Members Mark Hastings AAX08800-9SC Owner's manual

THIS ASSEMBLY MANUAL CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Assembly Instructions & User's Manual
for
Members Mark Hastings 9PC Regular Dining Set
Item Number:
Model Number: AAX08800-9SC
Customer Assistance : 1-800-416-3511
or Email: [email protected]
(spare/replacement parts)
Page 1
Need Assistance? Visit us at: samsclub.com/membersmarkhelp

Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 2
Table of Contents
Quality Statement.............................................................3
Important Safety Information.............................................3
Before Assembly..............................................................3
Package Contents............................................................4
Product Information..........................................................5
Care & Use and Storage Instructions.................................12
Warranty Information.......................................................12
Swivel Rocker
Components................................................................6
Hardware....................................................................6
Tools..........................................................................6
Step1.........................................................................7
Components...............................................................8
Hardware...................................................................8
Tools..........................................................................8
Step1-Step5..........................................................9-11
Table

Before Assembly
Important Safety Information
Please read all instructions carefully before assembling this furniture.
For your safety, assembly by two or more adults is strongly recommended.
Use only vendor-supplied hardware to assemble this item. Using unauthorized
hardware could jeopardize the structural integrity of the item.
Hardware may loosen overtime. Periodically check that all connections are tight.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 3
Quality Statement
Remove all parts and hardware from the box. Place all items on a carpeted or
scratch-free work surface, as this will avoid damaging parts during assembly.
The shipping box can provide an ideal work surface if none is available.
Use the components and hardware lists below to identify, inventory and
separate each of the hardware and components included.
To avoid accidentally discarding small components or hardware, do not dispose
of any packaging or contents of the shipping carton until assembly is complete.
DO NOT USE power tools unless it is explicitly identified in this manual as
required for use during assembly. Power tools can damage the fasteners,
hardware and/or components.
Do not fully tighten all fasteners / screws until all parts are in place. Failure to
follow these instructions may cause the fasteners / screws to misalign during
assembly.

Need Assistance? Visit us at: samsclub.com/membersmarkhelp
1Set / 2Ctn
Box1of2：
Box2of2：
Component Quantity
Description
A
B
C
6
2
Component QuantityDescription
A1
A B
Page 4
Package Contents
A
Dining Table
1
C
Dining Chair
Swivel Rocker
Furniture Cover

Description Dimensions
Part No.
AAX08800 Y
A.Foot Cap
N/A N/A Y
A
FC0607
Dining Chair
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 5
Product information
Description Dimensions
Part No.
AAX08801 25.5" W *24.25" D *34.5" H 250lb per seat N
A.Foot Cap
FC0175 N/A N/A Y
A
Swivel Rocker
Description Dimensions
Part No.
ALX24215
41.75" W *85.5" D *29.5" H
(Full extended size: 41.75" W
*107.75" D *29.5" H)
Weight
Capacity
Factory
Assembly
N
A.Foot Cap FC0030 N/A N/A Y
Dining Table
A
N/A
25.5" W *24.25" D *34.5" H 250lb per seat
Weight
Capacity
Factory
Assembly
Weight
Capacity
Factory
Assembly
Description Part No.
ZZK03012
Furniture Cover

(H1)
5/16"X40MMBOLT
Qty: 4
PART NO:HW0806
(H2)
Qty: 4
Ø8.0 X 2.3 MM SPRING WASHER
PART NO:HW0003
(H3)
Qty: 2
"U" METAL PLATE
PART NO:HW0618
(H4)
Qty:
5/16" NUT
PART NO:HW0015
4
(H5)
Qty:
ROCKER PLATE
(
G0228
FACTORY ASSEMBLY)
PART NO:
2
Components
Hardware
A.
Part No.AR20323
Qty 1
CHAIR FRAME
Tools
Page 6
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
(H7)
HEX WRENCH-2
HW0008
Qty:
PART NO:
1
(H6)
HEX WRENCH-1
HW000
Qty:
PART NO:
1
7
B.
Part No.AR20324
Qty 1
SWIVEL BASE & ROCKER
ASSEMBLY

"U" BAR
(H3)
U" METAL PLATE
Qty: 2
(H7)
HEX WRENCH-2
Qty: 1
(H6)
HEX WRENCH-1
Qty: 1
(H4)
5/16" NUT
Qty: 4
(H2)
Ø8.0 X 2.3 MM SPRING WASHER
Qty: 4
(H1)
5/16"X40MMBOLT
Qty: 4
"U" BAR
"U" BAR
H3
H4
H2
H1
Hand tighten only 2-3 turns.
NOTE: Bolts must be
FULLY .tightened
AB
CD
E
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 7
Step 1
H6
H7
CAUTION:
1.Note the horseshoe shape of the rocker plate. Point the open end of the horseshoe away from you. The arrows
on the rocker assembly should be pointing towards you.
2.Failure to place "U" metal plates (H3) under the rocker plates and above the "U" bar exactly as shown in
diagram will cause the bolt heads and nuts to damage the structure of the rocker plates and the "U" bar. Damage
due to over tightening of bolts or improper assembly could cause injury and may void your warranty.

