MD SPORTS 58400 User manual

MODEL/MODELO: 58400
INSTRUCCIONES DE ARMADO
Please contact us before returning the product to the store.
Toll Free: 877-472-4296
Por favor póngase en contacto con nosotros antes de
devolver el producto a la tienda.
Número telefónico gratis: 877-472-4296

LIMITED 90 DAYS WARRANTY
1
This product is covered by a limited warranty that is effective for 90 days
from the date of purchase. The warranty covers any defects in parts and
workmanship.
This Limited Warranty gives you specific legal rights and you may also have
other rights which very from one state (province) to another.
If, during the limited warranty period, a part is found to be defective or
breaks, we will offer replacement part at no cost to you, the customer. The
only exceptions to the warranty include main frames, tabletops, playing
surfaces, batteries or tools.
The above warranty will not apply in cases of damages due to improper
usage, alteration, misuse, abuse, accidental damage or neglect.
Please Attention: Since you build all tables upside down, please inspect
table tops and playing surfaces right away before putting together.
“PLEASE SAVE THESE INSTRUCTIONS
AND PURCHASE RECEIPT!”
A PURCHASE RECEIPT (or other proof of purchase date) will be required
before any warranty service is initiated. All requests for warranty service can
be submitted by email, in writing or by contacting our Consumer service
Department at:
TOLL FREE: 877-472-4296
WEBSITE: www.medalsports.com.tw
*Please do not call our 800 NUMBER as well as email us. This will result in
duplicate orders and charges will occur.
*Please note that all damaged table tops need to be returned to the store.
We do not replace any tabletops or playing surfaces.
PLEASE CONTACT US BEFORE RETURNING THE
PRODUCT TO THE STORE. THANK YOU VERY MUCH!

Phillips Screwdriver – Not Included
Standard (Flat Head Screwdriver) – Not Included
Allen Wrench - Included
TOOLS REQUIRED:
ASSEMBLY TIPS:
:

!



!
2
IMPORTANT NOTICE! Please contact us before returning the product to the store.
Please read the instructions carefully, and follow all assembly, operation or safety instructions
properly in order to avoid damage or injury. For the assembly, at least two adults are required.
Some figures or drawings may not look exactly like your product. Please read and understand
the text before beginning each assembly step.
1 -
2 -
Please Keep Your Instructions! Your Model number is necessary should you need to contact
us. Please read through this instruction manual book to familiarize yourself with all parts and
assembly steps. Kindly refer to the parts identifier below and be sure that all parts have been
included.
Although we dedicated to giving our customers the best product possible, a question may
arise or parts may be missing. If you are missing parts, or, if you have any questions, please
contact our fast and friendly service centre on:
1 - This product is intended for INDOOR use only.
2 - Please Do Not sit, climb or lean on the game table.
3 - Please Do Not drag the table when moving it in order to avoid the damaged on the legs.
4 - Please only use spray furniture polish to clean the exterior surfaces on the game table.
5 - This is not a child's toy, adult supervision is required for children playing this game.
877-472-4296
Power Tools
- Set Low Torgue
High Torque
over tightened
CAUTION !
Electric Screwdrivers may be helpful during
assembly; however, please set a low torque
and use extreme caution.

3
6
11
2 3 4 51
7 8 9 10
12 13 14 15
16 17 18 19 20
21 22 23 24 25
26 27
34
28
29 30
31
36
32 33 35
PARTS IDENTIFIER
Pre-installed
Pre-installed Pre-installed
3.5 x 10mm Bolt
4 Pieces
Electronic Scorer
Face Plate
1 Piece
Ball Return with
Side Netting
1 Piece
Control Box
1 Piece
Wrench
1 Piece
Plastic Pole Insert
6 Pieces
Spring Lock
9 Pieces
Lock Pin
2 Pieces Allen Key
1 Piece
HOME VISITOR
TIME
37
Net Hanger Tube
2 Pieces
Vertical Board Support
Mounting Tube
2 Pieces
Left Vertical
Support Tube
1 Piece
Left Horizontal
Frame Brace Tube
1 Piece
Right Horizontal
Frame Brace Tube
1 Piece
Angle Top Frame
Support Tube
2 Pieces
Angle Bottom Frame
Support Tube
2 Pieces
Middle Ramp Tube
2 Pieces
Front Ramp Tube
2 Pieces
Paddle with Sensor
2 Pieces
Metal Net
2 Pieces
Rim Support Plate
2 Pieces
Rim with Metal Net
2 Pieces
Control Wire
1 Piece
Basketball
4 Pieces
Front Horizontal Ramp
Support Tube
1 Piece
Short Horizontal
Cross Brace(1.21m)
1 Piece
Long Horizontal
Cross Brace(1.25m)
1 Piece
Electronic Scorer
1 Piece
Backboard
1 Piece
M6 Washer
64 Pieces
M6 x 20mm Bolt
16 Pieces
M6 x 45mm Bolt
4 Pieces
M6 x 50mm Bolt
4 Pieces
M6 x 58mm Bolt
4 Pieces
M6 x 75mm Bolt
4 Pieces
M6 Nut
32 Pieces
Inflation Pump
with Needle
1 Piece
Right Vertical
Support Tube
1 Piece
38

