Mesto CLEANER 3275PP User manual

MESTO Spritzenfabrik
Ernst Stockburger GmbH
Ludwigsburger Straße 71
D-71691 Freiberg/Neckar
Tel.: [phone]
Fax: [phone]
[email protected]
www.mesto.de
3275PP, 3270PP, 3275PE, 3270PE
3275P, 3270P
DE (DEUTSCH)
Gebrauchsanleitung......................... 6
EN (ENGLISH)
Instructions for Use ........................ 13
FR (FRANÇAIS)
Mode d‘emploi ............................ 20
NL (NEDERLANDS)
Gebruiksaanwijzing ........................ 27
ES (ESPAÑOL)
Instrucciones de uso . . . . . . . . . . . . . . . . . . . . . . . 34
IT (ITALIANO)
Istruzioni per l‘uso ......................... 41
PT (PORTUGUÊS)
Manual de instruções....................... 48
FIN (SUOMI)
Käyttöohje................................ 55
S (SVENSKA)
Brugsanvisning ........................... 62
N (NORSK)
Bruksanvisning............................ 69
DK (DANSK)
Brugsanvisning ........................... 76
EST (EESTI)
Kasutusjuhend ............................ 83
LT (LIETUVIŲ)
Naudojimo instrukcija ...................... 90
LV (LATVIEŠU)
Lietošanas instrukcija ...................... 97
GR (ΕΛΛΗΝΙΚΆ)
Οδηγίες χρήσης .......................... 104
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 1 14.02.2023 15:16:54

Ersatzteile Spare Parts Pièces de Rechange
Reserve-onderdelen Piezas de repuesto Pezzi di ricambio
Peças sobressalentes Varaosat Reservdelar
Reservdeler Reservedele Varuosad
Atsarginės detalės Rezerves daļas Άνταλλακτικά
3275PP, 3270PP, 3275PE, 3270PE
3275P, 3270P
www.mesto.de
3
2
6227KS
1623
1623
6707L (3275PP, 3270PP, 3275P, 3270P) 6707E (3275PE, 3270PE)
6224SB (3275PP, 3270PP) (3275P, 3270P) 6224SE (3275PE, 3270PE)
6307L (3275PP, 3270PP)
6307EM (3275PE, 3270PE)
6307LS (3275P, 3270P)
6126NA
6126NR (3275P, 3270P)
3654F (3275PP, 3270PP) 3654E (3275PE, 3270PE)
3655 (3275P, 3270P)
6133MB
6300VN
(3275PP, 3270PP) (3275PE, 3270PE)
6302P (3275P, 3270P)
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 2 14.02.2023 15:16:55

1a 1b
2 3
5 6 7 8
3
2
11
22
44
6
6
16 13
2
1
35
10
7
9
9
37
37 4
4
9
7
50
7
34
37
50 50
77
55
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 3 14.02.2023 15:16:56

9 10 11
13 14 16
17 18 19
5
4
2
13
16
9
40 40
7
1
2
2
19 19
20
20
9
9
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 4 14.02.2023 15:16:58

21 22
24 26
28 29
5
4
2
23
16
21
50
9
22
41
41
42
44
45 24
25
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 5 14.02.2023 15:16:59

12
13
Pressure spraying devices 3275PP, 3270PP and 3270P, 3275P are designed for the spray-
ing of cleaning and disinfecting agents and of building chemicals, such as for example wall
paper solutizer. Pressure spraying devices 3275PE, 3270PE are designed for the spraying
of alkaline detergents and care products. The manufacturer of the spraying agents has to
approve that they can be applied with sprayers.
EN ENGLISH
Welcome and congratulations
Usage
Not suitable for
•plant protection products
• inammable liquids
•corrosive substances (certain disinfecting and impregnating agents, acids and bases)
•liquids containing ammonia
•liquids at temperatures above 40 °C (104° F)
•wetting agents (surfactants), solvents, and liquids containing solvents which can cause
or promote cracking in the applied plastics
•viscous or sticky liquids or liquids that form residues (dyes, greases)
• use in applications for foodstu󰀨s
Under no circumstances should you use
• external sources of pressure without original compressed air lling valve
• for aming
•for storing and holding liquids
•as an eyewash
Make certain to read the instructions for use before using the device!
Keep the instructions for use in a safe place where they can be easily found.
The instructions for use are an integral part of the device and must be enclosed
when the device is passed on. Particular safety measures are required when
working with the device.
Improper use may result in dangerous injuries and environmental damage.
Nitric acid, acetic acid and propionic acid must only be used in concentrations of up to 10 %,
phosphoric acid and sulphuric acid in a concentration of up to 30 %, and potassium hydroxi-
de solution and caustic soda in a concentration of up to 20 %.
on purchasing your new quality product. Thank you for the trust you have shown in our brand.
Your satisfaction with our product and services is very important to us.
Please contact us if your expectations are not met.
You will nd our address on the title page of these instructions for use.
Follow the safety notices and data sheets of the substance manufacturers before each
application. Observe the specied maximum concentrations for chemical substances and
preparations. We will be happy to advise you on what best suits your needs.
Observe the legal and statutory regulations applicable in your country.
The device may be used outdoors or in well ventilated rooms only. Have the salesperson
or an expert show you how to operate the device if you are working with it for the rst time.
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 13 14.02.2023 15:17:02

