Mercia Garden Products 01JER0806-V1 User manual

01JER0806-V1
Dimensions
Depth = 182cm
Width = 244cm
Height = 225cm
For Assistance Please
Contact Customer Care on
01636 880514
2mm Drill bit
x2
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
This building should be erected by
two people.
For ease of assembly, it is advisable to
pilot drill all screw holes and ensure
all screw heads are countersunk.
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are delivered pre-treated with a water based timber treatment
however this only helps to protect during transit of your garden item. To
validate your guarantee and for better protection against weathering it is
ESSENTIAL that you treat the garden building with a wood preserver within 3
months of assembly. This will need to be re-applied annually to ensure longevity
of your building. Care must be taken when constructing the garden building
that it is not touching the ground and is on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed: Ensure that there will be access to all sides for maintenance work and
annual treatment.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be slightly
smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run o for water. It is also recommended
that the oor be at least 25mm above the surrounding ground level to avoid ooding.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products independently tested to EN71 level, we
cannot accept responsibility for your safety whilst erecting or using this product.
Before
assembly make sure you
have a suitable base
ready to erect your
building
Please retain product label and instructions for future reference
4x Front Fascia- 95 x1460mm
Fixing Kit
Floor Plain Gable Plain Side x2
Door Gable Roof Panel Left Roof Panel Right
4x Corner strips- 30 x 1652mm
2x Finial
4x Fascia block
123
456
8
9
11
12
7
Door Panel
10 x2 Beading strips- 30 x 1662mm
2x Window Strip
2x Window Strip
2x Window
casement stay x2
Turn
button x2
Pad bolt
50mm Screw x 22
40mm Screw x 40
30mm Screw x 60
30mm Black Screw x 19
Felt
Felt Tacks x 100
20mm Screw x 15
13 14
15
16
17
Hinge x3
16mm Screw x 16
18
19
20
Hinge x4

Before assembly fix the hinges
to the door gable using
7x30mm screws for each one.
Pre Assembly
21x30mm Screws
Before assembly fix each
Beading Strip to the door
gable using 4x30mm screws
for each one.
8x30mm Screws
Pre Assembly
10
7
19
Lay the door gable down on a at surface
before tting the window strip and window.
30mm
screw
Place the opening window strip
11mm above the window gap in the
window panel and fix with 3x30mm
screws.
3x30mm Screws
*SCREW COUNT PER WINDOW
30mm
16mm
30mm
screw
16mm
screw
If you would like the windows to be
opening use the butt hinges to
attach the opening window strip
and the opening window together.
Use 30mm screws to fix the butt
hinge to the Window Strip and
16mm screws to fix it to the
Opening Window.
8x30mm Black Screws
8x16mm Black Screws
13
20
14

Remove transportation blocks
from the bottom of each panel
before beginning assembly.
Each Panel should have two
blocks.
Step 1
Place floor on a firm and level
base, ensure base has suitable
drainage free from areas
where standing water can
collect. (See front page on
base requirements).
Step 2
1
Do not secure the building
to the floor until the roof is
fitted. Fix the panels onto
the floor using 50mm
screws in alignment with
the floor joists.
Fix the corner with 3x
50mm screw a shown in
diagram.
Step 3
11 x 50mm screws
50mm
screw 2
3
Step 4
Fix door gable and remaining
plain side using the same method
shown in step 4.
9 x 50mm screws
50mm
screw
3
4

BUILDING A BASE
When thinking about where the building and base is going to be constructed: Ensure that there will be access to all sides for maintenance work and
annual treatment.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be slightly
smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run o for water. It is also recommended
that the oor be at least 25mm above the surrounding ground level to avoid ooding.
Place Roof panels into position on top
of building using the slot at the top as
a guide. Ensure the overhang is at the
front and that the center roof purlin
fits inbetween the front and rear
gable.
Secure each panels with 10x40mm
screws per panel.
20 x 40mm screws
Place a facia block at the front and
back of each roof panel. Secure using
2x40mm screw per block.
40mm
screw
8 x 40mm screws
40mm
screw
Step 5
5
6
Step 6
Cut four equal strips from roll of felt,
making sure they cover the length of
the roof with 50mm overhang on
each end.
Lay on roof in the order shown in
diagram and secure using felt tacks
with 100mm spacing between each.
12
Step 7
100 x Felt tacks
Felt
Tacks 17
Step 8
Fix fascias to front and back
using 40mm screws into the
roof framing and fascia
block.
Then fix the finials at the top
of apex, overlaping both
fascias with a 40mm screw.
10 x 40mm screws
40mm
screw
8
11

Fix casment stays to the
opening window then align
the fixings onto the the
window panel frame. ensure
the casement stay fits into
fixings when closed before
screwing them down using
20mm screws.
6x20mm screws per casement stay
Step 8 Step 9
20mm
screw
Fix corner strips using 3 x 30mm screws per strips.
30mm
screw
12 x 30mm screws
9
18

10 x 30mm screws
2 x 30mm black screws
30mm
black
screw
I
t
i
s
E
S
S
E
N
T
I
A
L
t
h
a
t
y
o
u
a
p
p
l
y
w
o
o
d
t
r
e
a
t
m
e
n
t
i
m
m
e
d
i
a
t
e
l
y
a
f
t
e
r
t
h
e
b
u
i
l
d
i
n
g
h
a
s
b
e
e
n
a
s
s
e
m
b
l
e
d
.
Fix Pad Bolt with 6x 30mm
Screws to horizontal brace
to the door.
Then x the pad bolt
retainer to the door gable
framing using 4x30mm
Screws
Fix the two turn buttons to
the door panel at the top
and bottom of the door
using the 30mm back
screws.
30mm
screw
Step 10
16
15