Masterlock LFW082FTC User manual

Fire Safe Owner’s Manual
LFW082FTC, LFW123FTC, LTW123GTC, LFW205FYC, LTW205GYC
:Masterlock.eu/Safes
INSTRUCTIONS FOR USE .........................................................2
MODE D’EMPLOI..................................................................... 5
GEBRAUCHSANWEISUNG......................................................... 8
GEBRUIKSAANWIJZING...........................................................11
INSTRUCCIONES DE USO..........................................................14
ISTRUZIONI PER L’USO ............................................................17
INSTRUÇÕES DE UTILIZAÇÃO.................................................... 20
ΟΔΗΓΙΕΣ ΧΡΗΣΗΣ ................................................................... 23
BRUKSANVISNING.................................................................. 26
BRUGSANVISNING .................................................................29
KÄYTTÖOHJE.......................................................................... 32
BRUKSANVISNING..................................................................35
INSTRUKCJA UŻYCIA ............................................................... 38
HASZNÁLATI ÚTMUTATÓ.......................................................... 41
MOD DE UTILIZARE .................................................................44
NÁVOD K POUŽITÍ................................................................... 47
ИНСТРУКЦИЯ ПО ПPИMEHEHИЮ.............................................50
KULLANIM TALİMATI...............................................................53
使用説明書....................................................................... 56

2
ENGLISH
NOTE: • Make sure the handle is rotated all the way up in the
horizontal position before unlocking the safe.
• If the door does not open easily, repeat steps 1-5.
• If you exert too much force on the handle, the handle will
move without moving the bolts. If this happens, you will
hear a ’click.’ DO NOT be alarmed. This feature is designed
to protect the bolts from being overpowered by force. If this
occurs, simply exert force in the opposite direction (lifting up)
until the handles ’clicks’ back into place and repeat steps 1-5
to open your safe.
Locking your safe
1Close the door and pull the
handle upward until the handle
is horizontal.
For water-resistant units,
additional pressure to the front,
left side of the door may need to
be applied prior to rotating the
handle.
2Spin the dial at least 2x to the
right (clockwise).
3FOR DUAL KEY/COMBINATION
LOCKS ONLY, insert key into the
lock, turn to the ’locked’ position,
then remove the key.
Programmable Electronic Lock
NOTE: Store code (and keys if
equipped) in a secure location
(other than in the safe).
Preparing your safe for first time use
1Ensure any shipping screws have
been removed. Located on the
inside of the door.
NOTE: Your unit may or may not
have a shipping screw.
Fire Safe
Thank you for choosing Master Lock to store all your important documents and valuables.
We hope that this product will help you stay organized and provide you with the peace-of-mind of knowing the things most important to you are protected.
Warning
Gun warning
This product is not intended for the secure storage of all materials.
Items such as firearms, other weapons, combustible materials, or
medication should NOT be stored in this unit.
Warning
DO NOT store delicate items directly in your safe.
Master Lock products which offer fire protection have a proprietary
insulation that has a high moisture content. In addition, the Master
Lock advanced safes close airtight to offer water resistance, which
may also cause moisture to accumulate inside your safe. The desiccant
packet included in your safe during shipment should be left in your
safe. DO NOT DISCARD IT. It is intended to help absorb moisture which
may accumulate inside your safe. Please open your unit once every two
weeks to avoid moisture accumulation.
If you choose to store delicate items such as jewelry with working parts,
watches, stamps, or photos in your safe, we recommend putting them in
an air-tight container, prior to placing them in the safe for storage.
NOTE: Master Lock will not be responsible for any damage or loss of
items placed in the unit due to moisture.
Warning
DO NOT store pearls in this safe.
In the event of a fire, potential damage to delicate pearls occurs at
temperatures much lower than the 350°F (176°C) interior performance
measure which the UL classification performance standard indicated
guarantees. Therefore, DO NOT store pearls in your Master Lock product.