14
15
EN ENGLISH
Safety
EN ENGLISH
Devices may not be used for spraying
plant protection liquids.
Only trained, healthy and rested people may work with the device. You
should not be under the inuence of alcohol, drugs or medication.
Children and adolescents must not use the device
Keep the spraying devices safe from access to children.
Take precautions to prevent hazardous substances from being misused.
→ Accident risk!
Keep bystanders away during spraying.
Never spray on people, animals, electrical devices and lines, into the wind,
or into bodies of water.
→ Risk of injury!
Wear appropriate protective clothing, goggles and respiratory protection in line
with the applicable national regulations when working with hazardous substances.
Avoid ignition sources in the environment.
Do not allow the device to remain under pressure and/or exposed directly to
sunlight. Make certain the device is not heated beyond the maximum
operating temperature. (→Table 1).
Protect the device from frost and ammonia.
Never blow through the nozzles or valves with your mouth.
→ Risk of poisoning!
There is a risk of slipping or tripping on smooth or wet surfaces, snow, ice,
on slopes and on uneven terrain.
Repairs and modications to the device are not permitted.
Have damaged parts or parts that do not work properly repaired immediately
by our customer service department or by service partners authorized by us.
The e󰀨ect of the safety valve must not be bypassed or made inoperative.
→ Explosion hazard!
Use only original spare and accessory parts.
We cannot assume any liability resulting from the use of third-party parts.
When pumping, always observe the pressure gauge to ensure the maximum
spraying pressure is not exceeded (→ Table 1).
All excess pressure must be released from the device before lling, after
use, before carrying out maintenance work, on work breaks, and before
placing it in storage.
Points to note when transporting the device: Transport the device in such
a way that it is protected against damage and tipping. All excess pressure
must be released from the device.
→ Explosion hazard!
If the device leaks at the container, immediately depressurise the device
and put it out of operation!
→ Risk of explosion!
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 14 14.02.2023 15:17:02

14
15
Visual inspection: Are the tank [1], pump [2], hose [4], shut-o󰀨 valve [9], piston pressure
gauge[16], and spray wand [7] and elbow [50] with nozzle [21] undamaged? (Fig. 1)
+Pay special attention to the connections between the tank – hose and the hose – shut-o
valve and to the condition of the pump threading and spray wand.
No leaks: Pump up the empty device to 2 bar (29 psi) (Fig. 11).
► The pressure must not decrease more than 0.5 bar (7,35 psi) within 30 minutes.
Function: Pull up the piston pressure gauge handle [16]. (Fig. 5)
► The pressure must dissipate.
1. Attach the carrying strap [6] on the tank. (Fig. 2)
2. Push the hose [4] into the xture [10] and secure it with the cap nut [37]. (Fig. 3)
3. Push the hose [4] onto the shut-o󰀨 valve [9] and secure it with the cap nut [37]. (Fig. 3)
4. Screw the spray wand [7] onto the shut-o󰀨 valve [9] (Fig. 3)
5. Screw the bow [50] onto the spray wand [7]. (Fig. 3)
Tank [1], pump [2], hose [4], instructions for use [5], spray wand [7], shut-o󰀨 valve [9], car-
rying strap [6], bow [50], cap nuts [37]. (Fig. 1a and 1b)
Type of device 3270PP, PE
3270P
3275 PP, PE
3275P
Max. lling amount 10 l (2.64 gal) 5 l (1.3 gal)
Total contents 12.5 l (3.3 gal) 8 l (2,1 gal)
Max. spraying pressure 3 bar (44 psi)
Max. operating temperature 40 °C (104° F)
Weight when empty 2.9 kg (6.4 lbs) 2.6 kg (5.7 lbs)
Gross weight max. 12.9 kg (28.4 lbs) 7.6 kg (16.5 lbs)
Material of tank polyethylene
Where device is carried on the side
Technical residual quantity < 0.07 l
Max. volume ow 1 l/min
Recoil force < 5 N
Pressure change from 0 to 3 bar min. 5000 x
EN ENGLISH
+You will nd the illustrations referred to above in the pages 3 – 5 of these
instructions for use.
Scope of delivery
Technical data
Table 1
Checks
Assembly
Check the device regularly and after a longer period of non-use, e.g. a winter break.
Have damaged parts or parts that do not work properly repaired immediately by our
customer service department or by service partners authorized by us.
+Using the lock [40] the lever on the shut-o valve [9] can be locked and unlocked.
Unintentional spraying is prevented after locking. (Fig. 14)
► If required, reset the lock [40] and activate the shut-o󰀨 valve [9]. (Fig. 14)
► The shut-o󰀨 valve must open and close.
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 15 14.02.2023 15:17:02

