Members Mark Livingston SMWD-2 Owner's manual

Need Assistance? Visit us at: samsclub.com/membersmarkhelp 1 | P a g e
Assembly Instructions & User’s Manual
for
Livingston Writing Desk
Model Number: SMWD-2 / SMWD-2-E
Customer Assistance (spare/replacement parts): 1-866-942-5362
or Email: [email protected]
THIS ASSEMBLY MANUAL CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Need Assistance? Visit us at: samsclub.com/membersmarkhelp 2 | P a g e
Table of Contents
Quality Statement ..................................................................................................................................... 3
Important Safety Information ................................................................................................................ 3
Before Assembly ...................................................................................................................................... 3
Care & Use ................................................................................................................................................. 3
Furniture Power Distribution Center Important Safety Instructions ........................................................ 4
Furniture Power Distribution Unit User Guide ......................................................................................... 5
Package Contents .................................................................................................................................... 6
Product Information ................................................................................................................................ 6
Components .............................................................................................................................................. 7
Hardware .................................................................................................................................................... 7
Tools ............................................................................................................................................................ 7
Step 1 .......................................................................................................................................................... 8
Step 2 .......................................................................................................................................................... 9
Step 3 ........................................................................................................................................................ 10
Step 4 ........................................................................................................................................................ 11
Warning ....................................................................................................................................... 12
Troubleshooting ..................................................................................................................................... 13
Care & Use Instructions ....................................................................................................................... 13
Warranty Information ............................................................................................................................ 13

Need Assistance? Visit us at: samsclub.com/membersmarkhelp 3 | P a g e
Quality Statement
Important Safety Information
 Please read all instructions carefully before assembling this product.
 Where applicable, and for your safety, assembly by an adult is strongly recommended.
 Use only vendor-supplied hardware to assemble this item. Using unauthorized
hardware could jeopardize the structural integrity of the item.
 Hardware may loosen overtime. Periodically check that all connections are tight.
Before Assembly
 Remove all parts and hardware from the box. Place all items on a carpeted or
scratch-free work surface, as this will avoid damaging parts during assembly.
 The shipping box can provide an ideal work surface if none is available.
 Use the components and hardware lists below to identify, inventory and separate
each of the hardware and components included.
 To avoid accidentally discarding small components or hardware, do not dispose of
any packaging or contents of the shipping carton until assembly is complete.
 DO NOT USE power tools unless it is explicitly identified in this manual as required
for use during assembly. Power tools can damage the fasteners, hardware and/or
components.
 Do not fully tighten all fasteners / screws until all parts are in place. Failure to follow
these instructions may cause the fasteners / screws to misalign during assembly.
Care & Use
 Use a soft, clean cloth that will not scratch the surface when dusting.
 Use of furniture polish is not necessary. Should you choose to use polish, test first in
an inconspicuous area.
 Using solvents of any kind on your furniture may damage the finish.
 Never use water to clean your furniture as it may cause damage to the finish.
 Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill
gently. Avoid rubbing.
 Do not place furniture in direct sunlight.

Need Assistance? Visit us at: samsclub.com/membersmarkhelp 4 | P a g e
FURNITURE POWER DISTRIBUTION CENTER
IMPORTANT SAFETY INSTRUCTIONS
Carefully read all instructions installing and operating fixture
IF YOU HAVE ANY QUESTIONS REGARDING THE PROPER
INSTALLATION CONSULT A QUALIFIED ELECTRICIAN.
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK OR INJURY TO PERSONS, PLEASE FOLLOW THE NEXT:
 Use only insulated staples or plastic ties (not included) to secure the cords.
 Route and secure cords so that they will not be pinched or damaged when the
desk is pushed up against the wall.
 Make sure cord is not pinched between desk and floor.
 Use the unit indoors only.
 Do not use an extension cord to connect this unit to a wall outlet.
 Use power strip with integral over-current protection to supply other electrical
devices or accessories in desk.
 This unit must be plugged into a properly grounded outlet.
 The socket outlet should be installed near the equipment and should be easily
accessible.
 Maximum load of connected equipment cannot exceed a total of 12 amps and
120 volts.
 Do not open or disassemble this unit for any reason.
SAVE THESE INSTRUCTIONS

Need Assistance? Visit us at: samsclub.com/membersmarkhelp 5 | P a g e
Furniture Power Distribution Unit User Guide
Please read this user guide before installing and using your power distribution Center.
INTRODUCTION
The integrated power and USB center can
connect up to three devices, such as a digital
camera, MP3 player or cell phone.
SPECIFICATIONS
cULus listed, rated for: 120 V ac, 12 A, 60 Hz
NOTES
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment
and receiver.
 Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
 Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
This Class B digital apparatus complies with
Canadian ICES-003.
Whalen Furniture Manufacturing
1578 Air Wing Road,
San Diego, CA 92154, USA
1-866-942-5362
WARNINGS
! Your hub automatically shuts off any port with
a low or excessive current.
! If USB Hub Current Limit Exceeded appears
on your screen, disconnect the affected USB
device, click Reset on the screen, and
reconnect the device.
! If one of your hub ports is disabled, but USB
Hub Current Limit Exceeded does not
appear:
 Disconnect and reconnect the affected
device.
 If the port still does not work, disconnect the
hub and the device, and then reconnect.
! Keep your desktop hub dry; if it gets wet, wipe
it dry immediately.
! Do not modify or tamper with your desktop
hub’s internal components. It may cause a
malfunction and invalidate its warranty.
! Modifications not approved by the party
responsible for compliance could void user’s
authority to operate the equipment.
Product:
Furniture Power Distribution Unit
Model No: HG2000-DBU2
Company:
Whalen Furniture Manufacturing

Need Assistance? Visit us at: samsclub.com/membersmarkhelp 6 | P a g e
Package Contents
Component Description Quantity Component Description Quantity
A Desk Top 1 C Right Side Frame 1
B Left Side Frame 1 D Bottom Stretcher 1
Product Information
Dimensions – 47.5” x 23.5” x 30.25” (120.6cm x 59.7cm x 76.8cm)
Weight Capacity
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
A
B
C
D
MAXIMUM LOAD 90.7 kg / 200
lb

Need Assistance? Visit us at: samsclub.com/membersmarkhelp 7 | P a g e
Components
Component A
Part No. 00SMWD-2-A
Qty 1
Component B
Part No. 00SMWD-2-B
Qty 1
Component C
Part No. 00SMWD-2-C
Qty 1
Component D
Part No. 00SMWD-2-D
Qty 1
Hardware
1/4 x 1 1/2” Bolt (H1)
Part No. 00SMWD-2-E
Qty: 10+1 extra
Lock Washer (H2)
Part No. 00SMWD-2-F
Qty: 10+1 extra
Flat Washer (H3)
Part No. 00SMWD-2-G
Qty: 10+1 extra
M4 x 50 mm Screw (H4)
Part No. 00SMWD-2-H
Qty: 2+1 extra
M3 x 12 mm Screw (H5)
Part No. 00SMWD-2-I
Qty: 6+1 extra
Cord Clip (H6)
Part No. 00CC001
Qty: 3
Touch-up Pen (H7)
Part No. 00SMWD-2-K
Qty: 1
Tools
Phillips Screwdriver (Not Included) Hex Wrench (H8) (Included)
Part No. 00SMWD-2-L
Qty: 1

Need Assistance? Visit us at: samsclub.com/membersmarkhelp 8 | P a g e
H1 x 5 H2 x 5 H3 x 5
Step 1
NOTE: Please do not fully tighten all bolts/screws until you finish assembling all parts.
Once assembled, go back and fully tighten all bolts. This will make it easier during
assembly of unit.
a) Unpack the units and confirm that you have all hardware and required parts.
b) Attach Right Side Frame (C) to the Desk Top (A) with five 1 1/2” Bolts (H1), five Lock
Washers (H2) and five Flat Washers (H3). DO NOT over-tighten the bolts.
A
C
The mortise faces inward
and is located at back.

Need Assistance? Visit us at: samsclub.com/membersmarkhelp 9 | P a g e
Step 2
a) Orient and insert the tenon of the Bottom Stretcher (D) into the mortise of the Right
Side Frame (C). Make sure the slant holes on the Bottom Stretcher will face the floor
when the unit is turned upright.
b) Align and attach the Left Side Frame (B) to the Desk Top (A) while inserting the tenon
of the Bottom Stretcher (D) into the mortise on the Left Side Frame (B).
C
D
B
A
Slant holes

Need Assistance? Visit us at: samsclub.com/membersmarkhelp 10 | P a g e
H1 x 5 H2 x 5 H3 x 5
H4 x 2
Step 3
a) Insert five 1 1/2” Bolts (H1) with the Washers (H2 and H3) through the mounting holes
on the top rail of the Left Side Frame (B) and screw into the Desk Top (A).
b) Insert and screw two 50 mm Screws (H4) into the slant holes in the Bottom Stretcher
(D). Tighten the screws with a Phillip screwdriver.
A
C
D
B