Metra Electronics 95-7866B User manual

INSTALLATION INSTRUCTIONS FOR PART 95-7866B
95-7866B
APPLICATIONS
ACURA MDX 2001-2006
KIT FEATURES
•Double DIN Head Unit Provision
•ISO Stacked Head Unit Provision
•Painted Matte Black to Match Factory Dash
A) Double DIN Radio Housing • B) DDIN Brackets (Tohold Display above radio)
KIT COMPONENTS
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver • Socket Wrench
1-800-221-0932
©COPYRIGHT 2003-2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
•70-1721 Honda harness - 1998-up
•40-HD10 -Honda antenna adapter- 2005-up

Dash Disassembly
- ACURAMDX2001-2006......................... . . . . . . 1
Kit Preparation
-Display Unit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Kit Assembly
-Double DIN Head Unit Provision .............................. 3
-ISO Stacked Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TABLE OF CONTENTS
95-7866B
*Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skills
by enrolling inthe most recognized andrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 formore information
and take stepstoward abetter tomorrow.

95-7866B DASH DISASSEMBLY
ACURA MDX2001-2006
A
B
1
1
Remove (6) mounting screws and
remove the audio/display unit from
the dash. ( Figure B)
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
3
Remove (8) screws from the audio
unit and (4) screws from the display
unit and remove the brackets from
the audio/display assembly.
4
Unclip and remove trim panel around
radio/display including a/c vents.
(
Figure A)
2
Continue to kit preparation.

95-7866B KIT PREPARATION
2
A
B
DISPLAY UNIT ASSEMBLY
Using the mounting screws from the
display unit, attach the brackets
supplied with the kit by aligning the
guide pins on the display with the
holes on the brackets.
(Figure A)
1
Align guide pins on bottom of display
unit with holes on top of housing and
attach the unit to the housing using
the (2) screws previously removed.
(Figure B)
2
Continue to kit assembly.
* Note: Refer also to the instructions included with the aftermarket radio.

95-7866B KIT ASSEMBLY
3
DOUBLE DIN HEAD UNIT PROVISION/
ISO STACKED HEAD UNIT PROVISION
1
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from
Metra or AXXESS. Re-connect the
negative battery terminal and test
the unit for proper operation.
3
Reassemble dash in reverse order of
disassembly.
2
Slide the Double DIN head unit or
stacked ISO head units into the
bracket/radio housing assembly and
secure the Double DIN head unit or
stacked ISO head units to the
assembly using the screws supplied
with the radio.
(Figure A)
* Note: Refer also to the instructions included with the aftermarket radio.
A

NOTES
4
95-7866B

NOTES
5
95-7866B

95-7866B INSTRUCTIONS
1-800-221-0932
REV. 08/24/09 © COPYRIGHT 2003-2009 METRA ELECTRONICS CORPORATION INST99-7866B
www.metraonline.com