Warning
No computer disks, audio-visual cassettes or photo negatives.
This product is not intended to protect computer floppy or diskettes,
cartridges and tapes, audio or video cassettes or photo negatives.
Warning
Your safe is only part of your total security protection.
Master Lock recommends that you store your safe in closets, offices,
basements, bedrooms and any other locations that are convenient for
you but out of direct line of sight from prying eyes. The location of the
safe does not affect the safe’s ability to protect your valuables inside.
Important
If you experience any problems or challenges with your safe, please
contact us. Many issues can be resolved quickly without the product
being returned. www.masterlock.eu/safes
Mechanical Combination Lock
NOTE:
• Store combination (and keys if
equipped) in a secure location
(other than in the safe).
• Combination can not be
changed.
Preparing your safe for first time use
1Ensure any shipping screws have
been removed. Located on the
inside of the door.
NOTE: Your unit may or may not
have a shipping screw.
2
M100TEST
SN100TEST01*
10-22-33 RLR
2075
Find your combination on the back
of this owner’s manual.
WARNING: Test your combination several times before
putting valuables inside.
Unlocking your safe
1FOR DUAL KEY/COMBINATION
LOCKS ONLY, insert key into the
lock, turn to the ’unlocked’ position,
then remove the key
This is a secondary locking feature
not an override key.
2Rotate dial to ’0’, then rotate
right (clockwise) passing ’0’
three times, continue rotating
until you reach the first number
in your combination.
3Rotate dial to the left
(counterclockwise). Go PAST the
second number of your
combination ONCE and stop the
SECOND time the dial reaches the
number.
4Rotate the dial to the right
(clockwise), stop when you reach
the third number in your
combination.
5Rotate the handle downward to
open the door.
This may take a limited amount
of force if you have a water-
resistant safe.

3
ENGLISH
2A Slide out the battery drawer
on the side of the keypad.
B Insert 4 AAA alkaline
batteries (not included)
Note: Do not use rechargeable
batteries or any other type of
non-alkaline battery. Do not mix
old and new batteries. Do not mix
alkaline and standard batteries.
C Slide battery drawer back
into keypad.
3
M100TEST
SN100TEST01*
12345
Find your 5 digit factory code on
the back of this owner’s manual.
WARNING: Test your code several times before putting
valuables inside.
Unlocking your safe
1FOR DUAL KEY/COMBINATION
LOCKS ONLY, insert key into the
lock, turn to the ’unlocked’
position, then remove the key
This is a secondary locking
feature not an override key.
2A Enter the 5 digit factory code
found on the back of the
owner’s manual.
Note: You may have to lift
the handle while entering
the combination.
B A green light will indicate the
code is correct. You will have
4 seconds to turn the handle
to unlock your safe.
3Rotate the handle downward to
open the door.
This may take a limited
amount of force if you have a
water-resistant safe.
NOTE: • Make sure the handle is rotated all the way up in the
horizontal position before unlocking the safe.
• If you exert too much force on the handle, the handle will
move without moving the bolts. If this happens, you will
hear a ’click.’ DO NOT be alarmed. This feature is designed
to protect the bolts from being over powered by force. If this
occurs, simply exert force in the opposite direction (lifting up)
until the handles ’clicks’ back into place and repeat steps 1-3
to open your safe.
• Delay mode will occur if three consecutive invalid entries have
been tried. Red LED will blink on and off to let you know the
safe is in delay mode. This will cause the system to shutdown
for two minutes. DO NOT remove the batteries to restart the
system it will only increase the length of time for the system
shutdown.
Locking your safe
1Close the door and pull the
handle upward until the handle is
horizontal.
For water-resistant units,
additional pressure to the front,
left side of the door may need
to be applied prior to rotating
the handle.
2FOR DUAL KEY/ELECTRONIC
LOCKS ONLY, insert key into the
lock, turn to the ’locked’ position,
then remove the key.
