Medel RONDO User manual

RONDO®
Single-Unit Audio Processor
Quick Guide

RONDO®Single-Unit Audio Processor
Indicator Lights
Attachment Clip Fixture
(Available on both sides)
Microphone/
Microphone Cover
Battery
Pack
Switch Release Lever
Air Inlet
Control Unit
Table of Contents
Basic Assembly ........................... 2
Indicator Lights........................... 4
FineTuner ............................... 6
FineTuner Light Patterns .................... 8
Batteries................................ 9
Telecoil Accessories....................... 10
Mini Battery Pack ........................ 12
Assistive Listening Devices ................ 14
Accessories............................. 16
Basic Care and Maintenance ................ 18
Troubleshooting ......................... 20
UnlockedOFF/
Locked
ON
1

Basic Assembly
Install and lock the
magnet into the
control unit.
1Insert the batteries
with positive (+)
poles facing out.
2
Ensure the switch is set
to the unlock position.
Hold down the relase lever
while setting the switch to
unlock position.
3Slide the battery pack into
the control unit 1,push
down 2, and slide the switch
to locked position ( ).
4
The switch must always be
in the unlocked position
() prior to attaching to
the control unit.
RONDO
Installation
Unlock Lock
Note the mechanism
that secures the control
unit to the battery pack.
Hold down the
release lever.
1
Slide the switch
to unlock position
()and lift the
battery pack up.
2
Opening the Battery Pack
Removing Batteries
The bottom side of
the control unit can
be used to easily lift
batteries out of the
battery pack.
MED-EL strongly recommends
that you don’t change the magnet
yourself. Contact your clinician to
have the magnet changed or if
you experience any skin irritation.
11
22
Release
Lever
2 3

Status
Batteries are empty.
Either minimum or maximum volume
has been reached, or audio sensitivity
has been reached.
Warning
Problem
Temporary error or electronic
malfunction.
The setting you selected has not yet
been programmed, or there has been
a program malfunction.
Temporary error or electronic
malfunction.
Programming failure, temporary error,
or electronic malfunction.
Error Pattern Solution
1. Turn processor off.
2. Turn processor back on.
Select another setting.
1. Turn processor off.
2. Turn processor back on.
1. Turn processor off.
2. Turn processor back on.
Solution
Change the batteries.
Adjust volume or sensitivity
if necessary.
Status
FineTuner command has been successfully received.
Program 1 is selected.
Program 2 is selected.
Program 3 is selected.
Program 4 is selected.
Conrmation
If the optional status light has been activated:
RONDO is initialised and working.
Status
Program Change
Scale in Seconds
10 2 3
Scale in Seconds
10 2 3
Indicator Lights
RONDO4 5

Volume
Increase or decrease the volume
Program Selection
Choose a program
Default Volume and Sensitivity
Set volume and audio sensitivity
to default setting as determined
by your audiologist
Sensitivity
Increase or decrease the audio
sensitivity
Input Selection
M: Selects the microphone
MT: Selects microphone and telecoil
T: Selects the telecoil
Processor Selection
(For Bilateral Users)
Select the left processor, both
processors, or the right processor;
Activates and deactivates the
Keypad Lock
1
2
3
4
5
6
FineTuner
RONDO
Sensitivity
Input Selection
Processor Selection
(For Bilateral Users)
and Keypad Lock
Feature
Volume
Program
Selection
Indicator Lights
Default Volume
and Sensitivity
1
2
3
4
5
6
FineTuner Keypad Lock
To prevent accidental setting changes,
you can activate the FineTuner Keypad
Lock. If any key is pressed while the
keypad is locked, the red LED light on
the FineTuner will blink.
Temporarily Unlocking the Keypad
You can make a selection even when
the keypad is locked by pressing any
given key twice. The rst click
temporarily unlocks the keypad, and
the second click sends the command.
When the Keypad Lock is temporarily
deactivated, the keypad will relock
after 10 seconds of inactivity.
Activating the Keypad Lock
1. Press and hold the ( ) key for
5 seconds, or until the red and
amber lights blink alternately.
2. Press the ( ) key. When the keypad
has been locked successfully, the
amber lights will blink.
Deactivating the Keypad Lock
1. Press the ( ) key twice. The second
time, press and hold for at least
5 seconds, or until the red and
amber lights blink alternately.
2. Press the ( ) key. The amber lights
will blink to indicate that your
FineTuner is unlocked.
Any FineTuner key can be deactivated by your
clinician to prevent accidental setting changes.
6 7

+ 5 seconds
Meaning
Keypad is locked
Information is
being transmitted
Input side change
Programming mode
Batteries are low
Conguration has
been successful
Explanation
If you press any key while the FineTuner is locked,
the red indicator lights will turn on.
The indicator lights blink when signals are being
transmitted. The left light blinks if the left side is
activated. The right light blinks if the right side is
activated. Both blink if both sides (for bilateral users)
are activated.
Press the left key to send commands to the left side.
Press the right key to send commands to the right side.
The corresponding amber light will turn on. To send
commands to both sides (for bilateral users), press the
centre key. Both amber lights will turn on.
Press for more than 5 seconds to activate programming
mode. The 3 indicator lights will ash alternately.
If batteries are low, the red indicator light in the centre
will repeatedly blink three times.
If conguration of your FineTuner has been successful or
if the automatic keyboard lock feature has been either
activated or deactivated, both amber lights will turn on
for one second.
Light Pattern
Light Patterns
FineTuner
Batteries
Use only type 675 batteries to power your RONDO. We recommend using
zinc-air batteries that are designed especially for hearing implant systems.
When you use RONDO with the WaterWear accessory, however, you must
substitute zinc-air batteries with one of the other types.
675
Zinc-Air
Batteries
675
Silver-Oxide
Batteries
675
Alkaline
Batteries
675
Rechargeable
Batteries
Maximum battery life 75 hours 10 hours 8 hours 8 hours
Requires
oxygen supply
Yes No No No
Compatible
with WaterWear
No Yes Yes Ye s
RONDO8 9

