MeiTrack MS02 User manual

MEITRACK MS02 User Guide
MEITRACK MS02 User Guide

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 2 -
Change History
File Name
MEITRACK MS02 User Guide
Created By
Renny Lee
Project
GPS Tracking System
Creation Date
Update Date
2010-05-25
2014-09-23
Subproject
MS02
Total Pages
50
Version
V2.9
Confidential
External Documentation

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 3 -
Contents
1 Copyright and Disclaimer...............................................................................................................................................................- 5 -
2 Introduction...................................................................................................................................................................................- 5 -
3 Quick Start.....................................................................................................................................................................................- 5 -
3.1 Configuring GPRS Parameters.............................................................................................................................................- 5 -
3.1.1 Configured By Using Software .................................................................................................................................- 5 -
3.1.2 Configured By Running SMS Commands..................................................................................................................- 7 -
3.2 Logging In to the MS02 .......................................................................................................................................................- 8 -
3.3 Adding a Device ..................................................................................................................................................................- 9 -
3.4 Checking Status Updates ..................................................................................................................................................- 11 -
4 Software Functions......................................................................................................................................................................- 11 -
4.1 System ..............................................................................................................................................................................- 11 -
4.1.1 Language................................................................................................................................................................- 11 -
4.1.2 Skin ........................................................................................................................................................................- 11 -
4.1.3 Time Zone ..............................................................................................................................................................- 11 -
4.1.4 Logout....................................................................................................................................................................- 11 -
4.2 Management ....................................................................................................................................................................- 12 -
4.2.1 Admin ....................................................................................................................................................................- 12 -
4.2.1.1 Adding a Device ..........................................................................................................................................- 12 -
4.2.1.2 Adding an Existing Device ...........................................................................................................................- 12 -
4.2.1.3 Removing a Device......................................................................................................................................- 14 -
4.2.2 Tracker Customization............................................................................................................................................- 14 -
4.2.2.1 Customizing an Alarm .................................................................................................................................- 15 -
4.2.2.2 Customizing Status......................................................................................................................................- 16 -
4.2.2.3 Customize a Sensor.....................................................................................................................................- 17 -
4.2.3 Customizing a Temperature Sensor .......................................................................................................................- 17 -
4.2.4 Setting a Fuel Sensor..............................................................................................................................................- 18 -
4.2.5 Setting a LED ..........................................................................................................................................................- 19 -
4.2.6 Setting Parameters.................................................................................................................................................- 20 -
4.2.7 Geo-fence ..............................................................................................................................................................- 21 -
4.2.8 RFID Functions .......................................................................................................................................................- 25 -
4.2.9 Online Upgrade......................................................................................................................................................- 26 -
4.3 Querying a Report.............................................................................................................................................................- 27 -
4.3.1 Alarm Report..........................................................................................................................................................- 27 -
4.3.1.1 Search Criteria ............................................................................................................................................- 28 -
4.3.1.2 Search .........................................................................................................................................................- 28 -
4.3.2 Historical Data Report............................................................................................................................................- 29 -
4.3.3 Speed Report (Pie Chart) .......................................................................................................................................- 30 -
4.3.4 Speed Report (Line Chart)......................................................................................................................................- 31 -
4.3.5 Parking Report .......................................................................................................................................................- 32 -
4.3.6 Distance Report .....................................................................................................................................................- 32 -
4.3.7 Distance Statistics Report ......................................................................................................................................- 33 -
4.3.8 Sensor Report ........................................................................................................................................................- 34 -

