Media5 Mediatrix 4100 Series Manual

Pb
RoHS
COMPLIANT
2002/95/EC
Hardware Installation Guide
Mediatrix®4100 Series
Analog Access Devices
4108 / 4116 / 4124 models (FXS)
Product Version 2.0 Document Revision 07
December 12, 2009

Media5 Corporation Hardware Installation Guide
Media5 Corporation
4229 Garlock Street
Sherbrooke, Québec, Canada J1L 2C8
Mediatrix®4100 Series Hardware Installation Guide
© 2009, Media5 Corporation
Allrightsreserved.Nopartofthis publicationmaybe reproducedor used inanyform or by anymeans
–graphic, electronic,ormechanical,includingphotocopying,recording,taping,orinformation storage
and retrieval systems – without the express written permission of the publisher.
Media5 Corporation reserves the right to revise this publication and make changes at any time and
without the obligation to notify any person and/or entity of such revisions and/or changes.
Trademarks
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Adobe and Acrobat are registered trademarks of Adobe Systems Incorporated.
All other trademarks and registered trademarks are the property of their respective owners.
Third-Party Software Copyright Information
The Mediatrix®4100 Series firmware aggregates some third-party software modules (open source
and commercial) that are distributed to you in accordance with their respective licenses. Refer to the
Third Party Software Copyright Information addendum available on the Mediatrix Download Portal,
which lists the third-party software modules along with any copyright and license information.

Hardware Installation Guide
Mediatrix 4100 – Analog Access Device iii
Contents
Preface
About this Manual.............................................................................................................vii
Document Objectives.................................................................................................................................. vii
Intended Audience...................................................................................................................................... vii
Related Documentation............................................................................................................................. viii
Document Structure................................................................................................................................... viii
Document Conventions ...............................................................................................................................ix
Warning Definition.......................................................................................................................................................ix
Other Conventions ......................................................................................................................................................ix
SCN vs PSTN..............................................................................................................................................................ix
Standards Supported ..................................................................................................................................................ix
Obtaining Documentation.............................................................................................................................x
Media5 Web Site......................................................................................................................................................... x
Media5 Download Portal ............................................................................................................................................. x
Documentation Feedback ........................................................................................................................................... x
End User Technical Support.........................................................................................................................x
Chapter 1
Overview ..............................................................................................................................1
Overview.......................................................................................................................................................1
Key Features............................................................................................................................................................... 1
Mediatrix 4100 Connectors and Indicators ...................................................................................................2
Product Serial Number Location ................................................................................................................................. 2
Front Indicators and Connectors................................................................................................................................. 2
Rear Connectors ......................................................................................................................................................... 3
Port Numbering Convention .........................................................................................................................4
Mediatrix 4108/4116.................................................................................................................................................... 4
Analog Lines Numbering Convention (Mediatrix 4124)...............................................................................................4
Bypass Feature.............................................................................................................................................4
Chapter 2
Installation ...........................................................................................................................5
Planning the Installation................................................................................................................................5
Installation Checklist.................................................................................................................................................... 5
Site Log.......................................................................................................................................................................6
Network Information.................................................................................................................................................... 6
Safety Recommendations.............................................................................................................................7
Maintaining Safety with Electricity............................................................................................................................... 7
General Safety Practices............................................................................................................................................. 7
Preventing Electrostatic Discharge Damage............................................................................................................... 7
Required Mounting Tools and Equipment ....................................................................................................8
Unpacking and Inspection ............................................................................................................................8
Location and Mounting Requirements .........................................................................................................8
Location.......................................................................................................................................................................8
Rack-Mounting............................................................................................................................................................ 9
Free Standing Unit ...................................................................................................................................................... 9

