MasterChef T420 User manual

T420 Barbecue
Assembly Manual
85-3004-2 (G45104) Propane
85-3005-0 (G45105) Natural Gas
1 YEAR LIMITED WARRANTY
READ AND SAVE MANUAL FOR FUTURE REFERENCE.
If pre-assembled, leave this manual with unit for
consumer’s future reference.
For product inquiries, parts, warranty and
troubleshooting support, please call 1-877-707-5463.
Manual Revision #: 25112009 PD

1
DANGER
1. If you smell Gas:
a. Shut o gas to the appliance
b. Extinguish any open ame
c. Open lid
d. If odor continues, keep away from
the appliance and immediately
call your gas supplier or your
re department
2. Requires two people to complete the
assembly process.
3. Beware of sharp edges.
WARNING
Failure to follow all of the Manufacturer’s
instructions could result in hazardous res,
explosions, property damage, or serious
personal injury or even death.
Follow all leak check procedures carefully
prior to operation of barbecue, even if grill
was dealer assembled. Do not try to light
this barbecue without reading the Lighting
Instructions section of this manual.
THIS MANUAL MUST REMAIN WITH THE PRODUCT AT ALL TIMES
CAUTION
Read and follow all safety statements,
assembly instructions, and use and care
directions before attempting to assemble
and cook.
WARNING
1. Do not store or use gasoline or other
ammable liquids or vapours in the
vicinity of this or any other appliance.
2. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
CAUTION
Sharp edges. Wear gloves when assembling
your grill.
THIS BARBECUE IS FOR OUTDOOR USE ONLY
CONTACT CALL CENTRE IF ANY PARTS ARE MISSING
1-877-707-5463
INSTALLER OR ASSEMBLER/CONSUMER
This manual should be kept with the BBQ at
all times.
HEAVY ARTICLE NEEDS 2 TO LIFT
TOOLS NEEDED FOR ASSEMBLY
• #2 Phillips screwdriver (long and short)
• ¼” Slotted screwdriver (long and short)
• Adjustable wrench
• Pliers
Before assembling the barbecue, read these
instructions carefully.
Assemble the barbecue on a at, clean surface.
Grill is heavy. You should have at least two people
assemble the barbecue together.
Notes: Do not fully tighten all the nuts during
this initial stage.
Caution:
Sheet metal can cause injury. Wear gloves when installing the grill.
HARDWARE PACK
¼” x 13mm Screw
X 10
Hitch Pin
X 1
Wing Screw
X 1
#8X3/8” Self Tapping Screw
X 14
Ø7 Fiber Washer
X 10
¼” - 20UNC Nut
X 8
Ø7Flat Washer
X 6
Wheel Spacer
X 2
Ø7Lock Washer
X 6
1 2 3
456
789
10
Washer (Wheel)
X 1
KEY # DESCRIPTION PART NUMBER QUANTITY
1 1/4” x 13mm Screw 20120-13013-036 10
2 Wing Screw G306-0025-9084 1
3 1/4”-20UNC Nut 31220-13000-036 8
4 #8X3/8” Self Tapping Screw 22500-42010-136 14
5 Ø7Flat Washer 40300-07000-036 6
6 Ø7 Fiber Washer G431-0018-9000 10
7 Wheel Spacer G305-0024-9088 2
8 Hitch Pin G306-0005-9088 1
9 Ø7Lock Washer 41400-07000-206 6
10 Washer (Wheel) 40300-08000-036 1
11 1/4” - 20UNCX18 Screw 20102-13018-036 4
11
1/4” x 18mm Screw
X 4
To ORDER non-warranty replacement parts or accessories, or to register your warranty,
please visit us on the web at
www.masterchefbbqs.com

