MERLYN 6 Series User manual

Thank you for choosing Merlyn.Please familiarise yourself
with the fitting instructions before commencing fitting.
1. Check that you have the tools required.
2 that the installation site is compatible . Check
with size of door supplied
3. Check all the enclosure components.
4 that the installation kit is complete. Check
DO NOT attempt to install the product unless you can
tick ALL 4 boxes as satisfactory.
The wall plugs supplied with the installation kit are for
use in solid walls. Hollow or 'stud-partition’ walls will
require alternative fixings. Please consult a hardware
supplier for the correct type.
It may also be necessary to consult your tiling supplier
about the correct method for drilling your tiles.
VIVID
10
IMPORTANT
Any parts missing or damaged must be reported to your supplier within 5 days of purchase.
Inspect shower enclosure before fitting. No claims will be acceptable after product has been installed.
.
USE SAFETY EYEWEAR WHEN DRILLING
INSTALLATION GUIDE
OFFSET QUADRANT
M037-00

COMPONENTS AND BOX CONTENTS 1
Note: Further part details for fixing kit available on page 2
6
9
1 0
1 1
1 2
1 4
1 5 1 7
3
2
1
1 6
4
8
1 8
5
1 3
1 92 02 12 22 3
Rail
Bottom roller
Screw cover cap
Upright water seal for straight fixed panel
Cover cap for wall profile
∅6 30 wall plug×
Screw cover cap clip
Wall profile
Cover profilecap for upright L/R
6
5
2
9
8
7
10
11
12
13
14
15
1
3
DescriptionNo. QTY Description QTY Part No. No. Part No.
2
2
6
12
6
1
2
2
1
4
1
2
1
B head screw ST4 30×
14
4
Flat head screw ST4 12×
12
V4111
V4110
V6113
V2114
V2115
S6HDLE
Flat fixed panel
Handle
Moving panel
1
16
17
18 Fixed panel
19
Roller cover cap
20
1
1
4
4
A
B
D
21
4
22
Glass clip screw
4
Fixed panel seal
Glass clip
7
Upright water seal for moving panel
Upright water seal for fixed panel
Roller stop
Glass clip screw
23
24
2 4
Top roller
V4101
V3211
8
2
S6LC8431
S6S01
V2101L/R
V2104 C
V6105
V2109
V6106L/R
S6LC83291871
S6LC83291805
V4109
S6LL8060
S6LL8059

FIXING KIT COMPONENTS, TOOLS REQUIRED, SITE 2
V2115
12×
V2114
12×
V6113
×6
V6115
× 1
Tools Required
- 6mm masonry drill bit
- Power drill
- Quality Silicone
- Pencil
- Tape Measure
- #2 Philips Head screw driver
- Spirit level with horizontal and vertical level indicators
IMPORTANT - Installation site
1. Ensure the top surface of the shower tray on which the enclosure will be installed is level in every direction.
2. The tiles or other wall finishing should be effectively sealed at the tray edges.
3. Tiles should extend at least to the corners of the tray and a minimum of 2.0 metres from the top of the tray.
Spanner
-
V2101L
1×
V2101R
1×
V2104
×2
S6HDLE
1×
S6HDLEP2 1×
S6HDLEP3 2×
S6HDLEP4 2×
S6HDLEP1 1×
S6HDLEP6 2×
S6HDLEP7 1×
S6HDLEP5 4×
V4111
×14
V4110
×6
S6LL8059
2×
S6LL8060
2×

FITTING WALL PROFILE 3
PROCEDURE
TRAY MUST BE 100% LEVEL IN ALL DIRECTIONS
Ensure the shower tray is level in all directions and is
properly sealed to the wall. The wall must be tiled down to
the top edge of the tray. Do not angle out bottom tile.
TRAY MUST BE SEALED FULLY AROUND WHERE THE
TRAY MEETS THE WALL.
100％ level
Step 1.
Step in wall profile 20mm from the front edge of the shower tray. Ensure wall profile is plumb.
Do not silicone behind wall profile to wall, see sealing section.
Step 2.
Mark the position for fixing the wall profile to wall.
20mm
2
V6113
Inside
∅6mm
drill bit
masonry
V4111
V2114
20mm
Inside
100％ level
S6S01