Contents
iv Mediatrix 4100 – Analog Access Device
Condensation .............................................................................................................................................................. 9
Cleaning .................................................................................................................................................................... 10
Hardware Installation..................................................................................................................................10
Connecting Cables – Mediatrix 4108/4116 Models................................................................................................... 10
Connecting Cables – Mediatrix 4124 Model.............................................................................................................. 11
Chapter 3
Powering on the Mediatrix 4100.......................................................................................13
IP Address Discovery or Configuration.......................................................................................................13
Dynamic IP Address Discovery................................................................................................................................. 13
Default Static IP Address Configuration.................................................................................................................... 14
Special Vocal Features ............................................................................................................................................. 15
Verifying the Installation............................................................................................................................................ 15
Indicators (LEDs)........................................................................................................................................15
LED Patterns – Specific Conditions .......................................................................................................................... 15
LED Patterns – Default Behaviour ............................................................................................................................ 16
RESET/DEFAULT Button...........................................................................................................................17
At Run-Time.............................................................................................................................................................. 17
At Start-Time............................................................................................................................................................. 18
Partial Reset.............................................................................................................................................................. 18
Factory Reset............................................................................................................................................................ 19
Management Choices.................................................................................................................................19
Appendix A
Standards Compliance and Safety Information .............................................................21
Standards Supported..................................................................................................................................21
Disclaimers .................................................................................................................................................22
Federal Communications Commission (FCC) Part 15 .............................................................................................. 22
Federal Communications Commission (FCC) Part 68 .............................................................................................. 22
Industry Canada........................................................................................................................................................ 23
CE Marking................................................................................................................................................................ 23
RoHS China .............................................................................................................................................................. 24
Translated Warning Definition ....................................................................................................................25
Safety Warnings .........................................................................................................................................26
Circuit Breaker (15A) Warning .................................................................................................................................. 26
TN Power Warning.................................................................................................................................................... 26
Product Disposal Warning......................................................................................................................................... 26
No. 26 AWG Warning................................................................................................................................................ 26
LAN anf FXS Ports Connectors Warning.................................................................................................................. 26
Socket Outlet Warning .............................................................................................................................................. 26
Safety Recommendations...........................................................................................................................27
Appendix B
Cabling Considerations....................................................................................................29
RJ-45 Cable................................................................................................................................................29
Straight Through Cable............................................................................................................................................. 30
Crossover Cable........................................................................................................................................................ 31
RJ-11 (Telephone) Cable ...........................................................................................................................32
Wiring Conventions................................................................................................................................................... 32
RJ21X Connector (Mediatrix 4124) ............................................................................................................33
Creating a RJ21X Cable............................................................................................................................................ 33

Hardware Installation Guide
Mediatrix 4100 – Analog Access Device v
RJ21X Pinout ............................................................................................................................................................ 33
Loop Current vs Cable Length....................................................................................................................35
Appendix C
Standard Hardware Information.......................................................................................37
Industry Standard Protocols .......................................................................................................................37
Hardware Features.....................................................................................................................................38
Interfaces................................................................................................................................................................... 38
Power ........................................................................................................................................................................ 38
Product Architecture Details.......................................................................................................................38
Real Time Fax Router Technical Specifications.........................................................................................38
Analog Line Interface (FXS) .......................................................................................................................39
Audio Specifications ...................................................................................................................................39
DTMF Tone Detection ................................................................................................................................40
DTMF Tone Generation..............................................................................................................................40
Power Consumption ...................................................................................................................................40
MTBF Value................................................................................................................................................40
Operating Environment...............................................................................................................................41
Dimensions and Weight..............................................................................................................................41
Warranty.....................................................................................................................................................41
Appendix D
Glossary.............................................................................................................................43
Appendix E
List of Acronyms...............................................................................................................47

Contents
vi Mediatrix 4100 – Analog Access Device

Mediatrix 4100 – Analog Access Device vii
PREFACE
PAbout this Manual
Thank you for purchasing the Mediatrix 4100 Series from Media5 Corporation.
The Mediatrix 4100 Series FXS VoIP Integrated Access Devices are telephony adaptors that connect up to 24
conventional analog telephones or fax machines to a LAN or a WAN with access to an IP Packet Network to
permit high-quality, full duplex, audio/fax communications. The Mediatrix 4100 Series are available in the
following models:
Document Objectives
The Mediatrix 4100 Hardware Installation Guide provides technical information on how to physically install the
Mediatrix 4100. It also describes the cabling required for the Mediatrix 4100 device.
The information included in this guide consists of:
Hardware descriptions of the Mediatrix 4100 device
Hardware installation instructions
Installation scenarios examples
LED indications
Cabling and pin-out data
Please refer to the Dgw v2.0 Software Configuration Guide for software configuration information.
Use the Mediatrix 4100 Hardware Installation Guide in conjunction with the appropriate publications listed in
“Related Documentation” on page viii.
Intended Audience
This guide is intended for the following audiences:
Technicalstaffwhoarefamiliar withelectroniccircuitry,networking theoryandhaveexperience
as an electronic technician.
System administrators with a basic networking background and experience, but who might not
be familiar with the Mediatrix 4100 device.
Systemadministratorswho areresponsible forinstallingand configuringnetworkingequipment
and who are familiar with the Mediatrix 4100 device.
Table 1: Mediatrix 4100 Series Models
Model Interfaces
Mediatrix 4108 8 FXS ports
Mediatrix 4116 16 FXS ports
Mediatrix 4124 24 FXS ports
Note: There are many flavours of the Mediatrix 4100 device. Because of this, some of the information
provided may not apply to your particular Mediatrix 4100 device model.