16
17
1. Pull up the red piston pressure gauge [16] until the tank is depressurized. (Fig. 5)
2. Press the piston rod with handle [13] down and turn it counterclockwise.
► The piston rod with handle is locked. (Fig. 6)
3. Unscrew the pump [2] from the tank. (Fig. 7)
Spraying pressure Spraying rate with at jet nozzle (original equipment)
1.5 bar (21.8 psi) 0.49 l/min
2.0 bar (29.0 psi) 0.56 l/min
3.0 bar (43.5 psi) 0.69 l/min
EN ENGLISH
Preparation
+We recommend you mix the spraying liquid in the device or premix it in an external tank:
Fill to 1/3 with water, pour in the spraying agent, and then add more water until full.
4. Add the spraying liquid to the tank [1] (Fig. 8)
5. Check the lling level with the scale [35] on the tank. (Fig. 8)
6. Screw the pump [2] into the tank. (Fig. 9)
7. Press the piston rod with handle [13] down and turn it clockwise.
► The piston rod with handle is unlocked. (Fig. 10)
8. Create the desired pressure (→ Table 2) in the tank (Fig. 11)
+The maximum pressure should not exceed 3 bar (red line on the piston pressure
gauge, Fig. 11). If the maximum pressure is exceeded, the safety valve will engage
and release the excess pressure.
9. Press the piston rod with handle [13] down and turn it counterclockwise. (Fig. 6)
► Piston rod with handle is locked.
Spraying
To prevent dripping, hold the spray wand up when rst spraying and activate
the shut-o valve until no more liquid mixed with air is emerging from the
nozzle.
2. If required, reset the lock [40] and activate the shut-o󰀨 valve [9]. (Fig. 14)
► Spraying may now begin.
3. Make certain the optimum spraying pressure is set (→ Table 2) on the pressure gauge
[16] (Fig. 11).
Table 2. Dependence: Spraying rate – spraying pressure
4. If the spraying pressure decreases more than 0.5 bar (7.3 psi) from the optimum level,
pump some more.
+If liquid mixed with air emerges from the nozzle, the tank is empty.
Observe the instructions in the section entitled „Safety“.
The device must be in an upright position.
If lling the tank from a water line, ensure that the line or a hose does not project
into the tank.
Observe the instructions in the section entitled “Safety”.
Operate the device only while it is vertical or suspended upright and nearly vertical.
Avoid allowing drops of spray to drift onto areas that are not being treated.
Observe the instructions of the spray product manufacturer!
1. Hang the device over your shoulder. (Fig. 13)
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 16 14.02.2023 15:17:02