Look for the symbol that identies
the use of an induction loop
system at venues.
For Neckloops and Silhouettes For Induction Loop Systems
Neckloop
Accessory
Microphone
with Telecoil Microphone
with Telecoil
Telecoil Only Telecoil Only
Microphone OnlyMicrophone Only
FineTuner Input
Selection Keys
FineTuner Input
Selection Keys
Telecoil Accessories
RONDO − Assistive Listening Devices
Insert the 3.5 mm
plug of the telecoil
accessory into the
headphone jack of
the audio device.
1Find the listening area of
the induction loop system
and stay within it.
1
Press the MT or T
button on your
FineTuner to activate
the telecoil and
select the input type.
2Press the MT or Tbutton on
your FineTuner to activate the
telecoil function and select
the input type.
2
Place the telecoil accessory
around your neck if you’re
using a neckloop or on
your ear if you’re using
a silhouette.
3
10 11

Mini Battery Pack
RONDO
RONDO Connector
Release Lever
Microphone
Test Device
Port (CS 44)
DaCapo
Rechargeable
Battery Compartment
AAA Battery
Compartment
3-Pin
FM Port
ON/OFF
and Battery
Compartment Lock
Basic Assembly
RONDO − Mini Battery Pack
Slide the MBP
connector into the
control unit.
1
Press the two release levers
and lift the connector up.
Connect the connector
cable to the M B P.
2
Removing
the Connector
Note the mechanism
that secures the control
unit to the battery pack.
The MBP can use either a single AAA battery
or a DaCapo rechargeable battery.
1
2
12 13

Direct Audio Input FM Receiver
Assistive Listening Devices
RONDO − Mini Battery Pack
Insert the 3-pin plug of the
audio adapter cable into the
FM port.
1Insert the FM receiver into the FM port.
RONDO will automatically detect sound
signals as soon as the FM system is
activated.
Insert the 3.5 mm plug
of the audio adapter cable
into the headphone port
of the audio device.
2
Refer to the user manual for your FM system
for instructions on changing FM settings.
Unilateral Mix
Audio Adapter
Cables
Unilateral Ext.
Bilateral Mix
Bilateral Ext.
14 15

Accessories
Attachment Clip
The attachment clip should be used to secure
RONDO to clothing or hair to reduce the risk of
losing or damaging the processor.
Fixation Loop for Glasses
The xation loop can be used to secure RONDO
to a pair of glasses or sunglasses.
RONDO Protector
The RONDO Protector is a soft silicone cover that
should be used to protect RONDO from fall damage
and other minor impacts.
WaterWear
WaterWear is a waterproof cover that provides
complete water protection for RONDO. Only
silver-oxide, alkaline, or rechargeable batteries
should be used with WaterWear.
RONDO16 17

Basic Care and Maintenance
Follow these basic and important care instructions to help improve the
functioning of your RONDO and extend its life.
General Cleaning
Clean RONDO regularly by wiping it with a soft, damp cloth. Don’t use cleaning
solutions. Use extra care when cleaning small parts such as the battery contacts.
Battery Contacts
Inspect the battery contacts regularly; clean and dry them as
necessary. To clean them, use a cotton swab and a small
amount of rubbing alcohol. Gently wipe them dry. Avoid
touching the battery contacts.
Moisture
Protect RONDO from exposure to water. If your audio processor gets wet,
gently wipe it dry with a soft absorbent cloth.
Sunlight
Don’t leave RONDO in direct sunlight, especially inside of a vehicle.
Don’t expose your audio processor to extreme temperatures.
Drying
Use the drying kit every night to allow RONDO to dry out
completely. Remove the battery pack cover before putting it into
the drying kit with your audio processor. Disposable batteries
can be left in the frame and put into the drying kit.
Refer to your user manual for more information
about care and maintenance.
RONDO
Don’t put rechargeable batteries
into the drying kit.
18 19

Troubleshooting
In case you encounter any minor technical problems, such as an
interruption in sound, carefully follow these steps to identify possible
causes and solutions:
1. Remove your RONDO and change the batteries. If that doesn’t solve the
problem, go to 2.
2. Disassemble your RONDO and check each part for dirt or signs of damage.
Gently clean any processor parts that are dirty and wipe dry any parts that
are wet. (See instructions on pages 22–23.) If any parts appear damaged,
contact your CI centre for assistance.
3. Reassemble RONDO. (See instructions on pages 2–3.) If your processor
still isn’t working, go to 4.
4. Use the Speech Processor Test Device to troubleshoot your audio processor.
Speech Processor Test Device
The Speech Processor Test Device (SPTD) is a
troubleshooting tool for detecting the most common
audio processor problems. To troubleshoot with the
SPTD, follow these steps:
1. Switch on your RONDO.
2. Place the at side of RONDO under the Speech Processor Test Device.
3. Speak into the RONDO microphones. The indicator light should icker to
the rhythm of your voice. If it doesn’t, go to 4.
4. Adjust the volume and speak into the microphones.
If the indicator light doesn’t icker, go to 5.
5. Change the batteries and speak into the microphones.
If the indicator light doesn’t icker, contact your CI centre.
For complete troubleshooting instructions, visit medel.com.
RONDO20 21

Notes Notes

Notes24

MED-EL Medical Electronics
Fürstenweg 77a | 6020 Innsbruck, Austria
ofc[email protected] medel.com
25225 r1.0