Preface - About this Manual Related Documentation
viii Mediatrix 4100 – Analog Access Device
Related Documentation
In addition to this manual, the Mediatrix 4100 document set includes the following:
Dgw v2.0 Software Configuration Guide
Describes how to configure and operate the Mediatrix 4100.
Mediatrix 4100 Quick Start Guide
This printed booklet allows you to quickly setup and work with the Mediatrix 4100.
Configuration Reference Guide
Lists all the parameters, tables, and commands available in the Mediatrix 4100.
Notification Reference Guide
Lists and describes all syslog messages and notification messages that the Mediatrix 4100 may
send.
Third Party Software Copyright Information
This document lists the third-party software modules used in the Mediatrix 4100 along with any
copyright and license information.
Be sure to read any readme files, technical bulletins, or additional release notes for important information.
Document Structure
The Mediatrix 4100 Hardware Installation Guide contains the following information.
Table 3: Mediatrix 4100 Hardware Installation Guide Chapter/Appendices
Title Summary
“Chapter 1 - Overview” on page 1 Provides a brief description of the Mediatrix 4100.
“Chapter 2 - Installation” on page 5 Contains instructions for installing the Mediatrix 4100
and connecting the cables.
“Chapter 3 - Powering on the Mediatrix 4100” on
page 13 Leads you through the basic steps to start the Mediatrix 4100.
“Appendix A - Standards Compliance and Safety
Information” on page 21 Lists the various standards compliance of the
Mediatrix 4100.
“Appendix B - Cabling Considerations” on
page 29 Describes the pin-to-pin connections for cables used with the Mediatrix 4100.
“Appendix C - Standard Hardware Information”
on page 37 Lists the technical hardware information of the Mediatrix 4100.

Document Conventions Hardware Installation Guide
Mediatrix 4100 – Analog Access Device ix
Document Conventions
The following information provides an explanation of the symbols that appear on the Mediatrix 4100 and in the
documentation for the product.
Warning Definition
Where to find Translated Warning Definition
For safety and warning information, see “Appendix A - Standards Compliance and Safety Information” on
page 21.
This Appendix describes the international agency compliance and safety information for the Mediatrix 4100. It
also includes a translation of the safety warning listed in the previous section.
Other Conventions
The following are other conventions you will encounter in this manual.
SCN vs PSTN
In Media5’ and other vendor’s documentation, the terms SCN and PSTN are used. A SCN (Switched Circuit
Network) is a general term to designate a communication network in which any user may be connected to any
other user through the use of message, circuit, or packet switching and control devices. The Public Switched
Telephone Network (PSTN) or a Private Branch eXchange (PBX) are examples of SCNs.
Standards Supported
When available, this document lists the standards onto which features are based. These standards may be
RFCs (Request for Comments), Internet-Drafts, or other standards.
TheMediatrix4100’s implementationsare based on thestandards,soit’s possible that somebehaviourdiffers
from the official standards.
For more information on and a list of RFCs and Internet-Drafts, refer to the IETF web site at http://www.ietf.org.
Warning: Means danger. You are in a situation that could cause bodily injury. Before you work on any
equipment, you must be aware of the hazards involved with electrical circuitry and be familiar with standard
practices for preventing accidents.
Caution: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury and/or damage to the equipment or property.
Note: Indicates important information about the current topic.
Standards Supported Indicates which RFC, Draft or other standard document is supported for a
specific feature.