NOTE: If your safe does not
appear to be working properly,
please check to make sure you
are using NEW alkaline batteries
before contacting Master Lock
Customer Service.
Programming information
Three code options:
Factory code:
The safe will ALWAYS unlock using
this 5 digit code (found on the back of
the owner’s manual). This code cannot
be deleted.
User code:
A 5 digit programmable code of your
choosing that can be changed or
deleted or changed.
Secondary code:
A second 5 digit programmable code of
your choosing that can be changed or
deleted. Can only be programmed after
a user code has been activated.
NOTE: • The “C” key is a clear key. This can be used at anytime to
clear the system and return to standby mode – unless you are
in delay mode (3 consecutive invalid entries).
• The 5 digit factory code cannot be deleted. However, you may
add and delete additional codes.
This safe can store up to three codes at one time. One factory
code and two additional programmable codes.
Programming the user code
To ADD a user code:
1Press the “P” key.
2Enter the 5 digit factory code found on the back of your owner’s
manual.
3The light will flash green and then you will have five seconds to
enter your own personal 5 digit user code.
To DELETE a user code:
1Press the “P” key.
2Enter the 5 digit factory code.
3Enter 0,0,0,0,0.
NOTE: • The electronic lock will NOT indicate that it has deleted the
user code – please test the code to make sure it has been
deleted.
• Test with door open when programming.
Programming the secondary code
To ADD a secondary code:
1Press the “P” key two times.
2Enter the 5 digit user code previously programmed.
3The light will flash green and then you will have five seconds to
enter your own personal 5 digit secondary code.
To DELETE a secondary code:
1Press the “P” key two times.
2Enter the 5 digit user code.
3Enter 0,0,0,0,0.
NOTE: • The electronic lock will NOT indicate that it has deleted the
secondary code – please test the code to make sure it has
been deleted.
How to operate the light
The safe you have purchased may include a light. This is a long-lasting
LED light. Not all safes include a light.
The batteries that operate the keypad
are the same batteries that operate the
light. If the light in your unit does not
turn on, please change your batteries.
The light will turn on every time you
enter your code and will remain on
for 30 seconds. The light duration has
three options – off, 30 seconds, and 60 seconds.
To turn the light off:
1Press the “0” button.
2Press the “P” button.
3Press the “3” button.
To turn the light on for 30 seconds:
1Press the “0” button.
2Press the “P” button.
3Press the “4” button.
To turn the light on for 60 seconds:
1Press the “0” button.
2Press the “P” button.
3Press the “5” button.
NOTE: • If the light duration is 60 seconds, the battery life will be
reduced at a faster rate.
Operating sound features
For Programmable Electronic Lock Only
The tones of the key pad may be turned on and off depending on user
preference.
Turn sound off:
1Press “O”.
2Press “P” key.
3Press “2”.
Turn sound on:
1Press “O”.
2Press “P” key.
3Press “1”.

4
ENGLISH
Bolt-down instructions
(For select models only)
WARNING: Product is not water resistant once it is bolted
down. The ETL verified water resistance claim applies to product
prior to the application of a bolt-down kit.
Bolt-down kit contents (in select models only):
• 2 lag screws
• 2 washers
• 2 masonry anchors
Tools needed to bolt safe to the floor:
• Drill
• Wrench
• 7⁄16” (11 mm) drill bit – for drilling into the safe
• 9⁄32” (7.2 mm) drill bit – for drilling into a wood floor
• 3⁄8” (9.5 mm) drill bit – for drilling into a masonry floor
WARNING: • DO NOT drill from any location inside the safe.
• DO NOT bolt through the walls.
1Tip the safe onto its right side (door hinges horizontal with the floor).
2
F
Unlock the safe and open the door.
Look to the bottom of the safe for
two indentations on the feet in
opposite corners. Using the 7⁄16”
(11 mm) bit; drill a hole through
each indentation perpendicular to
the bottom of the safe. DO NOT drill
from any location inside the safe.
