Audio RL) 0.05%
DAC DSP Co-Processor 16-bit Internal
Stereo CODEC with -95dB SNR.
Sample rate Up to 44,1 kHz
Physical
Light Indicator 2 color LED (Blue/Green)
Dimension 56 x 59 x 15 mm
Weight 35 g
Operation temperature -10°C ~ +55°C
Storage temperature -20°C ~ +60°C

BoomBoom 55
11
ENGLISH
Power adapter
Input voltage: 100-240 VAC
Input AC frequency: 50/60 Hz
Output voltage: 5.0 VDC
Output current: 1.0 A
Output power: 5.0 W
Average active efficiency: 75.4 %
Efficiency at low load (10 %): 72.3
No-load power consumption: 0.078 W
5 V power connector: USB A
In order to continue improving the product, Marmitek reserves the right to change
specifications and/or designs without prior notice.
9 Frequently asked questions (FAQs)
I am unable to pair my BoomBoom 55.
Please check the following:
1. Please ensure that the BoomBoom 55 is powered and press
the pairing button twice.
2. Ensure that your headphones are in pairing mode (refer to
your headphones' user manual).
3. Ensure that the distance between your headphones and the
BoomBoom 55 is not too large and there are no major
obstacles between them.
4. To ensure the widest possible range, make sure your
BoomBoom 55 is within line of sight and the internal antenna
is not positioned near large metal objects.
My BoomBoom 55 is paired, but I don't hear anything.
1. Ensure that the blue LED on the Boom Boom 60 lights up
continuously.
2. Ensure that the audio cable is properly connected.
3. Ensure that the BoomBoom 55 is connected to the correct
audio output.
4. Ensure that the volume of your audio source is set to a
comfortable listening level.
5. Ensure that the BoomBoom 55 is paired with the correct
headphones.

© MARMITEK
12
6. Put the BoomBoom 55 and your Bluetooth receiver in pairing
mode again.
I am unable to automatically connect to my headphones.
If you no longer automatically establish a connection with your
headphones, press the pairing button twice (the BoomBoom 55
then goes into pairing mode) and put the headset in pairing mode.
I can't pair a second Bluetooth device.
In order to use this feature, both Bluetooth devices should have
Bluetooth version 3.0 or later.
Can I only use the BoomBoom 55 with headphones?
No, you can use the BoomBoom 55 with any Bluetooth device
with audio playback capability. Including, for example, a Bluetooth
speaker or a Marmitek BoomBoom 93 Bluetooth music receiver. If
attached to your audio system, you can choose whether you want
to hear the sound using the audio system and/or your
headphones, or through the TV's speakers.
Whenever I watch TV, audio is out of sync with video.
The wireless transmission of audio over Bluetooth may indeed
result in some delay (latency).
In most cases, this latency is not disturbing.
If you use a media box to watch TV, connect the BoomBoom 55 to
the audio output of your media box. This results in reduced
latency.
The BoomBoom 55 also supports aptX Low Latency technology.
Your Bluetooth headphones also need to have this technology to
be able to use this. With an aptX Low Latency connection, the
LED turns green.
The sound is distorted by a hum or interference
If you do not use an adapter to power the BoomBoom 55, but, for
example, connect it to your audio system's USB connector, the
resulting ground loop may sometimes cause a hum. In this case,
use the USB power adapter. Using a USB port on, for example, a
PC may also cause interference.
Can I pair a Bluetooth device with aptX Low Latency and a
second device without aptX Low Latency?

BoomBoom 55
13
ENGLISH
Yes, you can. If two devices are paired, aptX Low Latency cannot
be used.
Do you have any other questions that have not been resolved by the above
information? Please go to www.marmitek.com
10 Notification
10.1 Declaration of Conformity
Hereby, Marmitek BV, declares that this BoomBoom
55 is in compliance with the essential requirements
and other relevant provisions of the following
Directives:
Directive 2014/53/EU of the European Parliament and of the
Council of 16 April 2014 on the harmonisation of the laws of the
Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
Directive (EU) 2017/2102 of the European Parliament and of the
Council of 15 November 2017 amending Directive 2011/65/EU on
the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
Commission Regulation (EU) 2019/1782 of 1 October 2019 laying
down eco-design requirements for external power supplies
pursuant to Directive 2009/125/EC of the European Parliament
and of the Council and repealing Commission Regulation (EC) No
278/2009.
You can read the Declaration of Conformity at
http://www.marmitek.com