Preface - About this Manual Obtaining Documentation
xMediatrix 4100 – Analog Access Device
Obtaining Documentation
These sections explain how to obtain documentation from Media5.
Media5 Web Site
Media5 offers the latest version of its products’ documentation on its web site. You will thus be able to access
and download the most current Media5 documentation. Follow this link: http://www.media5corp.com/
categories.
Media5 Download Portal
Media5 offers online documentation via a self register web-portal. You will thus be able to access and
download the most current Media5 documentation. Follow this link to register: http://www.media5corp.com/
support/mediatrix--media5boss/support-portal.
Documentation Feedback
Media5 welcomes your evaluation of this manual and any suggestions you may have. These help us to
improve the quality and usefulness of our publications.
Please send your comments to:
Media5 Corporation
Attention: Documentation Department
4229, Garlock Street
Sherbrooke, Quebec
Canada J1L 2C8
Fax: [phone]
We appreciate your comments.
End User Technical Support
In order to maximize technical support resources, Media5 works through its partners to resolve technical
support issues. All end users requiring technical support are encouraged to contact their vendor directly.
Note: This site does not contain any firmware versions.
Note: This site does not contain any firmware versions.

Mediatrix 4100 – Analog Access Device 1
CHAPTER
1Overview
This chapter describes the Mediatrix 4100 connectors and indicators.
Overview
Provider-specific profiles ensurethatthe Mediatrix 4100 is a genuine plug and play solution. It offers a low total
cost of ownership as it reduces installation and maintenance costs. Moreover, the Mediatrix 4100 integrates
features such as TLS, SRTP, and HTTPS designed to bring enhanced security for network management, SIP
signalling and media transmission aspects.
The Mediatrix 4100 is a standalone Internet telephony access device that connects to virtually any business
telephone system supporting standard analog lines. The following are the Mediatrix 4100 Series models
currently available:
Key Features
IP connectivity for analog phones and faxes
Up to 24 simultaneous calls
FXS interface ports
HTTP, SNMP, FTP and TFTP for configuration and management
True Plug-and-Play
Automatic configuration script download
Call Routing service
Secure SIP signalling
Secure Media transmission
SNMPv3 and web management
DHCP Client
PPPoE Client
T.38 support
Command Line Interface (CLI)
SSL/TLS Encryption
Table 4: Mediatrix 4100 Series Models
Model Interfaces Bypass
Mediatrix 4108 8 FXS ports
Mediatrix 4116 16 FXS ports
Mediatrix 4124 24 FXS ports

Chapter 1 - Overview Mediatrix 4100 Connectors and Indicators
2Mediatrix 4100 – Analog Access Device
Mediatrix 4100 Connectors and Indicators
This section provides an overview of the front and rear panels of the Mediatrix 4100.
Product Serial Number Location
The serial number label for the Mediatrix 4100 device is located on the bottom of the unit.
Front Indicators and Connectors
See “Indicators (LEDs)” on page 15 for a description of the LED patterns the Mediatrix 4100 may have and
the states they represent.
Figure 1 shows the visual indicators and connectors located on the front of the Mediatrix 4108/4116/4124.
Figure 1: Mediatrix 4108/4116/4124 Front Panel Indicators
Table 6 describes the LEDs and connectors on the front panel of the Mediatrix 4100.
Table 6: Mediatrix 4108/4116/4124 Front Connectors and LEDs
Connector
/ LED Description
1. Ethernet RJ-45 connector for 100 BaseT Ethernet access to a LAN.
2. FXS
connectors Eight RJ-11 connectors to attach conventional telephones or G3 fax machines. These connectors are available on the Mediatrix 4116 only.
3. Analog
Lines A RJ21X connector with 24 RJ-11 Teladapt connectors to provide line cord connection to analog phones, faxes and modems. This connector is available on
the Mediatrix 4124 only.
See “RJ21X Connector (Mediatrix 4124)” on page 33 for more details.
2
1
1
1
3
4
4
56
7
8
9
10
56
7
8
9
10
56
7
8
9
10

