MERLYN MB3B User manual

Two Panel Bath screen
NOTE: Please ensure the bathscreen
Is installed on the inside of the bath top.
inside edge
MB3B
BT007 / T-031

Fixing Kit components
- PH2 Philips Head screw driver
Neutral cure anti bacterial silicone
SP0MOBY002L/R
2
13
2SS008
Wall profile cover 2SP0MOBY002L/R
1
1
1
Wall profile LR8387C
A
1
Moving Glass Panel
Wall Plug 2SP12
3
3
3
3
3
Screw(4X40mm)
Screw Cover Cap
Screw Cover Cap Clip 2SS009
Fixed Glass Panel B
14
15
18
19
20
Clear Seal
1
2
1
Screw(3.5X30mm)
17
16
12SS009
SP0LF02
Bracket bottom Leakfree
Bracket top Leakfree SP0LF01
SP0LFCS
Top Bracket
SP0LF01
Bottom Bracket
SP0LF02
x1
x1
LP-123
x1
SP0M7029
1
foam plastics LP-123
Stabilising Bar BSYS023C
1
4
6
7
8
10
9
11
13
2
3
12
14
5
15
4x40
A2403001
4x12
A2401201
Screw(4X12mm)
A2403001
A2401201

1. Silicone on the bath edge if not siliconed previously fig 1.
FIG 1 1A
2. Insert the fixed panel B into the wall profile.Do not fix to the wall profile fig 2.
Top Bracket
SP0LF01
Bottom Bracket
SP0LF02
The left direction The right direction
FIG 2

Top
Bottom
screen
bath.Fig 4.
LR8387C
4.
3.Fit the bottom clear seal on to the bottom of the bathscreen fig 3 . SP0LFCS Apply silicone as shown in fig 3A firstly.
FIG 3
lnside
lnside
lnside
3E
3D
3C
lnside
3B
lnside
3A
edge
FIG 4
6 mm
x3
5B
5C
5D
FIG 5
5A
5.5. LR8387C
fix wall profiiles to wall.Fig 5.
Screw A2403001,

TOP
x3
6A
6B
6C
FIG 6
BOTTOM
Fig 7.
7.
bracket.
7C
7G
6 mm
7D
7E
7F
FIG 7
Top Bracket
SP0LF01
Bottom Bracket
SP0LF02
7A
7B
Note: Ensure bottom pivot bracket is always on the bottom of the fixed panel.
6. Drill 3 holes top,middle and bottom through the wall profile and fixed panel using a 3mm steel drill bit. Using the Screws
A2401201,and screw cover caps 2SS008 and screw cover caps clips 2SS009 fix the hinge upright to the wall profile in 3
places.Fig 6.
A2403001. Fasten

9A
FIG 8
8A 8B
8C
TOP BOTTOM
9. SP0MOBY002L/R and BSYS025C bath.Fig 8.
Outside
lnside
50mm50mm
FIG 9
50mm
lnside
Outside
8. Place moving panel into the bottom pivot bracket and fix the top pivot bracket into position as shown in 8A – 8C”.
Sealing.FIg 9
where the fixed panel and hinge bracket sit on the bath inside and outside.
Seal 50mm up where
Inside and outside :
Silicone
and outside.
Seal with silicone according to the position of inner and outer red thick lines.
the hinge upright and the fixed panel glass over lap.