© MARMITEK
14
10.2 Recycling
Environmental Information for Customers in the
European Union and other European countries with
separate collection systems.
This symbol on the product or on its packaging indicates that this
product shall not be treated as household waste. Instead it shall
be handed over to the applicable collection point for the recycling
of electrical and electronic equipment. It is your responsibility to
dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or
local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and human
health. For more detailed information about the disposal of your
old equipment, please contact your local authorities, waste
disposal service, or the shop where you purchased the product.
10.3 Copyrights
Marmitek is a trademark of Germatron B.V.
BoomBoom 55™ is a trademark of Marmitek B.V. All rights
reserved. Every effort has been made to ensure that the
information in this manual is accurate. Marmitek is not responsible
for printing or clerical errors.
Copyright and all other proprietary rights in the content (including
but not limited to model numbers, software, audio, video, text and
photographs) rests with Marmitek B.V. Any use of the Content, but
without limitation, distribution, reproduction, modification, display
or transmission without the prior written consent of Marmitek is
strictly prohibited. All copyright and other proprietary notices shall
be retained on all reproductions.
Other company and product names mentioned herein may be
trademarks of their respective companies. Mention of third-party
products is for informational purposes only and constitutes neither
an endorsement nor a recommendation. Marmitek assumes no
responsibility with regard to the performance or use of these
products.
MARMITEK BV - P.O. BOX 4257 - 5604 EG EINDHOVEN
THE NETHERLANDS

BoomBoom 55
15
DEUTSCH
1 Inhaltsverzeichnis
1 Inhaltsverzeichnis.............................................................15
2 Sicherheitshinweise .........................................................16
3 Ihr Produkt .......................................................................17
3.1 Einführung...............................................................17
3.2 Verpackungsinhalt...................................................17
4 Produktübersicht ..............................................................18
5 Led status ........................................................................19
6 Los geht’s ........................................................................19
6.1 Anschluss an fernseher oder stereoanlage..............20
6.2 Koppeln...................................................................20
6.3 Erneut verbinden .....................................................21
6.4 Pairing mit einem anderen gerät..............................21
6.5 On / off-schalter.......................................................21
6.6 Ein zweites bluetooth gerät pairen...........................21
6.7 Löschen von gekoppelten Geräten ..........................21
7 Produktinformationen .......................................................22
7.1 Technische Daten....................................................22
8 Häufig gestellte Fragen (FAQs)........................................23
9 Hinweis ............................................................................25
9.1 Konformitätserklärung .............................................25
9.2 Recycling.................................................................26
9.3 Urheberrechte .........................................................26

© MARMITEK
16
2 Sicherheitshinweise
Lesen Sie diese Gebrauchsanleitung sorgfältig durch, bevor
Sie das Gerät in Betrieb nehmen und bewahren Sie diese
Anleitung bitte für eventuelle, spätere Bedarfsfälle auf.
Ausschließlich für Verwendung in Innenräumen.
Dieses Produkt nicht in einer feuchten Umgebung oder nahe
Wasserquellen verwenden.
Setzen Sie dieses Produkt nicht extrem hohen oder
niedrigen Temperaturen, starken Lichtquellen und direkter
Sonneneinstrahlung aus.
Dieses Produkt ist kein Spielzeug. Außer Reichweite von
Kindern halten.
Um Gehörschäden zu vermeiden, sollten Sie nicht über
längere Zeit mit großer Lautstärke hören!
Das Produkt niemals öffnen: Das Gerät kann Teile enthalten,
worauf lebensgefährliche Stromspannung steht.
Überlassen Sie Reparaturen oder Wartung nur Fachleuten.
Bei einer zweckwidrigen Verwendung, selbst angebrachten
Veränderungen oder selbst ausgeführten Reparaturen
verfallen alle Garantiebestimmungen.
Marmitek übernimmt bei einer falschen Verwendung des
Produkts oder bei einer anderen Verwendung des Produktes
als für den vorgesehenen Zweck keinerlei Produkthaftung.
Marmitek übernimmt für Folgeschäden keine andere Haftung
als die gesetzliche Produkthaftung.

BoomBoom 55
17
DEUTSCH
3 Ihr Produkt
3.1 Einführung
Herzlichen Glückwunsch zum Erwerb des Marmitek BoomBoom
55. Mit diesem Bluetooth Audiosender können Sie den Ton Ihres
Fernsehers oder Ihrer Stereoanlage drahtlos an einen Bluetooth
Kopfhörer oder anderen (Bluetooth) Audioempfänger weiterleiten.
Die Lautstärke regeln Sie dann über Tonquelle (z.B. TV) oder
Audioempfänger (Bluetooth Kopfhörer).
Der BoomBoom 55 hat eine Reichweite von ca. 10 Metern,
sodass Sie Ihre Musik im selben Raum oder Nebenzimmer
genießen können.
HD Bluetooth Audiosender
Musik oder Ton Ihres Fernsehers mit Ihrem Bluetooth Kopfhörer
empfangen.
Ziehen Sie mehr Nutzen aus Ihrem Bluetooth Kopfhörer.
Genießen Sie Ihr Lieblingsfernsehprogramm oder Ihre Musik,
ohne andere zu stören.
Verfügt über digitale Audioeingänge und aptX® Technologie
für überragende Soundqualität.
Die beste Lösung für die Tonübertragung Ihres Fernsehers:
kein erkennbarer Unterschied zwischen Bild und Ton dank
der neuesten aptX Low Latency ® Technologie *).
Einmalige Möglichkeit, 2 Kopfhörer zugleich verwenden zu
können.
*)für beste Tonqualität sollte auch der Kopfhörer über “aptX Low Latency ®”
Technologie verfügen. aptX Low Latency funktioniert nur im Singlemode.
3.2 Verpackungsinhalt
A. 1 x BoomBoom 55, universeller, drahtloser Bluetooth
Stereotonsender.
B. 1 x Mini-Jack Audiokabel
C. 1 x Mini-Jack zum Cinch Audiokabel
D. 1 x Mikro USB Speisungskabel
E. 1 x USB Speisungsadapter
F. 1 x Gebrauchsanleitung