Mediatrix 4100 Connectors and Indicators Hardware Installation Guide
Mediatrix 4100 – Analog Access Device 3
Rear Connectors
The Mediatrix 4108/4116/4124 models do not have rear connectors except for the IEC320-C14 Power Cord
Receptacle. This power cord supplies an internal Switching Mode Power Supply (SMPS) Universal input. The
power supply range is 100 – 240 VAC; 50/60 Hz; 1.6 A.The Mediatrix 4100 has several connections that must
be properly set. The following describes these connections for the various Mediatrix 4100 models.
Figure 2: Mediatrix 4108/4116/4124 Rear Panel Connectors
4. FXS
connectors Eight RJ-11 connectors to attach conventional telephones or G3 fax machines. These connectors are available on the Mediatrix 4108 and Mediatrix 4116 only.
5. Bypass Permits users to make and receive calls even when the Mediatrix 4100 is not
operating.
6. Ready LED When lit, the Mediatrix 4100 is ready to initiate or receive a call. The unit does not
have to be registered to a server.
7. In Use LED When lit, at least one of the FXS lines is in use.
8. LAN LED Provides the state of the network connected to the Ethernet connector.
9. Power LED When lit, power is applied to the Mediatrix 4100.
10. Reset /
Default
button
Resets configuration parameters of the Mediatrix 4100 to default (known) values. It
can be used to reconfigure the unit. See “RESET/DEFAULT Button” on page 17
for more details.
Table 6: Mediatrix 4108/4116/4124 Front Connectors and LEDs (Continued)
Connector
/ LED Description
Standards Supported • ITU-T I.430 Basic user-network interface - Layer 1
specification (section 9).
Rack-mounting
bracket
Universal Power Supply Unit

Chapter 1 - Overview Port Numbering Convention
4Mediatrix 4100 – Analog Access Device
Port Numbering Convention
Mediatrix 4108/4116
The following describes the port numbering conventions of the FXS connectors available on the Mediatrix
4108 and Mediatrix 4116. Note that the connectors in the left section are available only on the Mediatrix 4116
model.
Figure 3: FXS Connectors Port Numbering Convention (Mediatrix 4108/4116)
Analog Lines Numbering Convention (Mediatrix 4124)
The following describes the numbering conventions of the FXS analog lines available on the Mediatrix 4124.
Figure 4: Analog Lines Numbering Convention (Mediatrix 4124)
Bypass Feature
Duringnormaloperation,the SCN lineconnected totheBypass connector is switchedoutof the circuit through
commuting relays. The Bypass connector can be activated by two different conditions:
When power is removed from the Mediatrix 4100.
When the IP network is down.
This is indicated by the In Use LED being steady ON (except when the power is removed). If one of these
conditions is met, a phone/fax used on FXS connector 1 (Mediatrix 4108/4116) or analog line 1 (Mediatrix
4124) is directly connected to the SCN Bypass line. FXS connector 1 (Mediatrix 4108/4116) or analog line 1
(Mediatrix 4124) stays in Bypass connection until:
The error conditions have been cleared.
The device connected to it is on-hook and a delay has elapsed.
FXS
#16
FXS
#9
FXS
#15 FXS #13 FXS #11
FXS
#14 FXS
#12 FXS #10 FXS
#8
FXS
#1
FXS
#7 FXS #5 FXS #3
FXS
#6 FXS
#4 FXS #2
Analog Line #24 Analog Line #1

Mediatrix 4100 – Analog Access Device 5
CHAPTER
2Installation
This chapter describes the installation of the Mediatrix 4100.
Planning the Installation
Before installing the Mediatrix 4100, you should complete the following tasks:
Create a network diagram (see section “Network Diagram” on page 6).
Gather IP-related information (see section “IP-Related Information” on page 6 for more
information).
Install the hardware and software needed to configure the Mediatrix 4100 (see section
“Network Information” on page 6).
Installation Checklist
The installation checklist lists the tasks for installing the Mediatrix 4100. Print a copy of this checklist and mark
the entries as you complete each task. Include the completed checklist in your site log.
Figure 5: Installation Checklist
Mediatrix 4100 name/serial number _________________________________________________________
Task Verified By Date
Network information available & recorded in site log
Environmental specifications verified
Site power voltages verified
Installation site pre-power check completed
Required tools available
Additional equipment available
Mediatrix 4100 received
Quick start guide received
Regulatory compliance and safety information received
Warranty card received
Software version verified
Rack, desktop, or wall mounting of chassis completed
Initial electrical connections established
ASCII terminal attached to console port
Cable length limits verified
Initial configuration performed
Initial operation verified