23
PARTS LIST PROPANE FOR 8530042 G45104 EXPLODED DIAGRAM PROPANE FOR 8530042 G45104
KEY # QUANTITY DESCRIPTION PART NO.
AA 1 Top Lid assembly G451-0100-01
AB 1 Thermometer and Bezel G451-0008-01
AC 1 Logo plate G451-0001-01
AD 1 Top Lid Handle G413-0001-01
AE 2 Lid Bumbers- Back G303-0038-01
AF 2 Lid Bumbers- Front G430-00B8-01
AG 2 Screws for Lid G430-0024-01
BA 1 Burner Box Assembly G451-0200-01
BB 3 Burner G431-0300-01
BC 1 Electrode Set, main burners G501-0010-01
BD 2 Burner brace assembly G413-0004-01
BE 3 Flame Tamers G430-0005-01
BF 3 Cooking Grates G451-1200-01
BG 1 Warming Rack G430-0003-01
CA 1 Control Panel G451-0002-01
CB 1 Manifold Assembly G451-1000-01
CC 1 Regulator G402-0069-01
CD 3 Bezel, Control Knob G430-0027-01
CE 3 Control Knob G430-0026-01
CF1 1 Electronic Igntion Assembly G430-0008-01
CF2 1 Electronic Ignition Button G501-0072-A1
CG 1 Grease Cup Hook G305-0043-01
CH 1 Grease Cup G430-0033-02
DA 1 Cart side panel, right G451-0500-01
DB 1 Cart side panel, left G451-0400-01
DC 1 Back brace G431-0031-01
DD 1 Front panel G451-0005-01
DE 2 End Caps G431-0004-01
DF 1 Match Holder G401-0079-01
DG 2 Wheel cap G303-0020-01
DH 2 Wheel G210-0018-02
DI 1 Wheel Axle G430-0007-01
EA 1 Side Shelf table (right) G430-1500-01
EB 1 Side shelf fascia(right) G451-0003-01
EC 1 Side Shelf table (left) G430-2100-01
ED 1 Side shelf fasica (left) G451-0007-01
EE 1 Tank Exclusion G430-5402-01
EF 1 Tank retainer clip G306-0020-02
F1 1 Hardware Pack G451-B004-01
F2 1 Assembly Instructions G451-M004-01
F3 1 Safe Use and Care Manual G207-M015-02
AA
AB
AC
AD
DD
EA
EB
CG
CH
DA
DE
DC
DB
ED
EC
DG
EF
DH
DI
DG
DF
BG AF
AE
CB
CC
EE
BC
CF1 CF2
CD CE
CA
BA
BE
BF
BD
F2
F1 ASSEMBLY
MANUAL
F3
SAFETY
AND CARE
MANUAL
HARDWARE
PACK
AG
BB BD

4 5
PARTS LIST NATURAL GAS FOR 8530050 G45105 EXPLODED DIAGRAM NATURAL GAS FOR 8530050 G45105
KEY # QUANTITY DESCRIPTION PART NO.
AA 1 Top lid assembly G451-0100-01
AB 1 Thermometer G451-0008-01
AC 1 Logo plate G451-0001-01
AD 1 Top lid handle G413-0001-01
AE 2 Lid bumbers- back G303-0038-01
AF 2 Lid bumbers- front G430-00B8-01
AG 2 Screws for lid G430-0024-01
BA 1 Burner box assembly G451-0200-01
BB 3 Burner G431-0300-01
BC 1 Electrode set, main burners G501-0010-01
BD 2 Burner brace assembly G413-0004-01
BE 3 Flame tamers G430-0005-01
BF 3 Cooking grates G451-1200-01
BG 1 Warming rack G430-0003-01
CA 1 Control panel G451-0002-01
CB 1 Manifold assembly G451-1100-01
CC 1 Natural gas hose G501-0099-01
CD 3 Bezel, control knob G430-0027-01
CE 3 Control knob G430-0026-01
CF1 1 Electronic igntion assembly G430-0008-01
CF2 1 Electronic ignition button G501-0072-A1
CG 1 Grease cup hook G305-0043-01
CH 1 Grease cup G430-0033-02
DA 1 Cart side panel, right G451-0500-01
DB 1 Cart side panel, left G430-1000-01
DC 1 Back brace G431-0031-01
DD 1 Front panel G451-0005-01
DE 2 End caps G431-0004-01
DF 1 Match holder G401-0079-01
DG 2 Wheel cap G303-0020-01
DH 2 Wheel G210-0018-02
DI 1 Wheel axle G430-0007-01
EA 1 Side shelf table (right) G430-1500-01
EB 1 Side shelf fascia(right) G451-0003-01
EC 1 Side shelf table (left) G430-2100-01
ED 1 Side shelf fasica (left) G451-0007-01
F1 1 Hardware pack G451-B004-01
F2 1 Assembly instructions G451-M004-01
F3 1 Safe Use and Care Manual G207-M015-02
AA
AB
AC
AD
DD
EA
EB
CG
CH
DA
DE
DC
DB
EC
DG
DH
DI
DH
DG
DF
BG AF
AE
CB
BC
CD CE
CA
BA
BE
BF
BD
ED
AG
CF1 CF2
F2
F1 ASSEMBLY
MANUAL
F3
SAFETY
AND CARE
MANUAL
HARDWARE
PACK
CC
BB BD