FITTING RAILS 4
Step 3.
Loosen fixed glass
panel clips.
Do not remove the
screw.
3
Step 4.
Place fixed panel gasket onto bottom edge of glass.
Then fix the two fixed panels and upright profiles to
the bottom rail, using V4111 screw.
V4111
4
Step 5.
Fit the wall profiles to the assembled
frame.
Step 6.
Tighten fixed glass
panel clips.
6
V4111
5
V3211 U shape seal
(flush with glass
edge)
V3211 U shape
seal (flush with
glass edge)

5
Moving panel
Outside
Step 7.
Position the assembled frame onto the
tray and slide over the wall profile.
In a situation where you are close
to the minimum adjustment, fit only 1 wall
profile to the wall and put the second wall
profile into the frame, position the frame
onto the tray and then fix the second wall
profile to the wall.
NOTE:
Ensure the rollers are fitted in the
correct position.
FITTING DOOR PANELS AND ROLLERS
Top roller
8
Bottom roller
9
7
Step 8.
Assemble the top rollers using
spanner. Ensure you can see top
adjusting screw.
Step 9.
Assemble the bottom rollers using
.screw driver
IMPORTANT: Rollers have spring
for easy clean function.
NOTE:
Handle
towards
straight
fixed panel.
Adjusting screw

6
15 S6LC83291871
S6LC83291805
S6LC8431
Bottom
roller
Bottom
rail
Top roller
Top rail
push
down
10
14
V2101L/R
V2104
ensure the top rail is level
then go on to step 12
FINISHING
Outside
S6HDLEP7
S6HDLEP6
S6HDLEP1
S6HDLEP3
S6HDLEP4
S6HDLEP2
S6HDLEP5
11
Loosen nut ½ turn
to adjust
Inside
S6HDLEP7 13
Step 12.
Drill through upright and wall profile in 3 places, top to bottom as shown.
Step 13.
If the moving panels are not closing correctly, or there is any gap between
the magnets, adjust the roller by first loosening the nut behind the
roller slightly (max half turn). Then adjust screw at the top of the roller
and tighten nut. Ensure bottom rollers are running properly in the bottom
track
V6115
12
V4110
V2114
V2115
Step 10.
Hang the moving panel to the
top rail, then push the bottom
rollers bottom rail.
Ensure handle is towards
flat fixed panel.
into the
NOTE:

SEALING AND TROUBLE SHOOTING
DO NOT use
the
enclosure
for 24 hrs
TROUBLE SHOOTING GUIDE
Step 16.
Use a quality silicone sealant
and applicator gun to seal the
finished door.
Seal top to bottom on the
between the wall
profile and the wall.
Do not apply sealant on
the inside of the tray.
Seal only along bottom on the
between
glass/rail/profile and the tray
and approx 50mm up
between the wall profile and
the wall. Seal at vertical
joints on bottom of frame on
outside only.
SEALING INSIDE
INSIDE
Note:
SEALING OUTSIDE
OUTSIDE
7
DOOR NOT ALIGNING
1. Is the tray 100% level? ( )
2. Have the walls been checked at different levels to ensure consistency?
3. Are the wall profiles stepped in 20mm from the edge of the tray? ( )
4. Do the finished tile measurements on the tray comply with the adjustment listed on the
label and in the specifications book?
5.
6. Is the top rail level? ( )
DOOR LEAKING
2.Is the upright seal fitted? ( )
3.Is the door sealed correctly? ( )
see page 3
see step 1
see
see step 12
see step 15
see step 16
--
---
Are the rollers adjusted so the bottom rollers are running and not rattling in the
bottom track.( )
1.Have the rollers been adjusted so the moving panel is rolling and closing
correctly? ( )
---
--------
--
step 10,13
See step 13
50mm