Chapter 2 - Installation Planning the Installation
6Mediatrix 4100 – Analog Access Device
Site Log
Media5 recommends that you maintain a site log to record all actions relevant to the Mediatrix 4100, such as:
Installation: Print a copy of the installation checklist and insert it into the site log.
Upgrades and maintenance: Use the site log to record ongoing maintenance and expansion
history. Update the site log to reflect the following:
• Configuration changes
• Maintenance schedules, requirements, and procedures performed
• Comments, notes, and problems
• Software changes and updates to firmware
Network Information
When planning the installation of the Mediatrix 4100, you should consider the following network information.
Network Diagram
It is always good practice to draw a network overview diagram that displays all neighbouring IP nodes, serial
connected elements, and other components. It is recommended that you keep a copy in the site log (see “Site
Log” on page 6 for more information on keeping a site log).
IP-Related Information
Before you can install the Mediatrix 4100, you need to have the following information:
IP addresses and subnet mask used for the Ethernet WAN connector
IP addresses of the central SIP server
IP addresses of the central server used for configuration upload and download
Power Source
If you suspect that your AC power is not reliable, for example if room lights flicker often or there is machinery
with large motors nearby, have a qualified professional test the power. Install a power conditioner if necessary.

Safety Recommendations Hardware Installation Guide
Mediatrix 4100 – Analog Access Device 7
Safety Recommendations
The following are safety recommendations and best practices to follow when working with the Mediatrix 4100.
Maintaining Safety with Electricity
General Safety Practices
Follow these guidelines to ensure personal safety and protect the equipment:
Keep the Mediatrix 4100 clear and dust-free during and after installation.
Locate the emergency power-off switch for the room in which you are working. Then, if an
electrical accident occurs, you can act quickly to turn off the power.
Disconnect all power before installing the Mediatrix 4100.
Do not work alone if potentially hazardous conditions exist.
Never assume that power is disconnected from a circuit. Always check.
Do not perform any action that creates a potential hazard to people or makes equipment
unsafe.
Preventing Electrostatic Discharge Damage
Always follow electrostatic discharge (ESD) prevention procedures when installing or working around the
Mediatrix 4100.
Ensure that the Mediatrix 4100 chassis is electrically connected to earth ground.
Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the clip
to earth ground to channel unwanted ESD voltages to ground safely. If no ESD wrist strap is
available, ground yourself by touching the metal part of the chassis.
Warning: Do not work on the Mediatrix 4100, connect or disconnect cables during periods of lightning
activity.
Warning: Disconnect all power before servicing the Mediatrix 4100.
Warning: Hazardous network voltages might be present in WAN, LAN, and telephone networks
connectors regardless of whether power to the device is OFF or ON. Use caution when working near these
connectors to avoid electric shock. When detaching cables, detach the end away from the Mediatrix 4100
first.
Warning: This equipment must be installed and maintained by service personnel. Incorrectly connecting
this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be
disconnected before unplugging the main power connector.

Chapter 2 - Installation Required Mounting Tools and Equipment
8Mediatrix 4100 – Analog Access Device
Required Mounting Tools and Equipment
You will need the following tools and parts to properly install the Mediatrix 4100:
Screwdriver as required for attaching brackets to rack or wall.
Philips screwdriver for attaching brackets to the Mediatrix 4108/4116/4124.
Screws and anchors for wall-mounting, if required.
• Four wood screws or other fasteners, for installing the chassis on a wall.
ESD-preventive wrist strap.
In addition, you might need the following external equipment:
Modem for remote access.
RJ-45 cables for the WAN and LAN connections.
Unpacking and Inspection
If you haven’t already done so, unpack the Mediatrix 4100 device. Carefully remove it from the package and
packing material. The Mediatrix 4100 package contains the following items:
1 x Mediatrix 4100 unit
1 x power cord for the country in which you are using the Mediatrix 4100
2 x rack-mounting brackets
1 x BumponTM kit for desktop use
1 x Quick Start booklet
1 x Printed Flyer
1 x Warranty Card
You may also need additional 10/100 BaseT Ethernet RJ-45 cables.
Location and Mounting Requirements
The Mediatrix 4108/4116/4124 is suitable for use in an office environment where it can be placed in the same
room or cabinet where the PBX/telephony equipment is located. The unit can be mounted on a standard 48.26
cm (19 in.) equipment rack.
Location
Install the Mediatrix 4100 in a well-ventilated location where it will not be exposed to high temperature or
humidity. Do not install the Mediatrix 4100 in a location exposed to direct sunlight or near stoves or radiators.
Excessive heat could damage the internal components.
When deciding where to position the Mediatrix 4100, ensure that:
The Mediatrix 4100 is accessible for future upgrade, maintenance and troubleshooting, and
cables can be easily connected.
Warning: The analog lines of the Mediatrix 4100 are not intended for connection to a telecommunication
network that uses outside cable.
Warning: To prevent fire or shock hazard do not expose the unit to rain or moisture.