Components
A.
Part No.
Qty 1
TABLE TOP
AT73200
B
Part No.
Qty 1
.LEG CONNECTOR
BRACKET-1
AT73201
C.
Part No.
Qty 1
LEG CONNECTOR
BRACKET-2
AT73202
Tools
(H5)
HEX BOLT DRIVER
Qty:
PART NO:HW0006
1
Page 8
D.
Part No.AT3203
Qty 4
TABLE LEG
(H6)
Qty: 1
HEX WRENCH
HW0009
PART NO:
(H1)
1/4"X20MMBOLT
Qty: 8
PART NO:HW0802
(H2)
Qty: 24
Ø6.5 X 1.0 MM WASHER
PART NO:HW0004
(H4)
Qty:
(FACTORY ASSEMBLY)
UMBRELLA HOLE RING (SET)
PART NO:G0235 & G0236
1
(H3)
Qty: 16
1/4" NUT
PART NO:HW0014
Hardware

outer carton
Hand tighten only 2-3 turns.
H2
H3
Hand tighten only 2-3 turns.
H1
H3
Step 1
Step 2
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Step1-Step4
Page 9
(H1)
1/4"X20MMBOLT
Qty: 8
(H2)
Qty:
Ø6.5 X 1.0 MM WASHER
8
(H2)
Qty: 16
Ø6.5 X 1.0 MM WASHER
(H3)
1/4" NUT
Qty: 16

4x
4x
H5
H6
Step 3
Step 4
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 10
(H5)
Qty: 1
HEX BOLT DRIVER
(H6)
Qty: 1
HEX WRENCH
4x
CAUTION: Please read the instruction in step 5 carefully before you extend the table top to full size.

Retracting Extended Table Top
Step 2
Step 1
Notice: pull the end sections to half or two
thirds of extended length until the center
section starts to go down.
unlock
Step 3
Push back
Step 4
lock
Step 1
How to Extend Table Top
Step 3
Push back after extended to close gap.
Step 4
lock
locked unlocked
Warning: Please make sure the top
is locked before use
unlock
Pull apart to fully extend.
Step 2
Page 6
Step 5
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 11

CARE AND MAINTENANCE
FRAMES
FABRICS
STRAPS
UMBRELLA USAGE WARNING!
Cleaning
Maintenance
Cleaning -
Maintenance
Cleaning -
Maintenance -
- Use mild soap and warm water. Do not use abrasive materials, cleansers or bleach
products. Rinse with clean water and dry thoroughly.
- Periodically clean and dry thoroughly. Be sure to drain any water accumulated inside the
frames. To thoroughly drain frames, remove foot caps and tilt the frames, if necessary, to remove all
water. This is critical. Water allowed to accumulate inside the frames and then exposed to sub-freezing
temperatures can cause damage to the frame tubing. Always clean, drain and dry thoroughly before
storing for the winter. For best results, always store or cover your furniture when not in use. We
recommend commercially available outdoor furniture covers. Any small nicks or scratches can be
covered with a light application of touch-up paint.
** When cleaning or moving large or heavy items, always have two people work together. Never drag
furniture.
Wipe minor spills immediately. Clean with mild soap, warm clean water and soft cloth. Do
not use abrasive materials, cleansers or bleach products. Although fabric has been treated to resist
stains, occasional use of commercially available fabric cleaners may be necessary. Follow
manufacturer's instructions.
- The best way to maintain the beauty of cushions and slings is to store them in a dry area
and out of the elements when not in use or cover with commercially available outdoor furniture covers.
Furniture covers are a great way to protect your set from harsh elements of weather and UV light.
However, it is important to ensure furniture and covers are free of moisture and debris before covering.
It is also necessary to promptly uncover furniture after rain and during periods of high humidity to
prevent moisture build up. Failure to do so can lead to permanent surface and finish damage.
Wash frequently with mild soap, warm water and a soft cloth. Rinse thoroughly with warm,
clean water. Do not use abrasive materials, cleansers or bleach products.
Periodic application of commercially available vinyl cleaners and vinyl protectors will
enhance the look and prolong the life of straps. If your strap chair has cushions, make sure any vinyl
protectors applied are completely dry before placing cushion back on the chair.
If you will be using an umbrella with your table, make sure the plastic umbrella ring is inserted into the
hole in the center of the table. Place the umbrella through the opening and into an umbrella stand
made of cast iron, wrought iron, steel plate or blow molded plastic filled with 20-50 lbs or 9-22 kgs of
sand and water. If your table is 72" or 182 cm or larger, we recommend a weight of at least 50 lbs or 22
kgs or more. NEVER USE AN UMBRELLA WITH A TABLE WITHOUT USING AN UMBRELLA BASE
AND RING AS DESCRIBED ABOVE. ALWAYS REMOVE YOUR UMBRELLA FROM THE TABLE
WHEN NOT IN USE. NEVER USE AN UMBRELLA DURING STORMS OR WINDY CONDITIONS.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Care & Use Instructions
Warranty Information
This product component has a 5 year guarantee against defects in material and/or workmanship. If
you have any questions regarding the warranty or spare / replacement parts, please call our toll-
free number 1-800-416-3511 or email us at [email protected]
NOTE: Please consider recycling all applicable packaging material.
Page 12

Distributed by Sam's West Inc.
2101 SE Simple Savings Dr.
Bentonville, Arkansas 72716-0745
Made in China
Page 13
Need Assistance? Visit us at: samsclub.com/membersmarkhelp