MD SPORTS SG040Y20001 User manual

Assembly Instructions
MODEL
SG040Y20001
Menards
www.medalsports.com877-472-4296

- Not Included
RECOMMENDED
Power Tools: Set to Low Torque
High Torque: Over Tightened
Phillips Screwdriver
Electric Screwdrivers may be helpful during assembly; however, please set a low torque and
use extreme caution.
This product is intended for INDOOR use only.
Adult supervision is required for children playing this game.
1.
2.
IMPORTANT NOTICE!
Do not use or keep
product outdoors. For
indoor use only. No
wet/humid conditions.
Keep away from pets in
assembly area
No children in assembly
area
English
TOOLS REQUIRED
SG040Y20001 1(Continued on the next page) www.medalsports.com
ADULT ASSEMBLY REQUIRED.
CHOKING HAZARD - THIS ITEM CONTAINS SMALL PARTS. NOT SUITABLE FOR CHILDREN UNDER 3 YEARS.
DO NOT MODIFY THE PRODUCTS IN ANY WAY.
DO NOT AIM AT EYES OR FACE.
DO NOT POINT THE BLASTER AT PEOPLE OR ANIMALS.
THIS PRODUCT MAY BE MISTAKEN FOR AN ACTUAL FIREARM BY LAW ENFORCEMENT OFFICERS AND OTHERS.
ALTERING STATE OR FEDERAL REQUIRED MARKINGS OR COLORATION IN ORDER TO MAKE THE PRODUCT APPEAR
MORE REALISTIC AND/OR BRANDISHING OR DISPLAYING THE PRODUCT IN PUBLIC IS DANGEROUS AND MAY BE A
CRIME. DISPLAYING, EXHIBITING OR BRANDISHING IN A THREATENING MANNER AND POSSESSION, STORAGE OR
KEEPING ON SCHOOL PROPERTY ARE PROHIBITED ACTIVITIES. THE CRIMINAL PENALTIES MAY BE IMPRISONMENT
AND/OR FINES.
1.
2.
3.
4.
5.
6.
WARNING

FOR FIG. 2 FOR FIG. 2
Mainframe
1
x1
FOR FIG. 1
PART NUMBER FIG. NUMBER
QUANTITY
PART
PART NAME
English
PARTS IDENTIFIER
SG040Y20001 2(Continued on the next page) www.medalsports.com
Find a clean, level place to begin the assembly of your product.
Verify that you have all listed parts as shown on the part list pages.
1.
2.
BEFORE ASSEMBLY
4
x1
Blaster
ACCESSORIES
5
x10
Dart
A1
x2
Bolt
HARDWARE
FOR FIG. 2
ON/OFF
START
PLAYER
PLAYER1 TIME PLAYER2
FOR FIG. 3 FOR FIG. 3
P1
x1
Target - A
PRE-INSTALLED PARTS
P2
x1
Target - B
FOR FIG. 3
P3
x1
Target - C
Hanger
2
x1
FOR FIG. 2
Target Board
3
x1
FOR FIG. 1

ASSEMBLY
SG040Y20001 www.medalsports.com3(Continued on the next page)
English
FIG. 1
x1
1
1
x1
3
FIG. 2
x1
4
4
x1
2
x2
A1
A1
x10
5
5
5
ON/OFF
START
PLAYER
PLAYER1 TIME PLAYER2
2
Phillips Screwdriver
- Not Included
1
Back View
3

ASSEMBLY
SG040Y20001 www.medalsports.com4(Continued on the next page)
English
FIG. 3
P1
x1
x1
P2
Pre-installed
Pre-installed
x1
P3
Pre-installed
2
Door
2
Door
2
Spring Lock
2
Note: Hang the Skeet Shooting set on
the door, press the spring lock and pull
the support of the Hanger (2) to adjust
the height as shown in FIG. 3.
ON/OFF
START
PLAYER
PLAYER1 TIME PLAYER 2
P1
P2
P3

GAME DESCRIPTIONS
Press “ON/OFF START” to turn the game on. The LED will display “2P”. Press “PLAYER” to choose between 1 or 2 players.
In the 2 Player mode, after pressing “ON/OFF START” the LED will display a 5 second countdown. The indicator light will
show against PLAYER 1 and the target will move into position. After the sound finishes, the LED will countdown from 60
seconds. Each time the target is shot successfully, a sound is heard. PLAYER 1’s turn ends after the target has been shot 3
times, or the 60 seconds have elapsed.
For PLAYER 2’s turn, the LED will display a 5 second countdown. The indicator light will show against PLAYER 2 and the
target will move into position. After the sound finishes, the LED will countdown from 60 seconds. Each time the target is
shot successfully, a sound is heard. PLAYER 2’s turn ends after the target has been shot 3 times, or the 60 seconds have
elapsed. The time of the fastest player will blink and that player’s indicator light will turn on. If the times are equal, the times
will blink and both player indicator lights will turn on. If neither player has successfully completed the shots, then the display
will show “00”.
In the one player mode, after pressing “ON/OFF START” the LED will display a 5 second countdown. The indicator light will
show against PLAYER 1 and the target will move into position. After the sound finishes, the LED will countdown from 60
seconds. Each time the target is shot successfully, a sound is heard. PLAYER 1’s turn ends after the target has been shot 3
times, or the 60 seconds have elapsed. Then the LED displays a 5 second countdown, the target moves into position and the
game begins again. If the target is not shot within 2 minutes then the game turns off.
Press and hold “ON/OFF START” for 2 seconds to turn the game off.
If the game is inactive for a period of 5 minutes then it will turn off. There is no sleep mode.
1.
2.
3.
4.
5.
6.
Battery Box: Unscrew the bolt using a screwdriver and open the battery box. Insert 3x1.5v “AA” batteries ( not included) in
the sequence of polarity as shown on the inside cover. Then close the cover using a screwdriver.
BATTERY INSTALLATION
ELECTRONIC SCORER OPERATION
SG040Y20001 www.medalsports.com5(Continued on the next page)
English
The batteries must be installed according to their correct polarization (+ and -).
Please clean the battery contacts and also those of the device prior to battery installation.
If the game will not be used for a long period of time, we recommend removing the batteries.
a.
b.
c.
REMINDING:
Requires 3x1.5V AA batteries (not included).
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries.
1.
2.
3.
WARNING

English
DISCLAIMER
SG040Y20001 7(The last page) www.medalsports.com
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
This device complies with the Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and (2) This device must accept any interference received,
including interference that may cause undesired operation.
For additional resources, please contact Medal Sports Corp.
1300 Melissa Drive, Suite 124, Bentonville, AR 72712
Toll Free: 877-472-4296
NOTE
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
•
•
•

www.medalsports.com