6 7
Note: Turn Cart assembly upside down.
a. Place wheel (DH) and wheel spacer (#8) onto
wheel axle (DI). “Cone” side of wheel should be
against cart side panel.
Insert wheel axle assembly (DI) through wheel
axle hole in the front and rear, of the left cart
side panel (DB), as shown.
To complete wheel assembly, position the
wheel spacer (#7), wheel (DH), wheel washer
(#10) and hitch pin (#8), onto wheel axle (DI), as
shown.
PROPANE MODEL ONLY
Note: You will need two people for this step.
Assemble the tank exclusion (EE) to the left and
right cart side panels (DA, DB), as shown.
Note: The left cart side panel (DB) will have
large holes on the end of the legs for assem-
bling the wheel axle (DI).
Assemble the front panel (DD) to the left and
right cart side panels (DA and DB), as shown.
Ensure that the slots on the tank exclusion (EJ)
align with the slots on the front panel (DD).
NATURAL GAS MODEL WILL NOT
HAVE WIRETANK EXCLUSION EJ
SHOWN IN IMAGE.
Note: Turn Cart assembly over. Front panel
should be facing upward.
Assemble the back brace (DC) to the rear, left
and right cart side panels (DA, DB), as shown.
1 3
24
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
876
YOU WILL NEED:
YOU WILL NEED:
7
4
X 2
X 6
8
X 1
10
X 1
YOU WILL NEED:
4
X 4
b. Insert wheel cap (DG) into wheel (DH).
DB
DA
EE
EE
DA
DA DB
DD
DA
DB DC
DH
DH
DI
DG
Front View
Back View

8 9
5
6
Note: Stand cart assembly upright. TWO
PEOPLE required for this step. Ensure that the
regulator hose (Propane models only) is hang-
ing outside of cart.
Position the lid and burner box assembly (A&B),
onto the cart assembly (C), and assemble.
YOU WILL NEED:
YOU WILL NEED:
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
7RIGHT SIDE SHELF ASSEMBLY
a. Insert the right side shelf assembly hooks (EA
& EB) into the grooves located on the right
side of the burner box assembly (BA).
b. Ax the right side shelf table (EA) to the
burner box assembly (BA).
c. Ax the right side shelf fascia (EB) to the
control panel (CA).
Securely tighten all hardware.
Assemble the top lid handle (AD) to the top lid
assembly (AA).
11
X 4
1
X 2
5
X 4
5
X 2
6
X 2
9
X 4
9
X 2
YOU WILL NEED:
13
6
X 4 X 4
X 4
YOU WILL NEED:
4
X 2
AD
AA
EA
A B
+
C
BA

10 11
ASSEMBLY INSTRUCTIONS
8LEFT SIDE SHELF ASSEMBLY
a. Insert the left side shelf assembly hooks (EC
and ED) into the grooves located on the left
side of the burner box assembly (BA).
b. Ax the left side shelf table (EC) to the burner
box assembly (BA).
c. Ax the left side shelf fascia (ED) to the
control panel (CA).
Securely tighten all hardware.
YOU WILL NEED:
4
X 2
YOU WILL NEED:
13
6
X 4 X 4
X 4
EC
PROPANE MODEL ONLY
Insert and fasten the tank retainer clip (EF) into
the tank retainer bracket, located at the top,
center of the left cart side panel (DB).
Place the ame tamers (BE) into the burner box.
ASSEMBLY INSTRUCTIONS
9
10
YOU WILL NEED:
2
X 1
BE
EF
ED
CA

12 13
ASSEMBLY INSTRUCTIONS
11
12
Place the cooking grates (BF) into the burner box.
To assemble the warming rack (BG), insert the
stationary wire into the holes on the sides of the
lid. Insert warming rack pivot legs into the holes
on the inside of the burner box assembly, as
shown.
BF
BG
Stationary Wire
Pivot Legs
ASSEMBLY INSTRUCTIONS
13
14
Hang the grease cup hook (CG) from the bottom
of the burner box (BA), and place grease cup (CH)
into position.
PROPANE MODEL SHOWN
CAUTION
Failure to assemble grease cup hook and grease
cup will cause hot grease to drip from the
bottom of the BBQ burner box, with the risk of
re, property damage, or personal injury.
CAUTION
Cylinder valve must face to the front of cart
once the tank is attached.
Failure to install cylinder correctly may allow
gas hose to be damaged in operation, resulting
in re.
PROPANE MODEL ONLY
a. Propane tank collar must face to the front of
the BBQ. Loosen the wing nut from the tank
retainer clip (EK). Set bottom of the tank into
notches located on the bottom of the left cart
side panel (DB). Position tank retainer clip (EK)
onto tank collar and tighten wing nut.
WARNING
Always keep LP cylinder in upright position
during use, transport and storage.
ATTENTION: LP Cylinder is sold separately.
Use only LP tanks that are equipped with an
OPD (Overll protection device). Fill and Leak
check before attaching to the BBQ hose and
regulator. See Safe Use and Care Manual, leak
test procedure for more information
CG
CH

14
ASSEMBLY INSTRUCTIONS
15
16 Electronic ignition battery not included.
Unscrew the electronic ignition button (CF2) and
insert one AA battery into the electronic ignition
battery compartment (CF1), with the positive
end facing outward.
NATURAL GAS MODELS ONLY
Attach the natural gas hose (CC) to the side
burner valve tting, as shown.
ATTENTION: In order to complete installation
of your natural gas BBQ a 1/2” or 3/8” adapter
may be required to connect your BBQ’s natural
gas hose to your home gas supply. Contact your
natural gas supplier to purchase the necessary
part.
CC