© MARMITEK
18
4 Produktübersicht
Mini-jack kabel
Dieses Kabel mit dem Audio-Input des BoomBoom 55 verbinden
Mini-Jack Konverterkabel
Mit diesem Kabel schließen Sie den BoomBoom 55 an den
Audioausgang (rechts-links) Ihres Fernsehers oder Ihrer
Stereoanlage an.
die Audio-
Kabelverbindung
Pairing-Taste
Micro USB-
Stromanschluss
Ein / Aus-
Schalter
TOSLINK
anschluss
Coax anschluss
Led status
A
B
C

BoomBoom 55
19
DEUTSCH
USB Speisungskabel
Dieses Kabel speist den BoomBoom 55 mit Strom.
USB Speisungsadapter
Schließen Sie D an E an und speisen
Sie den BoomBoom 55 mit Strom.
5 Led status
LED status
Beschreibung
Blaue LED blinkt schnell
Pairing Position
Blaue LED blinkt langsam
Suche nach letztem Gerät
Blaue LED leuchtet anhaltend
Verbunden
Grüne LED leuchtet stetig
aptX Low Latency Verbindung
6 Los geht’s
Befolgen Sie nachfolgende Schritte, um das Produkt in Betrieb zu
nehmen:
Schließen Sie den BoomBoom 55 an Ihre Stereoanlage an
Speisen Sie den BoomBoom 55 mit Strom
Paaren Sie den BoomBoom 55 mit einem Bluetooth
Kopfhörer
…und fertig!
Noch einmal alles Schritt für Schritt erklärt.
D
E

© MARMITEK
20
6.1 Anschluss an fernseher oder stereoanlage
Schließen Sie den BoomBoom 55 an den digitalen Audioausgang
(Toslink oder Koaxial) Ihres Fernsehers oder Ihrer Stereoanlage
an, um das beste Resultat zu erzielen.
Schließen Sie Ihr digitales Audiokabel (nicht enthalten) an
den digitalen Audioausgang Ihres Fernsehers oder Ihrer
Stereoanlage an.
Schließen Sie die andere Seite des Audiokabels an den
entsprechenden BoomBoom 55 Audioeingang an.
Schließen Sie das enthaltene USB Speisungskabel an den
POWER Anschluss des BoomBoom 55 und an den USB
Speisungsadapter an und verbinden Sie ihn mit der
Steckdose.
Sie können den BoomBoom 55 auch an den analogen
Audioausgang oder Kopfhörerausgang anschließen, wenn Ihr
Fernseher oder Stereoanlage keinen digitalen Audioausgang hat.
Schließen Sie eines der zwei enthaltenen Audiokabel an den
Audioausgang des Fernsehers oder der Stereoanlage an.
Schließen Sie die andere Seite des Audiokabels an den
BoomBoom 55 Audioeingang an.
Schließen Sie das enthaltene USB Speisungskabel an den
POWER Anschluss des BoomBoom 55 und an den USB
Speisungsadapter an und verbinden Sie ihn mit der
Steckdose.
6.2 Koppeln
1. Bringen Sie Ihren Bluetooth Kopfhörer nahe des BoomBoom
55. Die beste Entfernung beträgt ungefähr 1. Meter.
2. Schalten Sie Ihren Bluetooth Kopfhörer in den
Kopplungsmodus (sehen Sie dazu die Gebrauchsanleitung
Ihres Kopfhörers)
3. Stellen Sie den BoomBoom 55 Schalter auf ON und drücken
Sie die Pairing Taste. Die LED blinkt nun schnell.
4. Der BoomBoom 55 wird jetzt mit Ihrem Kopfhörer
automatisch Verbindung machen. Nachdem die Verbindung
hergestellt wurde, wird die LED am BoomBoom 55
unaufhörlich blau leuchten (das kann eine Weile dauern).