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 4 -
4.3.9 Sensor Average Value Report.................................................................................................................................- 35 -
4.3.10 Platform Information ...........................................................................................................................................- 35 -
4.3.11 Input Status Report..............................................................................................................................................- 36 -
4.3.12 Vehicle Driver RFID Report...................................................................................................................................- 36 -
4.3.13 Photo Report........................................................................................................................................................- 37 -
4.3.14 Vehicle Maintenance ...........................................................................................................................................- 38 -
4.4 Query................................................................................................................................................................................- 39 -
4.4.1 Querying a Location...............................................................................................................................................- 39 -
4.4.2 Querying a Path .....................................................................................................................................................- 40 -
4.4.3 POI .........................................................................................................................................................................- 41 -
4.4.3.1 Querying a POI ............................................................................................................................................- 41 -
4.4.3.2 Adding a POI ...............................................................................................................................................- 42 -
4.4.3.3 Editing a POI................................................................................................................................................- 42 -
4.4.3.4 Deleting a POI .............................................................................................................................................- 43 -
4.4.3.5 Displaying a Selected POI............................................................................................................................- 43 -
4.4.3.6 Hiding POIs..................................................................................................................................................- 43 -
4.4.3.7 Displaying All POIs.......................................................................................................................................- 43 -
4.4.3.8 Exporting POIs.............................................................................................................................................- 43 -
4.5 Control Panel ....................................................................................................................................................................- 44 -
4.5.1 Device ....................................................................................................................................................................- 44 -
4.5.1.1 Toolbar........................................................................................................................................................- 44 -
4.5.1.2 Device List ...................................................................................................................................................- 45 -
4.5.2 Sending a Command..............................................................................................................................................- 45 -
4.6 Status Bar..........................................................................................................................................................................- 46 -
4.6.1 Status .....................................................................................................................................................................- 46 -
4.6.2 Alarm .....................................................................................................................................................................- 46 -
4.6.3 Uploading a Report ................................................................................................................................................- 46 -
5 MS02 Mobile Phone Version .......................................................................................................................................................- 47 -

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 5 -
1Copyright and Disclaimer
Copyright © 2014 MEITRACK. All rights reserved.
and are trademarks that belong to Meitrack Group.
The user manual may be changed without notice.
Without prior written consent of Meitrack Group, this user manual, or any part thereof, may not be reproduced for any
purpose whatsoever, or transmitted in any form, either electronically or mechanically, including photocopying and recording.
Meitrack Group shall not be liable for direct, indirect, special, incidental, or consequential damages (including but not limited to
economic losses, personal injuries, and loss of assets and property) caused by the use, inability, or illegality to use the product
or documentation.
2Introduction
The MS02, Meitrack GPS Tracking System, is a server-based online positioning tracking platform. The MS02 can monitor people,
articles, and vehicles installed with trackers in real time on web pages. This facilitates remote management. The MS02 can view,
remotely control, analyze, and collect statistics on historical data.
3Quick Start
3.1 Configuring GPRS Parameters
The GPRS parameters can be configured in any of the following ways:
3.1.1 Configured By Using Software
1. Configure the GT30i, GT60, VT300, VT310, and VT400 by using Parameter Editor.
GPRS:Select TCP.
GPRS Interval:Set the interval for regularly reporting General Packet Radio Service (GPRS) data. The interval unit is 10
seconds. 6, which indicates 1 minute, is recommended.
Tracker ID:The device ID will be displayed automatically after all data is read.
APN,APN Username, and APN Password:If the device is used in China, the Access Point Name (APN) of China Mobile is
CMNET, the APN of China Unicom is UNINET, and no user name and password exists.
IP:Set the active server IP address. The Meitrack server IP address is 67.203.13.26.
Port:Set the Transmission Control Protocol (TCP) or IP port for receiving GPRS data. The Meitrack server port is 8800.
2. Configure the MT80i, MT88, MT90, MVT340, MVT380, MVT600, and T1 by using Parameter Editor.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 6 -
GPRS:Select TCP.
GPRS Interval:Set the interval for regularly reporting GPRS data. The interval unit is 10 seconds. 6, which indicates 1
minute, is recommended.
GPRS Interval (ACC OFF): Set the interval for regularly reporting GPRS data when the engine is disabled. The interval unit
is 10 seconds. This option is unavailable for MT80i and MT88. To use this feature, the device must be connected to an
engine.
IP:Set the active server IP address. The Meitrack server IP address is 67.203.13.26.
Port:Set the TCP or IP port for receiving GPRS data. The Meitrack server port is 8800.
Secondary IP and Port:This feature is available for users with multiple servers. When the active server fails, device data
will be sent to the standby server automatically. Leave the two options blank if no standby server exists.
APN,APN Username, and APN Password:If the device is used in China, the APN of China Mobile is CMNET, the APN of
China Unicom is UNINET, and no user name and password exists.
Tracker ID:The device ID will be displayed automatically after all data is read. The ID is unique and must be consistent
with International Mobile Equipment Identity number (IMEI) of the GSM module.
Note: For details, see the MEITRACK Parameter Editor.
3. Configure the T1, TC68, TC68S, MT90, MVT100, MVT600, MVT800, and T322 by using Meitrack Manager.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 7 -
GPRS: Select TCP.
Protocol: Select Auto Event Report.
IP/Domain:Set the active IP address. The Meitrack server IP address is 67.203.13.26.
Port:Set the TCP or IP port for receiving GPRS data. The Meitrack server port is 8800.
Backup IP/Domain, and Port: This feature is available for users with multiple servers. When the active server fails, device
data will be sent to the standby server automatically. Leave the two options blank if no standby server exists.
APN,APN Username, and APN Password:If the device is used in China, the APN of China Mobile is CMNET, the APN of
China Unicom is UNINET, and no user name and password exists.
GPRS Time Interval:Set the interval for regularly reporting GPRS data. The interval unit is 10 seconds. 6, which indicates 1
minute, is recommended.
GPRS Timezone:Displays the local time when the device communicates with the platform. Leave this option blank if the
MS02 is used. The time zone is set on the MS02.
GPRS Interval (ACC OFF): Set the interval for regularly reporting GPRS data when the engine is disabled. The interval unit
is 10 seconds. To use this feature, the device must be connected to an engine.
Note: For details, see the MEITRACK Parameter Editor.
3.1.2 Configured By Running SMS Commands
1. GT30i, GT60, VT300, VT310, and VT400 commands:
A. Set a command for the tracker (GPRS) ID.
W000000,010,S/N
Check the S/N on the device. The S/N is the unique identification code for the device on MS02. It cannot be changed.
For example, if the S/N is 4037828853, the command is as follows:
W000000,010,4037828853
B. Set a command for the APN.
W000000,011,APN,APN user name,APN password
For example, if a China Mobile phone card is used, the command is as follows:
W000000,011,CMNET
C. Set an IP address and port command.
W000000,012,IP address,port
For example, the command for setting the Meitrack server IP address is as follows:

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 8 -
W000000,012,114.112.54.134,8800
D. Enable the GPRS.
W000000,013,1
E. Set a GPRS interval.
W000000,014,XXXXX
For example, when the tracker sends data to the server once every minute, the command is as follows:
W000000,014,00006
2. MT90, MVT800, MVT100, MVT340, MVT380, MVT600, and T1 commands:
A. Set GPRS parameters.
Command: 0000,A21,Connection mode,IP address,Port,APN,APN user name,APN password
Descriptions:
When the connection mode is 0, the GPRS function is disabled.
When the connection mode is 1, the GPRS function is enabled, and the TCP/IP reporting mode is used.
When the connection mode is 2, the GPRS function is enabled, and the User Datagram Protocol (UDP) reporting
mode is used.
The IP address or domain name has a maximum of 32 bytes.
A port has a maximum of 5 digits.
APN/APN Username/APN Password: An APN, APN user name, and APN password have a maximum of 32 bytes
respectively. If no user name and password is required, leave these parameters blank.
Example: 0000,A21,1,114.112.54.134,8800,CMNET,
B. Set time tracking parameters.
0000,A12,Interval,Number of reporting times
Descriptions:
If the interval is 0, the GPRS regularly-reporting function is disabled. The interval unit is 10 seconds.
The maximum interval is 65535 x 10 seconds.
If the number of reporting times is 0, the GPRS has been reporting (for platform tracking generally). If the number of
reporting times is between 1 and 65535, set the number of reporting times. Reporting will stop after the number
of times is reached.
Example: 0000,A12,6,0
3.2 Logging In to the MS02
Log in to the MS02 in any of the following ways:
Visit ms02.trackingmate.com through your PC.
Obtain a user name and password when you purchase an account.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 9 -
Visit m.ms02.trackingmate.com through your mobile phone.
Obtain a user name and password when you purchase an account.
3.3 Adding a Device
Log in to the system, and choose Manage > Admin.
Click the user name. The following page is displayed:

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 10 -
To add a device, click Add a New Device.
Device ID: The ID is unique.
The GT30, GT60, VT300, VT310, or VT400 ID is the S/N on the device.The MT90, MVT100, MVT340, MVT380, MVT600,
MVT800, or T1 ID is the device IMEI. The SMS query instruction is 0000,E91.
If the device ID is incorrect, device status cannot be queried.
Password: indicates the password for sending SMS commands.
For the GT30i, GT60, VT300, VT310, and VT400, the default password is 000000.
For the MT90, MVT100, MVT340, MVT380, MVT600, MVT800, and T1, the default password is 0000.
If the password is changed, enter the latest one.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 11 -
Device Name: Set the device name, such as a vehicle licence plate, driver name, and company name.
SIM Number: indicates the phone number.
Model: indicates the device model.
3.4 Checking Status Updates
Open the GPS tracking system, choose Status > Updates to check whether the device is added. Ensure that the device is
connected to the server and the GPS tracking is normal.
4Software Functions
4.1 System
4.1.1 Language
Choose System > Language. The MS02 supports 24 languages. The MS02 system language changes according to Window
languages. For example, if the Chinese Windows system is running, the default MS02 system language is Chinese.
4.1.2 Skin
Choose System > Skin. The MS02 supports blue, purple, black, and green. The default colour is blue.
4.1.3 Time Zone
Choose System > Time Zone. The MS02 time zone will be synchronized based on computer system time.
4.1.4 Logout
Choose System > Logout to log out of the system.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 12 -
4.2 Management
4.2.1 Admin
4.2.1.1 Adding a Device
Choose Manage > Admin > Add a New Device.
Note:
Device Limits: The number of newly added devices cannot exceed the limit. The limit is 50 shown in the following figure.
When you want to add more devices, contact the supplier.
Expiry Date: indicates the account expiration date. When the account is about to expire and you want to use the account
continuously, contact the supplier.
For details about how to add a device, see section 3.3.
4.2.1.2 Adding an Existing Device
Choose Manage > Admin > User Name > Add Existing Device.
Multiple accounts can be used to monitor the same device.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 13 -
Device ID: The ID is unique.
The GT30, GT60, VT300, VT310, or VT400 ID is the S/N on the device. The MT90, MVT100, MVT340, MVT380, MVT600,
MVT800, or T1 ID is the device IMEI.
The parameter must be consistent with the device ID you added the first time.
SIM Number: indicates the phone number. The parameter must be consistent with the device ID you added the first time.
Password: indicates the password for sending SMS commands. For the GT30, GT60, VT300, VT310, and VT400, the default
password is 000000. For the MT90, MVT100, MVT340, MVT380, MVT600, MVT800, and T1, the default password is 0000.
If the password is changed, enter the latest one.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 14 -
4.2.1.3 Removing a Device
Device ID: Enter the S/N or IMEI when you add the device.
Password: indicates the password for sending SMS commands.
For the GT30i, GT60, VT300, VT310, and VT400, the default password is 000000.
For the MT90, MVT100, MVT340, MVT380, MVT600, T1, MT90, and MVT800, the default password is 0000.
If any of these parameters is entered incorrectly, the device cannot be removed.
4.2.2 Tracker Customization
Choose Manage > Tracker customer define to customize alarms, I/O status, and the connected sensor formula. The function is
only available for devices bounded to the MS02.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 15 -
4.2.2.1 Customizing an Alarm
Define status changes (activity or inactivity) of input ports. When the status changes, the device sends GPRS data to the server.
For example, when you define SOS Pressed as SOS, the SOS button is pressed, the SOS alarm will be sent to the system. When
you define Input 4 Active as ACC ON, input port 4 is active and the engine is on. When you define Input 4 Inactive as ACC OFF,
input port 4 is inactive and the engine is off.
To customize an alarm, click , specify parameters shown in the following figure, and click Add.
For example, select a device, and set Alarm Type to SOS Pressed and Name to SOS. When the customized alarm triggers,
device status will be displayed on a map, as shown in the following figure.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 16 -
4.2.2.2 Customizing Status
Define I/O port status. The status information is in data packages sent to the server.
Output 1 connects the engine circuit to a relay. When the circuit is cut off (output activated), cut is defined. If the circuit is
connected (output inactivated), normal is defined.
To customize status, click , specify parameters shown in the following figure, and click Add.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 17 -
4.2.2.3 Customize a Sensor
Customize sensor formulas. The function applies for linear analogy sensors, such as fuel sensors. After formulas are customized,
formulas will be displayed in the system.
To customize a sensor, click , specify parameters shown in the following figure, and click Add.
4.2.3 Customizing a Temperature Sensor
The function is only available for the MVT600, T1, and MVT800.
A temperature sensor is used to measure temperature of vehicles and environments in real time.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 18 -
For details, see the MEITRACK Temperature Sensor User Guide.
4.2.4 Setting a Fuel Sensor
The function is only available for the MVT600, T1, and MVT800.
A fuel sensor is used to measure vehicle fuel and check whether an alarm is generated.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 19 -
For details, see the MEITRACK Fuel Sensor User Guide.
4.2.5 Setting a LED
The function is only available for the MVT600, and T1.
An LED is used to issue vehicle advertisements and emergent notices.

MEITRACK MS02 User Guide
Copyright © 2014 Meitrack Group All rights reserved. - 20 -
For details, see the MEITRACK LED User Guide.
4.2.6 Setting Parameters
The function is only available for the MVT100 and TC68S.
Set parameters for an online device.