METER ZL6 Operating and safety instructions

ZL6 Reference Barometer ZL6 Reference Barometer ZL6 Reference Barometer
The reference barometer sensor in the ZL6 data logger should be replaced if it malfunctions
or if it needs to be calibrated. These step-by-step instructions will explain the replacement
process. A #1 Phillips screwdriver is required forinstallation.
ACCESS REFERENCE BAROMETER SENSOR
CAUTION: Do not disconnect anywiring.
TEST
The reference barometer sensor in the ZL6 data logger should be replaced if it malfunctions
or if it needs to be calibrated. These step-by-step instructions will explain the replacement
process. A #1 Phillips screwdriver is required forinstallation.
ACCESS REFERENCE BAROMETER SENSOR
CAUTION: Do not disconnect anywiring.
TEST
The reference barometer sensor in the ZL6 data logger should be replaced if it malfunctions
or if it needs to be calibrated. These step-by-step instructions will explain the replacement
process. A #1 Phillips screwdriver is required forinstallation.
ACCESS REFERENCE BAROMETER SENSOR
CAUTION: Do not disconnect anywiring.
TEST
Main board
Sensor
REMOVE AND REPLACE SENSOR
Remove old
Insert new
Main board
Sensor
REMOVE AND REPLACE SENSOR
Remove old
Insert new
Main board
Sensor
REMOVE AND REPLACE SENSOR
Remove old
Insert new
3. Carefully lift up
the main board
and rotate over to
exposetheunderside.
4. Lifting straight up,
remove the existing
sensor and discard.
2. Remove the four
screws from the
main board using a
Phillipsscrewdriver.
1. Remove a battery toturn
off theZL6, and press
TEST buttonto clear
power in logger.
5. Pressing straight
down,insert the
newsensor into
the daughterboard
connector.
18317-00
5.15.2019
18317-00
5.15.2019
18317-00
5.15.2019
NOTE: No need to
disconnectthe antenna.
1. Remove a battery toturn
off theZL6, and press
TEST buttonto clear
power in logger.
2. Remove the four
screws from the
main board using a
Phillipsscrewdriver.
3. Carefully lift up
the main board
and rotate over to
exposetheunderside.
NOTE: No need to
disconnectthe antenna.
4. Lifting straight up,
remove the existing
sensor and discard.
5. Pressing straight
down,insert the
newsensor into
thedaughterboard
connector.
1. Remove a battery toturn
off theZL6, and press TEST
buttonto clear power in logger.
2. Remove the four
screws from the
main board using a
Phillipsscrewdriver.
3. Carefully lift up
the main board
and rotate over to
exposetheunderside.
NOTE: No need to
disconnectthe antenna.
4. Lifting straight up,
remove the existing
sensor and discard.
5. Pressing straight
down,insert the
newsensor into
the daughterboard
connector.

RETURN MAIN BOARD TO ORIGINAL POSITION
TEST
RETURN MAIN BOARD TO ORIGINAL POSITION
TEST
RETURN MAIN BOARD TO ORIGINAL POSITION
TEST
6. Carefully lift the
main board up
and rotate over so
batteries are visible.
7. Replace the screws.
9. Connect to the logger and check ZENTRA Utility to ensure barometer and
temperature readings are available. Press the TEST button on the ZL6 to reset
the logger if the readings do notappear.
CUSTOMER SERVICE
NORTH AMERICA
Customer service representatives are available for questions, problems, or feedback Monday
through Friday, 7:00 am to 5:00 pm Pacific time. through Friday, 7:00 am to 5:00 pm Pacific time. through Friday, 7:00 am to 5:00 pm Pacific time.
Email: [e-mail]
[e-mail]
Phone: [phone]
Fax: [phone]
Website: metergroup.com
EUROPE
Customer service representatives are available for questions, problems, or feedback Monday
through Friday, 8:00 to 17:00 Central European time.
Email: [e-mail]
[e-mail]
Phone: [phone]
Fax: [phone]
Website: metergroup.de
If contacting METER by email, please include the following information:
Name
Address
Email address
Phone
Instrument serial number
Description of the problem
NOTE: For products purchased through a distributor, please contact distributor directly for assistance.
CUSTOMER SERVICE
NORTH AMERICA
Customer service representatives are available for questions, problems, or feedback Monday
Email: [e-mail]
[e-mail]
Phone: [phone]
Fax: [phone]
Website: metergroup.com
EUROPE
Customer service representatives are available for questions, problems, or feedback Monday
through Friday, 8:00 to 17:00 Central European time.
Email: [e-mail]
[e-mail]
Phone: [phone]
Fax: [phone]
Website: metergroup.de
If contacting METER by email, please include the following information:
Name
Address
Email address
Phone
Instrument serial number
Description of theproblem
NOTE: For products purchased through a distributor, please contact distributor directly for assistance.
CUSTOMER SERVICE
NORTH AMERICA
Customer service representatives are available for questions, problems, or feedback Monday
Email: [e-mail]
[e-mail]
Phone: [phone]
Fax: [phone]
Website: metergroup.com
EUROPE
Customer service representatives are available for questions, problems, or feedback Monday
through Friday, 8:00 to 17:00 Central European time.
Email: [e-mail]
[e-mail]
Phone: [phone]
Fax: [phone]
Website: metergroup.de
If contacting METER by email, please include the following information:
Name
Address
Email address
Phone
Instrument serial number
Description of theproblem
NOTE: For products purchasedthrough a distributor, please contact distributor directly for assistance.
8. Replace the
removed battery.
6. Carefully lift the
main board up
and rotate over so
batteries are visible.
7. Replace thescrews. 8. Replace the
removed battery.
9. Connect to the logger and check ZENTRA Utility to ensure barometer and
temperature readings are available. Press the TEST button on the ZL6 to reset
the logger if the readings do notappear.
6. Carefully lift the
mainboard up
and rotate over so
batteries are visible.
7. Replace thescrews. 8. Replace the
removed battery.
9. Connect to the logger and check ZENTRA Utility to ensure barometer and
temperature readings are available. Press the TEST button on the ZL6 to reset
the logger if the readings do notappear.