MARTINDALE VI13700G User manual

GENERAL SAFETY INFORMATION: Always read before proceeding.
Warning
These instructions contain both information and warnings that are
necessary for the safe operation and maintenance of this product. It is recommended that you
read the instructions carefully and ensure that the contents are fully understood. Failure to
understand and to comply with the warnings and instructions can result in serious injury,
damage or even death.
In order to avoid the danger of electrical shock, it is important that proper safety measures
are taken when working with voltages exceeding 30V AC RMS, 42V AC peak or 60V DC.
This product must only be used by a competent person capable of interpreting the results
under the conditions and for the purposes for which it has been constructed. Particular
attention should be paid to the Warnings, Precautions and Technical Specifications. Always
check the unit is in good working order before use and that there are no signs of damage to
it. Do not use if damaged.
Where applicable other safety measures such as use of protective gloves, goggles etc. should
be employed.
Remember: Safety is no accident
Warning
Before use check the unit for cracks or any other damage. Make sure the unit is free from dust,
grease and moisture. Also check any associated leads and accessories for damage. Do not use
if damaged.
NVerify the testers operation by using a known voltage before and after each use (e.g. the
PD690 proving unit). NB: The Martindale PD240 is not suitable for use with this voltage
indicator. Whilst verifying the unit, it is important to move the test lead around, and
ensure that the VI13700G display remains stable. This is necessary to confirm the
integrity of the cable.
INSTRUCTION
MANUAL
MARTINDALE
ELECTRIC
Trusted by Professionals
VI13700G
VOLTAGE INDICATOR
VI13700g voltage ind instruct rev5:instruct.qxd 10/03/2009 11:56 Page 1

Martindale Electric Company Limited
Metrohm House, Penfold Trading Estate, Imperial Way, Watford WD24 4YY, UK
Tel: [phone] Fax: [phone]
E-mail: [e-mail] Website: www.martindale-electric.co.uk
© Martindale Electric Company Ltd. 2009
Registered in England No. 3387451. Document Rev 5 LITVI
Trusted by Professionals
MAINTENANCE
Cleaning
The unit may be cleaned using a soft dry cloth. Do not use moisture, abrasives, solvents, or
detergents, which can be conductive.
Repair & Service
There are no user serviceable parts in this unit other than fuses. Return to Martindale Electric if faulty.
Before returned, please check the unit, fuses, leads and poor connections
Storage Conditions
The instrument should be kept in warm dry conditions away from direct sources of heat or sunlight.
~
~
+
+
VOLTAGE
RANGE 50 75 100 150 200 240 400 560
Light On
Light Off
OPERATION
1. Observe all safety recommendations
before use.
2. Apply the flying probe to the earth or lower
voltage terminal (if known) with one hand
ensuring fingers are behind the guard.
DO NOT TOUCH METAL TIPS.
3. Touch the fixed probe to the suspected live
terminal. Neons will strike progressively
to indicate the presence of AC or DC voltage.
SPECIFICATION
Voltage Range: 50 to 600V AC RMS
75 to 600V DC
Frequency Range: 0Hz to 400Hz & DC
Power Consumption: approx. 4W at 600V
approx. 0.4W at 230V
Temperature Range: -10°C to 40°C at max. 60% RH
Fuse Rating: 0.5A fast (600V)
Overvoltage Category: 600V Cat. 3
Pollution Degree: 2
Neon Strike Voltage Tolerance: -30% to +5%
NNever apply more than the rated voltage (600V max) between the probe tips.
NTry to use the unit with the retractable shrouds extended to minimise the risk of flashover.
NWhen using the probe ensure your fingers are behind the finger guard.
NDo not operate the tester around explosive gas, vapour or dust.
NEVER TOUCH THE EXPOSED METAL PROBE TIPS.
VI13700g voltage ind instruct rev5:instruct.qxd 10/03/2009 11:56 Page 2