Medel ADHEAR System User manual

Quick Guide
AW_. (English EU)
ADHEAR

Table of Contents
ADHEAR system .................................
Switching ADHEAR on/off ..........................
Changing the battery .............................
Applying the adhesive adapter ......................
Connecting the audio processor .....................
Disconnecting the audio processor..................
Changing the adhesive adapter.....................
Changing the program ...........................
Changing the volume ............................
Connecting ADHEAR to external devices ..............
ADHEAR accessories .............................
Basic care of the ADHEAR system ...................

Introduction
The ADHEAR Quick Guide contains easy-to-use instructions to get you
started with your ADHEAR.
For detailed information on the intended use, indications,
contraindications, warnings and precautions of the ADHEAR system,
please refer to the instructions for use.
©  MED-EL Elektromedizinische Geräte GmbH. Revision . (/).
All rights reserved.


ADHEAR
ADHEAR system
Audio input socket
Coupling plate
Battery compartment
Audio processor
Volume control
Adhesive adapter
Snap connector
Program button
Microphones


Switching ADHEAR on/off
Simply insert a battery and close
the battery compartment to
switch the audio processor on.
Make sure the plus sign (+) faces
upwards.
1To switch the audio processor off,
open the battery compartment
and/or remove the battery. Open
the battery compartment
whenever the audio processor is
not in use to extend battery life.
2


ADHEAR
Changing the battery
Remove the empty battery and insert a
new one (see page ). To activate the
battery, remove the plastic tab.
It is recommended to peel the tab off
the battery one to two minutes before
battery insertion. This time is needed
for the zinc-air battery to charge up
completely.
After closing the battery compartment,
there is a start-up delay of a few
seconds followed by an alert tone to
show that the device is ready to use.
Battery lifetime is usually one to
two weeks.
Only use size  zinc-air batteries
(also called PR batteries).


Applying the adhesive adapter
The skin behind the ear must be
clean, dry and free from any hair.
If the hairless area is not big
enough for the adhesive adapter,
adjust the hairline with a razor.
1Clean the skin with mild soap and
let it dry completely before you
apply the adhesive adapter.
2


ADHEAR
Place the adhesive adapter in the
positioning tool cavity.
3Remove the protective lm.
Do not touch the adhesive
surface.
4
The optional positioning tool can help you to correctly position the adhesive
adapter.


Find the correct position where
the tool is lightly touching the ear.
Make sure the adhesive adapter is
placed over bone.
5Press the tool rmly against the
skin.
6
Make sure that the application area is free from hair (see page ) and move any
hair away from the area.


ADHEAR
Gently remove the positioning
tool by moving it away from the
skin. Take care that you do not
pull against the adhesive adapter
when removing the tool.
7Press rmly on the entire surface
of the adhesive adapter for at
least  seconds.
8


Connecting the audio processor
Find the correct position and tilt
the audio processor onto the
snap connector from behind the
ear, while pressing on the
adhesive adapter.
1By pressing and rotating the audio
processor, the position may be
slightly adjusted. For optimal
performance make sure the audio
processor does not touch the
outer ear.
2


ADHEAR
Disconnecting the audio processor
To disconnect the audio processor
from the adhesive adapter, tilt it
towards your ear.
1Remove the audio processor
gently and do not pull on the
adhesive adapter.
2


Changing the adhesive adapter
Remove the adhesive adapter by slowly peeling it off the skin. The adhesive
adapter can usually be worn day and night and should be changed once or twice
a week. It is for single-use only.


ADHEAR
Changing the program
Press the program button to change the
program. The audio processor always
starts up in program  when it is
switched on.


Changing the volume
Scrolling away from the skin increases the volume.
Scrolling towards the skin decreases the volume.
Changes of volume are indicated by a beep.


ADHEAR
Connecting ADHEAR to external
devices
ADHEAR can be connected to different external devices, such as FM systems,
Telecoil receivers or smartphones. Connect the audio input cable to the external
device and the audio processor. Take care that the dots on the cable and on the
bottom side of the audio processor align.


ADHEAR accessories
Retention clip
The retention clip can be connected to
the audio processor with a loop. The clip
can be attached to clothing. A retention
clip is recommended during physical
exercise, sports, play and in other
situations when there is a risk of the
device falling off.
ADHEAR sleeve
The ADHEAR sleeve offers additional
protection, particularly for younger
users. It is simply pulled over the audio
processor.


ADHEAR
Cleaning
Basic care of the ADHEAR system
Follow these basic yet important care instructions to maintain your ADHEAR system.
The housing may be cleaned on the outside with soft baby wipes. Do not clean
the housing in or under water, to prevent water from entering the audio
processor. The coupling plate should be cleaned weekly with the cleaning brush
provided to remove dirt from inside the circular coupling plate groove. The gap
between the housing and the coupling plate should also be cleaned with the
cleaning brush.


Refer to your instructions for use for more information about cleaning, storage,
handling and disposal of the ADHEAR system.
If you live in a humid climate or perspire heavily, the audio processor should be
placed in a drying container (sold separately) instead of in the case when it is
not being worn.
Storage
Drying
When not in use, the device should be kept in the case provided. You can remove
the battery from the audio processor to extend battery life. You should always
remove the battery if you do not use the audio processor for a longer period of
time to avoid battery leakage and possible damage to the audio processor.
Store the adhesive adapters in a dry place at room temperature.


medel.com
MED-EL Elektromedizinische Geräte GmbH
Fürstenweg a,  Innsbruck, Austria
of[email protected]m