16
17
EN ENGLISH
After Usage
Care and maintenance
Observe the legal requirements of your country for accident prevention and check
the device in regular intervals.
Unless otherwise specied, we recommend that an expert carries out an external
test every 2 years and an internal test every 5 years as well as a strength test every
10 years.
Observe the instructions in the section entitled “Safety”.
Never leave liquid in the device.
Collect and dispose of the residual liquid and the tank according to all applicable
laws, requirements and regulations.
Follow the instructions of the spray product manufacturer!
Clean the protective equipment and yourself every time after usage.
Observe the instructions in the section entitled “Safety”.
5. Wipe o󰀨 the device with a moist cloth.
6. For drying and storing the device, keep the tank [1] and pump [2] separate in a dry place
protected from sunlight and freezing temperatures (Fig. 16).
1. Pull up the red piston pressure gauge [16] until the tank is depressurized. (Fig. 5)
2. Lock the piston rod with handle [13]. (Fig. 6)
3. Unscrew the pump [2] from the tank. (Fig. 7)
4. Dilute the remaining quantity twice in a row with ½ liter of water each time and spray the
resulting liquid onto the treated area.
After using the device 50 times or at least once a year:
•Unscrew the pump [2] from the tank. (Fig. 7)
•Dismantle the pump [2]. (Fig. 17)
•Grease the O-ring [19] and the sleeve [20]. (Fig. 18)
•Assemble the pump.
•Lock the piston rod with handle [13] and screw the pump [2] into the tank [1].
•Clean the nozzle [21] under running water. (Fig. 22)
• Unscrew the handgrip [41] from the shut-o󰀨 valve [9].
• Remove the lter [22] and clean it under running water. (Fig. 24)
• Disassemble the shut-o󰀨 valve [9]. (Fig. 28)
a) Loosen the four screws and pull the half shells [42] apart.
b) Screw the sealing cap [45] from the valve body [44] and pull the pressure bolt [25]
from the valve body [44]. (Fig. 29)
•Grease the O-rings [24]. (Fig. 29)
• Assemble the shut-o󰀨 valve [9].
• Take the hose [4] with the discharge lter [34] out of the tank and clean the discharge
lter under running water. (Fig. 24)
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 17 14.02.2023 15:17:03

18
19
Fault Cause Remedy
No pressure builds up in
the device.
The pump is not screwed
on tightly.
Screw the pump on tightly.
O-ring [19] on the pump is
faulty.
Replace the O-ring (Fig. 19).
Diaphragm [20] is defec-
tive.
Replace the diaphragm (Fig.
19).
Liquid ows out of the
pump.
Valve disc [23] dirty or
defective.
Clean or replace the valve disc
(Fig. 21).
Piston pressure gauge
does not indicate any tank
pressure.
Safety valve blows o󰀨 too
early.
Piston pressure gauge [16]
is defective.
Replace the piston pressure
gauge (Fig. 26).
The nozzle does not spray
even though pressure is
present.
Nozzle [21] or / and lter
[22] is clogged.
Clean the lter (Fig. 24) or/and
nozzle (Fig. 22).
The shut-o󰀨 valve does not
close.
Liquid emerges without the
lever being activated.
O-rings [24] of the pres-
sure bolt [25] are not
greased / lubricated.
Faulty O-rings [24] or pres-
sure bolt [25].
Grease the O-rings of the
pressure bolt (dismantle shut-
o󰀨 valve → section „Care and
maintenance“) (Fig. 29)
Replace O-ring or pressure bolt
(Fig. 29).
EN ENGLISH
Faults
Contact address for additional information → see title page.
Use only original spare and accessory parts.
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 18 14.02.2023 15:17:03

18
19
0223 6993140
declare under our sole responsibility that the pressure spraying devices of the series 3275,
3270, as supplied meet all the relevant requirements of Directive 2006/42/EC of the EU.
We guarantee that from the time it is rst purchased for a period of the legally valid requi-
red warranty period (maximum 3 years) this device will not exhibit any material or proces-
sing errors. If defects are discovered during the warranty period, the manufacturer or the
distributor in your country will repair the device without charging for the labor or material or
(at the discretion of the manufacturer) replace the device itself or its defective parts. If such
defects are discovered, please contact us immediately. We require the invoice or cash
register receipt for purchase of the device. The warranty does not include wearing parts
(seals, O-rings, diaphragm, etc.) or defects, which have occurred due to improper use or
unforeseeable circumstances.
EN ENGLISH
Warranty
Declaration of Conformity
Original operating instructions
The data and illustrations in these instructions for use are for orientation only and not
binding in any way. The manufacturer reserves the right to make changes or improvements
to the products if these are considered appropriate without having to notify customers
owning a similar model about this fact.
according to EC Machinery Directive 2006/42/EC, Appendix II, No. 1A.
We, MESTO Spritzenfabrik Ernst Stockburger GmbH, Ludwigsburger Straße 71,
D-71691 Freiberg,
Furthermore, the device complies with the Directive 2014/68/EU for pressure equipment.
Rolf Rehkugler is authorized to compile the technical documentation.
Freiberg, Bernd Stockburger – Managing Director –
25/04/201
6993140_0223_CLEANER_PROFIPLUS_15Spr.indd 19 14.02.2023 15:17:03