4
ASSEMBLY INSTRUCTIONS
FIG. 1 & 2
FIG. 3
1. Find a clean, level place to begin the assembly of your Basketball Game. We recommend that two adults work
together to assemble this basketball game.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts
Identifier below.Carefully cut or tear the four corners of the box so that the bottom of the box can be used
as your work surface.
3．Attach the Vertical Board Support Mounting Tubes (#2) to the Left and Right Vertical Support Tubes (#3&#4)
using spring lock as shown in FIG.1.
4. Attach the Angle Top Frame Support Tubes (#7) to the Angle Bottom Frame Support Tubes (#8) using spring
lock as shown in FIG.2
5. Attach the Left and Right Horizontal Frame Brace Tubes (#5 and #6) together using spring lock as shown in FIG.3
FIG. 1
FIG. 2
2
2
34
5
6
FIG. 3
7
8
#36
Spring Lock
#36
Spring Lock
#36
Spring Lock

5
6. Attach the Horizontal Frame Brace Tube (#5 & #6) to Left and Right Support Tube(#3 & #4) using Bolts(#27),
Washers (#22) and Nuts(#28), and then attach the Horizontal Frame Brace Tubes(#5&#6) to the Angle Bottom
Support Tube (#8) using Bolts (#27), Washers (#22) and Nuts(#28) as shown in FIG4.
7. Attach the Angle Support Tubes (#7 & #8) to the Vertical Support Mounting Tube(#2) using Bolts(#24), Washers
(#22) and Nuts(#28) as shown in FIG4, repeat this step for other side. Note: Make sure the spring lock is face down.
8. Attach the Short Horizontal Cross Brace(#12) to the Vertical
Board Support Mounting Tube using Bolts(#25), Washers(#22)
and Nuts(#28) as shown in FIG5. And then insert the Net
Hanger Tubes (#1) to the Vertical Board Support Maunting
Tubes (#2) as shown in FIG.5.
FIG. 4
FIG. 5
FIG. 4
8
7
5
6
8
7
5
6
3
28
22
22
27
24
28
22
22
2
4
28
22
27
22
FIG. 5
12
1
2
1
22
28
25
22

6
9. Attach the Middle Ramp Tubes(#9) to Horizontal Frame Brace Tubes(#5 & #6) using Bolts(#25 ), Washers(#22)
and Nuts(#28) as shown in FIG 6.
10. Attach the Front Ramp Tubes(#10) to the Middle Ramp Tubes(#9) using spring lock as shown in FIG 7.
FIG. 6 & 7
9
FIG. 7
10
FIG. 6
#36
Spring Lock
22
28
25
22

7
FIG. 8 & 9
11. Attach the Rim Assemblies (#17) and Rim Support Plates (#18) to the Backboard (#21) using the Bolts (#23),
washers (#22) and Nuts (#28). And then attach the Switch and Paddle Assembly (#15) to the Backboard (#21)
using the Bolts (#23), washers (#22) and Nuts (#28). Make sure that you use washer on both sides of the
backboard as shown in FIG. 8.
12. Attach the Electronic Scorer Face Plate(#30) to the front of Backboard and connect with the Electronic Scorer(#14)
using Bolts(#29) as shown in FIG. 9.
FIG. 9
FIG. 8
23
22
51 71
15
17
23
22
21
28 22 81
28 22 81
14
29
30
TIME
VISITOR
HOME

8
FIG. 10
13. Slide elastic straps and sleeve of Ball Return with Side Netting (#35) onto Top Net Hanger Tubes as shown in
FIG. 10A & 10B.
14. Slide the Front Horizontal Ramp Support Tube(#11) into the sleeve of Ball Return with Side Netting(#35) as
shown in FIG. 10C.
15. Connect the Front Horizontal Ramp Support Tube(#11) to the Front Ramp Tube (#10) using spring lock as
shown in FIG. 10D.
16. Slide the Long Horizontal Cross Brace(#13) in front of the Ball Return with Side Netting(#35) and attach it
to the Front Horizontal Ramp Support Tube (#11) using Bolts(#24), Washers(#22) and Nuts(#28) as shown
in FIG.10E.
FIG.10
FIG.10D
FIG.10E
FIG.10C
FIG.10A
FIG.10B
11
35 35
35
11
10
28
24
13
22
11
#36
Spring Lock

9
FIG. 11
17. With the help of another adult, Attach the Backboard(#21) to the Top Net Hanger Tube(#1) using Bolts(#26),
Washers(#22) and Nuts(#28) as shown in FIG.11 A.
At each bottom hole of the backboard,attach the ramp tabs of Ball Return with Netting(#35) using Bolts(#26),
Washers(#22) and Nuts(#28) as shown in FIG.11 B .
18. Connect the Lock Pin (#31) to the Left & Right Frame Brace Tubes (#5 & #6) and insert it to the Left & Right
Frame Brace Tubes (#5 & #6) as shown in FIG. 11C.
22
22
28
26
Ramp Tab
12
21
1
35
Back View.
FIG. 11B
FIG. 11C
FIG. 11A
31
14
16
FIG. 12
FIG. 12
FIG. 12A
Sensor wire
Electronic Scorer
Sensor wire
19. Connect the Sensor Wire from Switch and Paddle Assembly to the Electronic Scorer (#14) as shown in FIG12.
and 12A. Connect the Control Wire (#16) to the Electronic Scorer (#14) as shown in FIG.12 and 12A.
Control Wire
ON/OFF
CONTROL
WIRE
VISITOR