Location and Mounting Requirements Hardware Installation Guide
Mediatrix 4100 – Analog Access Device 9
The cabling is away from the following:
• Sources of electrical noise such as radios, transmitters, and broadband amplifiers.
• Power lines and fluorescent lighting fixtures.
• Water or moisture that could enter the casing of the Mediatrix 4100.
The airflow is not restricted around the Mediatrix 4100 or through the vents of the unit. The unit
requires a minimum of 25 mm (1 in.) clearance.
The fan on the Mediatrix 4100 is not blocked or that the rear of the unit is not too close to the
wall. The unit requires a minimum of 25 mm (1 in.) clearance.
The operating temperature is between 0oC and 40oC.
The humidity is not over 85% and is non-condensing.
Wiring Requirements
Make sure that the telephone wiring, LAN and WAN cables reach the device and can be dressed in a manner
that is safe for the wiring, does not pull or create lateral stress on the connectors on the device, and does not
present a trip hazard to personnel working in the vicinity of the equipment. Do not connect any cable or wiring
at this time.
Rack-Mounting
The Mediatrix 4100 fits in most standard 48.26 cm (19 in.) racks. Media5 recommends to use a rack compliant
EIA-310-D.
To rack-mount the Mediatrix 4100:
1. Disconnect all of the cables from the Mediatrix 4100, if applicable.
2. Insert the Mediatrix 4100 into the rack and secure with suitable screws (not provided). Be sure that
the fan is not obstructed.
To prevent bodily injury when mounting or servicing the Mediatrix 4100 in a rack, ensure that the
rack remains stable. The following guidelines are provided to ensure your safety:
• Mount the Mediatrix 4100 at the bottom of the rack if it is the only unit in the rack.
• When mounting the Mediatrix 4100 in a partially filled rack, load the rack from the
bottom to the top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting or
servicing the Mediatrix 4100 in the rack.
3. Proceed to “Hardware Installation” on page 10.
The Mediatrix 4100 has two screw holes on its bottom surface, allowing a single unit to be wall-mounted.
Free Standing Unit
When installing the Mediatrix 4100 on a desk or table, it should be located at least 20 cm from your monitor,
computer casing or other peripherals, including speakers. Never put books or paper on the Mediatrix 4100.
You must also apply the BumponTM authoadhesive protective products to the bottom of the Mediatrix 4100.
These will stabilize the Mediatrix 4100 and offer skidding resistance.
Condensation
When bringing the unit into a warm environment from the cold, condensation may result that might be harmful
to the unit. If this occurs, allow the unit to acclimatize for an hour before powering it on.
Standards Supported • EIA-310-D
• ETS 300 119

Chapter 2 - Installation Hardware Installation
10 Mediatrix 4100 – Analog Access Device
Cleaning
To clean the Mediatrix 4100, wipe with a soft dry cloth. Do not use volatile liquids such as benzine and thinner
that are harmful to the unit casing.
For resistant markings, wet a cloth with a mild detergent, wring well and then wipe off. Use a dry cloth to dry
the surface.
Hardware Installation
This section describes how to set the connectors of the Mediatrix 4100.
See “Appendix B - Cabling Considerations” on page 29 for more details on the cables the Mediatrix 4100 uses.
Connecting Cables – Mediatrix 4108/4116 Models
The following describes how to connect the various cables to the Mediatrix 4108 or Mediatrix 4116.
Figure 6: Mediatrix 4108/4116 Hardware Installation
To install the cables:
1. Before you begin, be sure that the Mediatrix 4100 is powered off.
2. Connect the power cord to its connector on the rear of the unit. Do not yet connect the other end of
the power cord to an electrical outlet.
3. Connect analog telephones or fax machines into the phone/fax connectors
The Mediatrix 4108 has 8 connectors, while the Mediatrix 4116 has 16 connectors.
Use a standard telecommunication cord with a minimum of 26 AWG wire size.
Warning: Do not connect the Mediatrix 4100 directly to Telecommunication Systems.
Caution: The Mediatrix 4100 must be installed on a circuit equipped with a breaker so that you can easily
power the unit off if required.
35
4
3
3
45
Note: The Mediatrix 4100 telephone line interface has been designed to interface with a conventional
telephone or fax machine. Connections to FXS ports of third party devices such as a PBX / Key System
could damage the Mediatrix 4100.