3Tip the safe upright, place the safe in the desired location and
open the door.
4
F
Use a screw or pencil to mark the floor
through both holes.
5Move the safe aside to clear both marked spots for drilling.
6Drill into the floor:
F
A For wood: Using the 9⁄32” drill bit, drill
a hole 2-1⁄2” (64 mm) deep in each
marked spot.
B For masonry: Using the 3⁄8” drill bit,
drill a hole 2-1⁄2” (64 mm) deep in each
marked spot. Install a masonry anchor
in each hole.
7Replace the safe in the desired position, with the holes in the safe
aligned with those in the floor.
8Securing the safe:
F
A For wood: Pass each lag screw through a
washer, then through the safe and into a
hole. Tighten with the wrench.
F
B For masonry: Pass each lag screw
through a washer, then through the safe
and into a masonry anchor. Tighten with
the wrench. Place masonry anchors into
the holes in the floor.
NOTE: • The safe should not be bolted to a wall, this will compromise
the fire rating. Drill holes through the feet only. DO NOT drill
through the back or sides.
• Bolting/unbolting the unit is at the consumer’s expense and
discretion.
• Master Lock is not responsible for any costs incurred if the
unit is to be replaced.
Troubleshooting
THE PROBLEM: WHY IT IS HAPPENING: THE SOLUTION:
The door will not lock. 1. Shipping screw is in place.
2. Confirm that there is no obstruction in the door.
3. Bolted down incorrectly.
1. Remove the screw on the back inside of the door.
2. Remove all items and accessories from inside the safe.
If this resolves the issue, re-set the accessories and
organize items to properly fit.
The handle is not
in the horizontal
position when the safe is
locked.
The clutch mechanism has
been engaged.
Rotate the handle up or down until it clicks into the
horizontal position.
Cannot open door after
inputting the combination or
electronic code.
1. Safe doors equipped with a water-resistant
gasket may initially be tight.
2. Key lock is in the locked
position. (select models only)
1. Hold the handle up while inputting the code or dialing
the combination and then pull down on the handle.
2. If your safe is equipped with a key lock ensure that the
key is in the unlocked position. (select models only)
The dial does
not turn.
1. Shipping screw is still in place.
2. Locking bolts are not fully extended.
1. Remove the screw from the back of the door.
2. Ensure the handle is in the horizontal position.
Red indicator light blinks three
times and there are
three beeps.
An incorrect code has been entered. Verify code and re-enter. If the programmable code you
are using doesn’t work then use the factory code. If
successful re-program your programmable code.
Red indicator light blinks five
times and there are five beeps.
Keypad communication error. Visit masterlock.eu/safes
Red indicator light blinks once
and there is one beep.
Program button is pressed out of sequence.
-or-
5 seconds has lapsed between button entries.
Start over.
Red indicator light
is blinking.
An incorrect code has been entered three times
and system has entered delay mode.
Wait two minutes and start over.
Yellow indicator light is on. Battery power is low. -or- Battery may be the
wrong type.
Replace with new alkaline batteries.
Registration
masterlock.eu/safes
By registering your Master Lock product you can easily retrieve
forgotten codes, combinations or order new keys should they be lost.
Registering also ensures the best customer service should you have a
question or concern regarding your Master Lock product. By registering
your Master Lock product you can also be sure that in the unfortunate
circumstance of a fire you will be guaranteed your replacement safe
(provided official paperwork).
Lifetime After-Fire
Replacement Guarantee
If your Master Lock product is in a fire it will be sealed shut making
it necessary for it to be pried open. To help your family begin again,
Master Lock will ship a replacement free of charge. To be eligible for
the After-Fire Replacement Guarantee you (the original owner) must
register your product by visiting masterlock.eu/safes.
Got a question?
If you ever have any questions regarding your Master Lock product,
please visit our website masterlock.eu/safes.