Mercia Garden Products 04GREEN0406SD-V6 Instruction manual

**Protim Aquatan T5 (621)**
Your building has been dip treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
Measure
under the
head
Measure
overall
length
Screws & Nails Bolts To identify the
xings required
for each step use a
measuring tape.
04GREEN0406SD-V6
4x6 Greenhouse
2mm Drill bit
x2 Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All buildings should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-
driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
LOCATION FOR YOUR GARDEN BUILDING
A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,
annual treatment and to allow air ow around the building.
Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing
damage to the building.
TIMBER
As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy
or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during
excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be
helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine
and sheltered as much as possible during rain or snow.
Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent
the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.
Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-
ment to prevent water ingress
Pressure Treated buildings - Require a waterproof treatment to prevent water ingress
Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base
dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding
should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above
the surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or
using this product.
For ease of assembly, you
will need a tape measure to
check dimensions of
components.
P 1
Please retain product label and instructions for future reference
General Instructions
REGISTER FOR YOUR
ANTI-ROT
GUARANTEE TODAY
PLEASE SCAN HERE:

P 2
04GREEN0406SD-V6
Overall Dimensions:
Width = 1215mm
Depth = 1887mm
Height = 2066mm
Base Dimensions:
Width =1191mm
Depth = 1862mm
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Door Side
AI-04GREENDS610X1543-V5
QTY 2
Sml Window Side
AI-04GREENWS1193X1543-V5
QTY 2
Lrg Window Side
AI-04GREENWS1776X1543-V5
Door Gable Top
AI-04GREENDGT1864X426-V5
Roof
(Opening Window)
AI-04GREENROOFOW1218X1037-V1
Plain Gable Top
AI-04GREENPGT1864X426-V5
23
45
1
6
Roof
AI-04GREENROOF1218X1037-V1
8
Door
AI-04GREENDOOR550X1720-V5
9
Opening
Window
AI-04GREENOW560X460-V5
789
10
11
Fascia - 12x56x1075mm QTY 4
Base Frame - 44x44x1864mm QTY 2
Base Frame - 44x44x1105mm QTY 2
10
11
12
13
Roof Support Bar 27x44x1242mm QTY 1
18 19
F4444-1105mm
S1256-1075mm
F4444-1864mm
F2744-1242mm (8mm LIP, X2 66DEG CUTS)
S1227-556mm
S1227-1717mm
S1256-1242mm
F2744-556mm
PI-07-0004 PI-07-0008
PI-07-0182
Buttery Hinges QTY 4 Window Casement Stay Window Glazing Bead QTY 8
PI-07-0063
20
Finial QTY 2
21 22
Wooden Knob
23
Turn Button QTY 2
15
16
Door strip - 12x27x1717mm QTY 2
Roof trim - 12x56x1242mm QTY 1
17
Short Door strip - 12x27x556mm QTY 1
Door Frame - 27x44x556mm QTY 1
13
14
PI-04-0024SHED DIAMOND FINIAL

P 3
Please retain product label and instructions for future reference
Window Strip - 12x27x1776mm
Window Strip - 12x27x926mm QTY 14
S1227-926mm
Window Cill 610mm QTY 2
Window Cill 1193mm QTY 2
Window Cill 1776mm
PI-08-0021
PI-08-0019
PI-08-0020
S1227-1776mm
Window Strip -12x27x1193mm QTY 2
Window Strip - 12x27x610mm QTY 2
S1227-1193mm
S1227- 610mm
Strip - 12x44x543mm
S1244- 543mm
Strip - 12x21x560mm
S1221- 560mm
Corner Trims - 12x56x1576mm QTY 4
S1256- 1576mm
Strip - 12x44x993mm QTY 6
Styrene 942x570x2mm QTY 9
Styrene 503x570mm
Styrene 985x570mm QTY 3
PI-05-0151
PI-05-0157
PI-05-0158
S1244- 993mm
Strip - 12x44x1218mm QTY 2
S1244- 1218mm
28
27
26
25
24
29
33
34
35
36
37
38
30
31
32
Nail Bag 30mm Screw x 150
20mm Screw x 6
50mm Screw x 70
70mm Screw x 8
40mm Screw x 8
16mm Screws x 20
30mm Black Screw x 18

Side
Rear
Front
P4
Please retain product label and instructions for future reference
Step 1
Lay the base frame down as shown in the
diagram. Ensure the base is square and
layed on level ground. Fix the base
framing (No. 11)&(No. 12)together with
2 x 70mm screws per corner, pre drill to
avoid splitting the timber.
8x70mm screws.
Pre drill
hole
70mm
screw
Pre drill
hole
Step 2
Assemble the window panels on the oor.
Place the plastic window cill onto the lip
of the window panel externally.
1b. Lay the styrene on top of each open-
ing so that it overlaps the surrounding
framing equally on both sides as per the
diagram.
Step 3
Attach the window strips using 3x30mm
screws as per the diagram, starting with
the top strip. Ensure the framing does not
protrude the width of the window frame.
Ensure you screw into the window strips
to the side of where the styrene meets
the window frame.
81x30mm
11
11
12
12
Styrene
Styrene
Styrene
Window Cill
Styrene
24
24
24
25
27
26
Styrene
Styrene Styrene
Styrene Styrene Styrene
34
35
36
30
30mm
screw
Pre Assembly
Before assembling remove the transportation
blocks from the bottom of each panel.

P 5
Please retain product label and instructions for future reference
Step 4
Fix the corners of the Sml Window Side
(No. 2) and the Lrg Window Side (No. 3)
with 3x50mm screws as shown in the
diagram.
*The large window side sits inbetween
the two side panels.*
3x50mm screws.
Pre drill
hole
50mm
screw
Side
Front
Rear
Step 5
Fix the remaining Sml Window Side
(No. 2)at the corner using 3 x 50mm
screws.
3x50mm screws.
Pre drill
hole
50mm
screw
Side
Front
Rear
Step 6
Fix the Door Sides (No. 1)between the
window panels using 6x50mm screws.
6x50mm Screws.
Pre drill
hole
50mm
screw
Step 7
Fix the Door frame (No. 14) to the base
frame between the Door sides. This
allows for the door sides to be correctly
spaced.
3x40mm Screws.
Pre drill
hole
50mm
screw
32
2
1
1
14
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk