METHVEN Aroha 01-9267 User manual

Methven Australia Pty Ltd
ABN 15 104 813 390
Melbourne, Australia
www.methven.com
WMKA21005
IMPORTANT
Please read all of the instructions before installation
MA019267
Aroha Bidet Mixer
01-9267
Use of this product is recommended for domestic and commercial applications.
All pipework must be thoroughly flushed prior to the installation of the mixer.
Inline filter washers must be installed on both hot and cold supplies to prevent foreign particles
damaging the ceramic head works.
Do not remove the ceramic cartridge from the mixer when installing.
Methven recommends a licensed plumber carry out all installations in compliance with
the requirements of AS/NZS 3500. This product complies with AS/NZS 3718 regulations.
June 2012
Installation Guide
Installation
Tip: Install product on bench before
connecting second hose to mixer.
1. Cut a single 35mm diameter hole into
the mounting surface. The mounting
surface can be a maximum of 40mm
thick.
2. Insert o-ring (3) into the groove in the
bottom of the mixer (1).
3. Feed the mixer’s (1) threaded
fastening tube through the hole cut in
the mounting surface.
4. Position the mixer (1) as desired and
fit the rubber washer (4) over
the threaded fastening tube. Tighten
the mounting nut (5) in place using
the tube spanner (9) from under the
mounting surface.
5. Insert the flexible hoses (7) through
the hole in the mounting surface (from
the underside) and screw them into
the base of the mixer body (1).
6. Connect the flexible hoses to the hot
and cold supplies (hot on the left,
cold on the right).
Note: It is recommended that the
inline filter washers supplied are
fitted during this connection.
7. Fit “pop-up” waste outlet (B) into
Bidet bowl.
8. Remove side nut (C) and insert rod
with ball (D). Fit washer supplied and
replace side nut (C).
9. Join extension rod (E) to “pop-up”
lever (A) under bowl.
10. Using “universal joint” provided (F)
join and adjust rods to maintain
“pop-up” action.
www.methven.com
Customer Care Hotline: 1300 METHVEN (638 483)
Email: [email protected].com
Hot
Max 40mm ø35mm Min
ø38mm Max
Cold

R35mm Min
20mm
DO NOT CRUSH
HOSE OR SWAGED ENDS
CORRECT
INCORRECT
DO NOT STRETCH OR TWIST HOSES
Tube spanner
9
Stream shaper
Fast Fit Tube
O-Ring
Rubber Washer
Pop up Waste
Flexible inlet hose:
cold
hot
Mounting Nut
Mixer Body
Technical Specification
Inlet Connections: All 1/2" BSP
Operating Pressure: 150kPa - 500kPa
For optimum performance hot and cold water pressures should be equal.
AS/NZS 3500 stipulates a 500kPa maximum operating pressure at any outlet
within a building. Where normal pressure exceeds 500kPa, a pressure limiting
valve must be installed.
Operating Temperature: Recommended hot water supply 50°C, maximum 70°C. AS/NZS 3500 requires all
hot water supplies to any sanitary fitting to be tempered to 50°C.
Ceramic cartridges: Ceramic cartridge can be damaged due to the presence of the following within the
water supply:
Copper tube pieces
Plastic pieces
Sand, dirt or stones
Thread tape
Other objects not normally present in the potable water supplies
Hose Requirement for Mixers
Do not hydrostatic test* the installation with this mixer installed. Damage to the ceramic cartridge
may occur.
*Hydrostatic testing refers to placing the system under pressure, above the recommended operating
pressure, to determine water tightness and to uncover leaks or weak joints within the system.
Care and Cleaning
Never use abrasives to clean this product. Clean regularly with contamination free warm soapy water
and a damp soft cloth.
www.methven.com
Customer Care Hotline: 1300 METHVEN (638 483)
Email: [email protected].com
Pop Up Waste Parts
Please check every component in accordance
with the table below
A Pop up lever 1
B Pop up waste outlet 1
C Nut 1
D Rod with ball 1
E Extension rod 1
F Universal joint 1
FA EB CD
1
3
4
5
7